• Journal of the Korean Institute of Gas
• /
• v.20 no.6
• /
• pp.9-15
• /
• 2016

Liquefied petroleum gas (LPG) and compressed natural gas (CNG) are often used as fuel for vehicles because they are clean alternative gas fuels. CNG, as a low-carbon fuel, can contribute to the reduction of greenhouse gas emissions. LPG is often used as fuel for taxis because the performance is almost the same as that of gasoline but the price is lower. In the present study, the exhaust gas and the particle number (PN) of particulate matter, which is a recent environmental issue, were compared between LPG and CNG for the same vehicle. A chassis dynamometer was used to conduct the test according to the Federal Test Procedure (FTP)-75 and Worldwide harmonized Light-duty vehicle Test Procedure (WLTC) modes. The PN values of discharged particles having sizes of 5 nm or larger and 23 nm or larger were measured using two condensation particle counters (CPC). The ratio of carbon dioxide was high in the exhaust gas from the LPG vehicle; the ratio of methane was high in the exhaust gas from the CNG vehicle. The PN values of the emitted particles from the two fuels were similar. The PN values of particles having sizes of 23 nm or smaller were high in the high-speed WLTC mode.

• Journal of Korean Society for Atmospheric Environment
• /
• v.30 no.5
• /
• pp.449-460
• /
• 2014

Since the emergence of domestically produced automobiles in 1964, the number of automobiles in circulation in South Korea has increased constantly. With this rapidly increasing number of automobiles, automobile-induced environmental pollution has become an issue of great concern, especially with regard to air pollution. Of the carbon composites contained in automobile exhaust gas, PAHs are known to be carcinogenic and highly deleterious to humans and thus need to be urgently mitigated. To address this issue of PAHs, this study was conducted to estimate qualitative of particulate PAHs contained in carbon composites in automobile exhaust gas, by capturing all particulate matter discharged from the latter. To allow for differentiated analyses, the automobiles investigated were divided into 4 groups: gasoline vehicle, motocycle, diesel vehicle, and LPG vehicle. Samples were analyzed using two methods. First, in-depth analysis was performed on organic carbon (OC) and elemental carbon (EC) composites with analysis parameters, using the Thermal Optical Transmittance Method (NIOSH 5040). Second, for the examination of particulate PAHs, GC/MSD was used to analyze the 16 PAH species specified by the Environmental Protection Agency (EPA). The analyses yielded the findings that diesel vehicles had the highest mass concentration ($2,007{\mu}g/m^3$), followed by motocycle ($1,066{\mu}g/m^3$), LPG vehicle ($392{\mu}g/m^3$), and gasoline vehicles ($270{\mu}g/m^3$). The highest carbon concentrations in total particulate matter by vehicle weight were produced from LPG vehicle (79.8%), followed by gasoline vehicle (77.4%), motocycle (69.8%), and diesel vehicle (59.1%).

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.6
• /
• pp.689-695
• /
• 2018

This paper presents the means of controlling the regeneration of a diesel particulate filter (DPF) that is mounted on tactical vehicles to satisfy exhaust gas standards. The DPF captures particulate matter in the exhaust gas and combusts the captured particulate matter. This process is regeneration, which is essential to the normal performance of the DPF. Bad regeneration causes degradation of vehicle performance; worse, it can lead to a vehicle fire. DPF regeneration is performed by control logic. If the regeneration control logic does not properly reflect the operating characteristics of the vehicle, DPF regeneration may not occur. Consequently, it is very important to ensure the DPF operates properly by reflecting the operating characteristics of the tactical vehicle. This study analyzes the operational characteristics of a tactical vehicle and the DPF, and adds proper DPF regeneration control logic. Additionally, this study is intended to simultaneously improve the additional problems that may occur from operating under the added regeneration control logic.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.11a
• /
• pp.913-917
• /
• 2007

The turbocharger for a vehicle is consisting of a centrifugal compressor and turbine. These compressor and turbine are vibrating and emitting noises through the T/C body, exhaust system (Catalyst, Bellows, Pipe, etc) and Intake system (Hoses, Intercooler pipes, Intercooler) as rotating. A turbocharger cold test bench is constructed to reduce these noises, especially for the purpose of realizing transient operating environment and oil temperature control to simulate the vehicle operating characteristics with intake system and exhaust system. This research laid the groundwork to develop a lower noise level T/C through understanding the mechanism of the noise source of T/C.

• Journal of ILASS-Korea
• /
• v.12 no.1
• /
• pp.65-70
• /
• 2007

This paper is to investigate the characteristics of exhaust emissions and nano-particle emission from diesel passenger vehicle according to using biodiesel fuel as an alternative fuel. In this work, the particulate matters (PM) of exhaust emissions in diesel engine were investigated by number of particles and mass measurement. The mass of the total PM was measured using the standard gravimetric measurement method, the total number concentrations were measured on a ECE15+EUDC driving cycle using Condensation Particle Counter (CPC). Total PM emission was reduced $2{\sim}38%$ and number concentration was reduced $1{\sim}27%$ according to increasing blended ratio of biodiesel with diesel fuel. Total PM emission was reduced more than particle number emission because volatile particles were measured in total PM but were not measured in particle number emissions.

• Transactions of Materials Processing
• /
• v.25 no.3
• /
• pp.176-181
• /
• 2016

The exhaust tail pipe is the only visible part of the exhaust system on a vehicle. The conventional way to make the tail pipe is welding after stamping. There are various problems that occur during the stamping of stainless steel sheets such as scratching and local fracture. Problems during welding can also occur due to poor weldability. Tube hydroforming can be a solution, which eliminates these problems. The current study deals with the development of tube hydroforming for a vehicle tail pipe using finite element analysis for a free-feeding method. The current study focuses on the development of a proper load path for the tail pipe hydroforming and how bending influences the subsequent processing steps. The FE analysis results were compared with experimental results. This study shows the importance of bending and the necessity of considering bending when performing a tube hydroforming analysis.

• Journal of the Korean Society of Visualization
• /
• v.8 no.1
• /
• pp.25-30
• /
• 2010

The flow characteristics under recirculation cool vent mode is numerically studied using commercial fluid dynamic code(CFX). For the reliable analysis, real vehicle and human FE model is employed in grid generation process. The geometrical location and shape of panel vent, and exhaust vent is set as that of real vehicle model. The flowrate of the working fluid is determined as 330CMH which is equivalent to 70 percent of maximum capacity of HVAC system. The high velocity regions are formed around 4 each panel vent. Because of the non-symmetrically located exhaust, non-uniform flow and partial backflow near the door trim is observed. Streaklines start from each panel vent show the flow pattern of the airflow in the passenger's compartment very well.

• Tunnel and Underground Space
• /
• v.6 no.1
• /
• pp.64-68
• /
• 1996

Analyzed in this paper is fluid flow in the region near the exhaust and blower ports of the ventilation ducts inside a vehicle tunnel. Theoretical analysis shows that prediction of the energy loss in this region is important for designing the ventilation system. A finite-difference numerical model for the two-dimensional turbulent flow field was used to obtain the flow solution as well as the energy loss. It was shown that the blower-nozzle angle ($\beta$) had an important role in establishing both the pressure gradient and the energy loss, while the effect of the distance between two ports on them was not so significant.

• Proceedings of the Korea Air Pollution Research Association Conference
• /
• 2008.10a
• /
• pp.75-77
• /
• 2008

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.10a
• /
• pp.659-663
• /
• 1997

In this paper, a simplified vibration analysis model for bellows was presented to avoid excessive effort required for shell model. To reduce degree of freedom, bellows was modelled using one dimensional beam element. The equivalent mass and stiffness matrices were obtained based upon Guyan reduction process. The results were compared with the confirmed results, which were in good agreement.