• 한국자동차공학회논문집
• /
• 제16권1호
• /
• pp.8-13
• /
• 2008

Emissions from automobiles have long been considered a prime source of pollutants involved in smog formation and ozone production. Especially VOCs are associated with serious environmental problems such as photo-chemical smog as well as human health effects. Since motor vehicles are a major source of VOCs, estimating of emission from mobile source is the most important factor to control VOCs. VOCs are emitted from various pollution like motor vehicles, mobile and stationary source that has characteristics of toxicity, cancer-causing, bio-accumulation, durability in air and diffusion can exert a bad influence upon human health and environment. However we don't have any standard or regulation about VOCs emissions. This study is summarized as VOCs emission characteristics from in-use light-duty diesel and LPG fueled vehicles. The vehicle exhaust-gas test mode is CVS cycle and nier-10 cycles that developed on EPA and National Institute of Environmental Research. TO-14 method (Toxic Organic) was chosen for VOCs analysis from EPA in USA. This study results will be useful when make a emission factor and rule making of emission standard about domestic VOCs emission for the improve to air condition.

• 터널과지하공간
• /
• 제22권5호
• /
• pp.365-372
• /
• 2012

본 논문에서는 환기구의 존재, 환기구 설치 대수, 환기구 용량, 복수 화원의 존재가 도로터널에서 발생한 차량 화재에 의한 연기 온도 분포에 미치는 영향을 평가하였다. 6개의 시나리오를 가정하였으며 FDS를 이용하여 시나리오 해석을 실시하였다. 해석 결과 환기구의 설치 대수가 증가함에 따라 연기의 온도는 감소하는 것으로 나타났지만, 환기구의 설치 대수가 2대인 경우와 3대인 경우에 온도 감소 효과는 거의 같은 것으로 나타났다. 환기구의 설치 용량은 환기구의 설치 대수 보다 연기 온도 감소에 더 큰 영향을 주는 것으로 해석되었다. 환기구가 없는 시나리오 No. 1과 복수 화원을 갖는 시나리오 No. 6를 제외한 나머지 시나리오에 대해서 해석한 결과 화원 상부에서의 연기 온도는 모두 $400^{\circ}C$ 이하로 나타났는데, 이는 화원 상부 연기층에서 발생하는 복사에 의해 화원 주변 가연물의 착화가 어렵다는 것을 나타낸다.

• 한국환경과학회지
• /
• 제30권3호
• /
• pp.219-234
• /
• 2021

Industrial emissions, mainly from industrial complexes, are important sources of ambient Volatile Organic Compounds (VOCs). Identification of the significant VOC sources from industrial complexes has practical significance for emission reduction. VOC samples were collected from July 2019 to June 2020. A Positive Matrix Factorization (PMF) receptor model was used to evaluate the VOC sources in the area. Four sources were identified by PMF analysis, including coating-1, coating-2, printing, and vehicle exhaust. The coating-1 source was revealed to have the highest contribution (41.5%), followed by coating-2 (23.9%), printing (23.1%), and vehicle exhaust (11.6%). The source showing the highest contribution was coating emissions, originating from the northwest to southwest of the sample site. It also relates to facilities that produce auto parts. The major components of VOC emissions from the coating facilities were toluene, m,p-xylene, ethylbenzene, o-xylene, and butyl acetate. Industrial emissions should be the top priority to meet the relevant control criteria, followed by vehicular emissions. This study provides a strategy for VOC source apportionment from an industrial complex, which is helpful in the development of targeted control strategies.

• 산업경영시스템학회지
• /
• 제20권44호
• /
• pp.463-473
• /
• 1997

In this paper, driver's judgements for the priorities of vehicle devices were studied to establish the standard of design of inside devices. The differences within drivers who have different careers were also studied. For this study, two experiments were conducted. First experiment was peformed in terms of total devices in the vehicle cockpit, and second was peformed in terms of the visual devices that these were the source of visual information. These experiments were analyzed using AHP (Analytic Hierarchy Process) method. The result showed the priorities of devices and little relationship between the career and the judgement. Especially, it was shown that the novice tended to depend on the information from visual devices.

• Journal of Advanced Marine Engineering and Technology
• /
• 제24권1호
• /
• pp.119-126
• /
• 2000

In constructing the positioning system based on a conventional dead-reckoning for a wheeled vehicle with pneumatic tires, the position estimation error is inevitable as changes of the radius of the wheels depend on live load and variable enviroment. Therefore, this paper proposes the positioning system which can estimate the error source i.e. the vehicle parameter errors, such as the right and left wheel radius error, using gyroscope and ultrasonic sensor and correct the parameter to reduce the dead-reckoned position estimation error. The extended Kalman filter was used as a method for the multisensor data fusion. The simulation to verify the effectiveness of the proposed positioning system is performed.

• 한국기계가공학회지
• /
• 제15권3호
• /
• pp.58-65
• /
• 2016

This study analyzed the structural weld strength for a door hinge for a field artillery ammunition support vehicle. In order to determine the optimal conditions, we measured the modal analysis and analyzed the leg length of a rear door hinge. From these methods, we acquired the vibration frequency of normal mode and the optimal welding leg length conditions. It was possible to obtain a structural stability for a rear door hinge of the field artillery ammunition support vehicle. In the future, this should be used as a reference source for the weld strength analysis of high vibration and high weight structures for another welding system design.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2005년도 제17회 워크샵 및 추계학술대회
• /
• pp.537-540
• /
• 2005

A battery is the primary energy source device presently used in hybrid electric vehicle. It can store much energy, but cannot provide enough current without inefficient units. However, an ultracapcitor can provide much current, but cannot store much energy. It will have better fuel economy by combining the two energy sources in parallel. The purpose of this paper is making the simulator of the two HEV systems. The one has only battery, the other have battery and ultarcapacitor in parallel. To compare the fuel economy, dynamic programing was used for optimization and prius was used for HEV model.

• 한국소음진동공학회논문집
• /
• 제15권6호
• /
• pp.674-679
• /
• 2005

Statistical Energy Analysis(SEA) has been considered as a Possible method for predicting responses of complex structures, especially at higher frequencies. In this paper, an SEA model of a vehicle was built using 138 energy storing subsystems connected together using 1019 Junctions. SEAM software program was used to build and calculate the model. To demonstrate the accuracy of the SEA model, predicted response levels were compared with measured levels. The source Input levels were measured at the engine mounting parts. There is good agreement between the estimated and the experimental results. This paper also identifies some dominant energy flow paths from sources. It is finally presented that the SEA model can optimize the design parameters of vehicles using model parameters and energy flow paths.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2007년도 춘계학술대회논문집
• /
• pp.501-506
• /
• 2007

Structure-borne noise is the interior noise that results from the low frequency vibrational energy transmitted through those body and joint parts. The relation between the excitation of powertrain and resultant interior sound must be analyzed in order to identify and predict the structure borne noise. The method of acoustic source excitation is preferred than the method of mechanical force excitation to measure the NTF(noise transfer function). Because acoustical method is more convenient and reliable. In this paper, to analysis and identify vehicle interior noise by powertrain is performed, and the vibro-acoustic transfer function is extracted from experimental measurement. These are important step of TPA(transfer path analysis) to identify effect of interior noise resulted from powertrain running excitation.

• 한국자동차공학회논문집
• /
• 제5권4호
• /
• pp.84-92
• /
• 1997

Among the various sources of vehicle interior noise, this paper concerns the road induced noise ; the identification of its transfer path by using experimental method. Multiple input and single output model is taken as a noise generation model. Because it is impossible to measure the road imput forces directly, the acceleration signals are measured on four axle;three directions for each point. By considering the cross correlations of input signals, four uncorrelated source groups are taken. Multiple coherence function is employed to investigate the contribution of each group. In addtion, to identify the detailed path through the suspension systems, the contributions of all possible paths are ranked by using the coherence functions between interior noise and the relative accelerations of connections such as bushings and mountings. Measurements are performed with passenger vehicle traveling on concrete and asphalt roads at 60㎞/h.