• Transactions of the Korean hydrogen and new energy society
• /
• v.12 no.3
• /
• pp.169-176
• /
• 2001

The purpose of study is to obtain low-emission and high-efficiency in LPG engine with hydrogen enrichment. The test engine was named heavy-duty variable compression ratio single cylinder engine (VCSCE). The fuel supply system provides LPG/hydrogen mixtures based on same heating value. Various sensors such as crank shaft position sensor (CPS) and hall sensor supply spark timing data to ignition controller. Displacement of VCSCE is $1858.2cm^3$. VCSCE was runned 1400rpm with compression ratio 8. Spark timing was set MBT without knocking. Relative air-fuel ratio(${\lambda}$) of this work was varied between 0.76 and 1.5. As a result, i) Maximum thermal efficiency occurred at ${\lambda}$ value 1.0. It was shown that thermal efficiency was increased approximately 5% with hydrogen enrichment at same ${\lambda}$ value. ii) Engine-out carbon monoxide (CO) emissions were decreased at a great rate under LPG/hydrogen mixture fuelling. iii) Total hydrocarbon (THC) emission was much exhausted in rich zone, same as CO. But THC was exhausted a little bit more in lean zone. iv) Finally, engine-out oxides of nitrogen (NOx) was increased with ${\lambda}$ value 1.0 zone at a greater rate with hydrogen enrichment due to high adiabatic flame temperature.

• Journal of Advanced Marine Engineering and Technology
• /
• v.33 no.8
• /
• pp.1100-1106
• /
• 2009

Recently, there are quite a lot of attention is drown on the researches related to of Miller method applied high expansion cycle. For this study, high expansion cycles are formed and analyzed with the base view point of thermodynamics, and the features of each factors are also investigated. As a result of analysis, the expansion-compression ratio is expected with a decrease of effective compression ratio as intake valve closing time retarded, however, the decrease of mean effective pressure and its output is accompanied with the counterflow of intake air. Accordingly, as the consequence of such failure, it is expected that an alternative is needed for the realization of high expansion cycles, and the improvement over thermal efficiency. To materialize such cycle, the control system to delay the closing time of intake valve was designed and VVT, the 3 S/B low speed diesel engine, is applied to evaluate the efficiency. The result of the trial shows that there was no significant errors.

• Steel and Composite Structures
• /
• v.29 no.4
• /
• pp.451-464
• /
• 2018

This paper presents some quasi-static tests for 4 mixed columns composed of CFST column and RC column. The seismic performance and failure mode were studied under low-cyclic revised loading. The failure mode was observed under different axial compression ratios. The hysteretic curve and skeleton curve were obtained. The effects of axial compression ratio on yield mechanism, displacement ductility, energy dissipation, stiffness and strength attenuation were analyzed. The results indicate that the failure behavior of CFST-RC mixed column with archaized style is mainly caused by bending failure and accompanied by some shear failure. The axial compression ratio performs a control function on the yielding order of the upper and lower columns. The yielding mechanism has a great influence on the ductility and energy dissipation capacity of specimens. Based on the experiment, finite element analysis was made to further research the seismic performance by ABAQUS software. The variable parameters were stiffness ratio of upper and lower columns, axial compression ratio, yielding strength of steel tube, concrete strength and rebar ratio. The simulation results show that with the increase of stiffness ratio of the upper and lower columns, the bearing capacity and ductility of specimens can correspondingly increase. As the axial compression ratio increases, the ductility of the specimen decreases gradually. The other three parameters both have positive effect on the bearing capacity but have negative effect on the ductility. The results can provide reference for the design and engineering application of mixed column consisted of CFST-RC in Chinese archaized buildings.

• Transactions of the Korean hydrogen and new energy society
• /
• v.24 no.6
• /
• pp.472-479
• /
• 2013

A free piston linear engine could be operated under HCCI combustion due to its variable compression ratios. To obtain HCCI combustion, the free piston linear engine needs a high compression ratio to achieve auto-ignition of the fuel/air mixture. In this study, an idea for obtaining a high compression ratio using the transition from SI combustion to HCCI combustion was proposed. The fuel used in this study is hydrogen, which is considered to be an environmentally friendly fuel. Besides, the effects of key parameters such as equivalence ratio (${\phi}$), load resistance ($R_L$) and intake temperature ($T_{in}$) on the SI-HCCI transition were numerically investigated. The simulation results show that the SI-HCCI transition is successful without any significant reduction of in-cylinder pressure as the intake temperature is increased from $T_{in}$=300K (SI mode) to $T_{in}$=450K (HCCI mode), while the load resistance and equivalence ratio are retained respectively at $R_L=120{\Omega}$ and ${\phi}$=0.6 in both SI mode and HCCI mode.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2001.10a
• /
• pp.175-182
• /
• 2001

Effective length factor approach for framed column design has long played an important design-aid role. This approach, however, is effective only when the columns are in the form of prismatic or uniform cross sections. Structural engineers who have to design or analyse framed columns with variable cross sections need some means to do their job. By using the finite element method, the stability analysis of the isolated compression members with variable cross sections and that of the framed columns are performed. The parameters considered in the stability analysis are taper and sectional property parameters of the columns, the second moment of inertia ratio of beam to column, and beam span to column height ratio. On the basis of the stability analysis results, effective length factor formulas for the columns with variable sections are derived.

• Journal of Energy Engineering
• /
• v.15 no.3 s.47
• /
• pp.139-145
• /
• 2006

The purpose of this study is to obtain low-emission and high-efficiency in LPG engine with hydrogen enrichment. The objective of this paper is to clarify the effects of hydrogen enrichment in LPG fuelled engine on exhaust emission, thermal efficiency and performance. The compression ratio of 8 was selected to avoid abnormal combustion. To maintain equal heating value of fuel blend, the amount of LPG was decreased as hydrogen was gradually added. The relative air-fuel ratio was increased from 0.8 to 1.3, and the ignition timing was controlled to be at MBT (minimum spark advance for best torque)

• Transactions of the Korean Society of Automotive Engineers
• /
• v.10 no.1
• /
• pp.255-264
• /
• 2002

In this paper, the power transmitting mechanism for negative torque of the metal V-belt (MVB) CVT were investigated by theoretically analyzing variation of band tension, block compression forces for each of the primary and secondary pulleys. An experimental study was performed to investigate the speed ratio - thrust characteristics for negative torque. The experimental results are in good acoordance with the theoretical results. CVT line pressure control logic was suggested for negative torque based the speed radio - negative torque - thrust characteristics and the thrust ratio curves. The results of this study can be used as basic design materials for developing the CVT control system for negative torque.

• Journal of the korean Society of Automotive Engineers
• /
• v.7 no.4
• /
• pp.49-56
• /
• 1985

This study consists of instrumenting and running tests on variable compression engines and measuring the following combustion characterics: (a)flame speed, (b) emission and (c)performance parameter such as power and economy. The results were as follows: 1) The phase separation diagram of substitute fuels were obtained from phase separation experiment. 2) The flame propagation speed of substitute fuels were higher than gasoline and increased with increasing methanol weight percent of substitute fuels. 3) BEMP of substitute fuels was slightly less than that of gasoline but in the range of small weight percent, BEMP was compatible to gasoline. 4) Concentration of NOx decreased significantly with delaying spark advancing time. Also, it decreased for rich equivalence ratio but increased with high compression ratio. In general, NOx concentration was much lower than that of gasoline. 5) Concentration of HC and CO increased for rich equivalence ratio. Also it was lower than that of gasoline.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.19 no.2
• /
• pp.38-45
• /
• 2015

This paper describes an ejector design technique which used for simulating low pressure environment corresponding to high altitude. Also the ejector performance characteristics was investigated according to performance and geometric variables by cold gas flow test. Entrainment ratio, compression ratio and expansion ratio were designated as performance variables and an ejector gap ratio was designated as a geometric variable. A relationship between the performance variables to predict the ejector performance was identified and it was confirmed that the performance variables have much more effective than the ejector gap ratio through the ejector cold gas flow test.

• Journal of the Korean Institute of Telematics and Electronics B
• /
• v.33B no.4
• /
• pp.63-71
• /
• 1996

In this paper, a variable length block code for real time compression and decompression of hanguel and chinese character bit map font is proposed. The proposed code shows a good compression ratio in complete form of hangeul myoungjo and godik style and chinese batang and doddum style bit map font. Besides, a compression and decompression ASIC is designed and simulated on CAD. The 0.8 micron CMOS sea of gate is used to implement the ASIC in amount of 5,200 gates, and it runs at simple hardware and compress and decompress at 33M bit/sec at maximum, which is ideal for real time applications.