• 드라이브 ㆍ 컨트롤
• /
• 제20권3호
• /
• pp.9-14
• /
• 2023

In this paper, the selection of a reliable accelerated life test code for a 2-ton forklift was accomplished by choosing the driving resistance coefficient failure-free test time based on a 10,000-hour B₁₀ life. The overall life and average equivalent load of the vehicle were then calculated based on actual driving test conditions using the selected driving resistance coefficient. The gear train's accelerated life test code was selected by adjusting the equivalent load to a torque and rotation speed that did not exceed 125%(about 75HP) of the vehicle rated power. The safety of the test standards was validated by conducting an actual accelerated life test utilizing the proposed test method in this study and comparing the test result with the corresponding theoretical value. It is anticipated that the reliability of the accelerated life test in this paper will be enhanced, by incorporating actual driving performance data collected directly from the forklift and adjusting the conditions used in developing the accelerated life test code.

• 한국자동차공학회논문집
• /
• 제22권2호
• /
• pp.166-174
• /
• 2014

Fuel injection pressure has steadily increased in diesel engines for the purpose of improving fuel efficiency and cleaning exhaust gas, but it has now reached a point, where the cost for higher pressure does not warrant additional gains. Common rail systems on modern diesel engines have fuel pumps that are mechanically driven by crankshaft. The pumps actually house two pumping module inside: a low pressure pump component and a high pressure pump component. Part of the fuel compressed by the low pressure component returns to the tank in the process of maintaining the pressure in the common rail. Since the returning fuel represents pumping loss, fuel economy improves if the returned fuel can be eliminated by using a properly controled electrical fuel pump. As the first step in developing an electrical fuel pump the fuel supply system on a 6 liter diesel engine was modeled with AMESim to analyze the workload and the fuel feed rate of the injection pump, and the results served as basis for selecting a suitable servo motor and a reducer to drive the pump. A motor controller was built using a DSP and a program which controls the common rail pressure using a proportional control method based on the target fuel pressure information from the engine ECU. A test rig to evaluate performance of the fuel pump is implemented and used to show that the newly developed electrically driven fuel pump can satisfy the fuel flow demand of the engine under various operating conditions when the rotational speed of the pump is adequately controlled.

• 한국자동차공학회논문집
• /
• 제8권3호
• /
• pp.85-97
• /
• 2000

In this paper, static and dynamic shift control stategies of CVT speed ratio are suggested. For the static shift control, in order to operate engine on the optimal operating region, a fuzzy control logic is used. In the fuzzy logic, S- factor that is defined as a degree of sportiness is introduced. Simulation results show that the static shift control strategy based on the fuzzy logic selects the optimal operating point automatically between the economy and the sporty mode corresponding to the driver's desire and the driving condition. For the dynamic shift control strategy, a shift speed map is suggested which determines the shift sped as fast or slow based on Δi, the difference between the desired speed ratio id and the actual speed ratio i, and throttle opening. It is seen from the simulation results that the CVT shift speed is determined by the dynamic shift control strategy to provide appropriate performance and comfort for the driver's demand and driving condition. Additionally, experiments are performed to investigate the dynamic performance of the shift speed for the lift foot up. From the experimental results, it is found that improved shift feeling can be obtained by the dynamic shift control strategy when lift foot up occurs.

• 한국자동차공학회논문집
• /
• 제9권5호
• /
• pp.105-114
• /
• 2001

In this study, a shift control algorithm far improving the shift quality of a parallel hybrid drivetrain with an automated manual transmission (AM) is proposed. The general AMT requires the sophisticated control of clutch in the clutch engagement to improve its shift characteristics, and that is generally known to be difficult. But in this hybrid drivetrain, we can control the speeds of clutch plates by engine and motor control, and it provides the easier clutch control in shift process than general AMT. Additionally, it permits the much-reduced shift shock. The motor control during the shift period is also to achieve reduced velocity drop of the vehicle in comparison with that of a general AMT. Furthermore various dynamometer-based experiments are carried out to prove the validity of the proposed shift control algorithm.

• 한국가스학회지
• /
• 제20권6호
• /
• pp.37-42
• /
• 2016

이 논문의 목적은 승용자동차의 배출가스 제어장치에 대한 고장사례 연구이다. 첫 번째 사례의 원인은 퍼지 컨트럴 솔레노이드밸브(PCSV)가 일정한 동작조건에서 열리지 말아야 하나, 오작동 되어 열림으로써 서지탱크로 증발가스가 유입되어 이것이 연료량이 농후한 것으로 측정되었다. 이 결과 엔진의 ECU(Electronic control uint)에서 연료의 분사량을 줄임으로써 공회전시 엔진의 부조화 현상이 발생된 것으로 확인되었다. 두 번째 사례에서는, EGR 밸브를 작동하는 호스가 다른 곳으로 조립되어 진공압력이 공급되지 않았다. 이로 인해 EGR 밸브가 작동되지 않고 다른 곳에서 진공이 누설됨으로써 엔진이 부조화 현상이 발생된 것으로 확인되었다. 세 번째 사례는 두개의 센서 가운데 뒤쪽(Rear side) 산소센서가 다른 자동차의 산소센서로 오장착됨으로 인해 산소량을 감지하지 못해 감속시 급격하게 속도가 줄어든 것으로 확인되었다. 따라서, 배출가스 제어 장치에 관련된 시스템은 최적의 상태로 작동되어 배출가스를 저감하는 역할을 할 수 있도록 철저한 관리가 요구된다.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2005년도 제24회 춘계학술대회논문집
• /
• pp.219-224
• /
• 2005

본 연구는 CRW형식 무인항공기 추진시스템의 밸브 작동을 고려한 비행모드에 따른 천이성능특성을 파악하기 위해 SIMULINK를 이용하여 모델링 하였다. 주 엔진시스템의 천이모사에는 ICV 방법이 적용되였다. 그리고 밸브 시스템은 로터리 덕트와 메인 덕트로 빠져나가는 유량을 제어하는 시스템으로서 밸브를 통해 로터리 덕트로 빠져나가는 유량과 메인 덕트를 빠져나가는 유량이 합은 터빈의 출구 유량과 같다는 가정하에 수행 되었으며, 이때 밸브각 변화에 따른 손실, 유량 및 유효 면적 등이 고려되었다. 성능해석은 비행 천이 영역인 고도 1Km 비행 마하수 0.1에서 엔진최대회전수시 회전익 모드에서 고정익 모드로 변환시외 고정익 모드에서 회전익 모드로 변환 경우들이 수행되였다.

• 한국항공우주학회지
• /
• 제47권10호
• /
• pp.738-746
• /
• 2019

한국형발사체 3단에 사용되는 7톤 짐벌엔진의 추력벡터제어에는 전기유압식 구동장치시스템 대신 중량, 비용 및 시험평가 등의 측면에서 더 효율적인 전기기계식 구동장치시스템을 사용한다. 전기기계식 구동기는 위치제어 서보 구동기로 고진공에서도 운용 가능한 BLDC 모터를 사용한다. 짐벌엔진을 갖는 발사체의 경우 구동기 자체 진동모드와 구동기를 지지하는 기체구조체의 벤딩모드, 짐벌엔진의 관성부하 등이 조합되어 합성공진 현상이 발생할 수 있다. 합성공진이 발생할 경우 발사체 자세제어는 불안정해진다. 이러한 관계로 짐벌엔진 및 기체구조체 지지부, 구동장치시스템의 고유 특성을 고려하여 강성에 대한 요구규격이 적용되어 왔다. 한국형발사체 3단 7톤 짐벌엔진의 경우 구동장치시스템의 강성요구규격은 $3.94{\times}10^7N/m$ 수준이며 이를 만족시키기 위한 직구동 방식전기기계식 구동기를 설계하였다. 본 논문에서는 강성요구규격을 기반으로 설계된 직구동 전기기계식 구동기의 등가강성 해석모델을 제안하고, 이를 실험결과로 검증하였다.

• 한국전자통신학회논문지
• /
• 제9권1호
• /
• pp.83-90
• /
• 2014

본 논문에서는 BLDC 모터로 구동되는 오일 펌프 제어 시스템을 설계하고 구현하는 문제를 다룬다. 제안된 오일 펌프는 하이브리드 차량에 장착되어 엔진 클러치와 변속기에 충분한 양의 작동유를 공급하는 역할을 한다. BLCD 모터로 구동되는 제어기를 단순화하여 전원 전압을 PWM 방식으로 직접 제어하는 일반적인 방법을 사용함으로써 응답성 및 정확성을 향상시키는 것을 주목적으로 한다. 제안된 제어 기법은 오일 펌프 장치의 효율성과 신뢰성을 높인다. BLCD 모터의 회전과 오일 펌프 가동 실험을 실시하여 제안된 기법의 성능을 검증한다.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2005년도 ICCAS
• /
• pp.265-270
• /
• 2005

This paper presents a new attitude stabilization and control of an unmanned helicopter based on neural network compensation. A systematic derivation on the dynamics of an unmanned small-scale helicopter is performed. Combined rotor-fuselage-tail dynamics is derived in body-fixed reference frame with its origin at the C.G. of the helicopter. And the resulting nonlinear equation of motion consists of 6-DOF air vehicle dynamics as well as the rotor flapping and engine torque equations. A simulation model was modified using the existing simulator for an unmanned helicopter dynamic model, which reflects the unmanned test helicopter(CNUHELI). The dynamic response of the refined model was compared with the flight test data. It can be shown that a good coincidence was accomplished between the real unmanned helicopter system and the mathematical model. This dynamic model was linearized for classical controller design using small perturbation method. A Neuro-PD control system was designed for both longitudinal and lateral flight modes, and the results were compared with the PD-only control response. Simulation results show that the proposed Neuro-PD control system demonstrates better performance.

• 기술사
• /
• 제34권4호
• /
• pp.69-73
• /
• 2001

Due to the rapid increase of automobiles and daily driving distances, air pollution by automobiles is still dominant problem of large city in spite of strict emission refutation and development of reduction technologies. Among the air pollution resources of automobile , industry. electricity generation and heating. automobile keeps 51% of total nationwide air pollution in 1998 and this proportion Is increasing in large cities from 65% to 85%. To reduce these air pollution. catalytic converter and electronic engine control, exhaust gas re-circulation and evaporative emission control system have continuously developed and applied to automobiles since 1987. Also strong emission standards and emission durability warranty have enforced and monitored annually by sampling several vehicle models. But technologies and regulations are incomplete, driver should participate in reducing air pollution for himself by planning driving, avoiding unnecessary idle and air conditioning, keeping periodic maintenance and using mass transportation.