• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2004.04a
• /
• pp.299-303
• /
• 2004

In this paper, it is presented a level sensor for measuring a level of the contents of cargo tank using frequency modulated continuous wave(FMCW). The frequency range is 10∼11 GHz, the radar cross section(RCS) of target is 0.8 ㎡ of metal plate. the experiment is performed in laboratory and open ground, the sweep time of the signal is 100 ms, the pyramidal horn antenna of about 20 dBi gain is used, and input power of antenna is about 5 dBm. the beat frequency according to the target moving to 40 m is measured. There is a good agreement between measured and calculated results. But the resolution of the FMCW radar is measured about 10 cm due to nonlinear of voltage controlled oscillator(VCO).

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.19 no.9
• /
• pp.1692-1701
• /
• 1994

Macromodeling technology is useful to simulate and analyze the performance of new elements and complicated circuits or systems without any changes in today's general simulator, PSPICE. In this paper, Phase Locked Loop(PLL) is designed using macromodeling technique. The PLL macromodel has two basic sub-macromodels of the phase detector and the voltage controlled oscillator(VCO). The PLL macromodel has two open terminals for inserting RC low pass filter. The PLL macromodel is simulated using simulation parameters of LM565CN manufactured in the National company. At a free-running frequency, 2500Hz, upper lock range and lower capture range was 437Hz, 563Hz, respectively. Also, experimental results and simulation results of LM565CN PLL show good agreement.

• Journal of the Optical Society of Korea
• /
• v.16 no.3
• /
• pp.288-291
• /
• 2012

We designed an ultra-wide band-pass filter applicable to microwave reflectometry for KSTAR (Korea Superconducting Tokamak Advanced Research) and to microwave photonics. The proposed ultra-wide band-pass filter exhibits a metamaterial structure characterized by a wide band, low insertion loss, and high skirt selectivity. The proposed filter is applied to enhance the linearity of reflectometry at the output of a VCO (voltage controlled oscillator). The pass-band of the proposed filter is observed at 18~28 GHz, and the out-of-band rejection is below 20 dB. Further, we constructed an unwrapped negative phase of S(2, 1) to verify the characteristics of the metamaterial. The under- and upper-band at lower limits of the pass-band are left- and right-handed, respectively. The group delay of the filter is less than 0.5 ns.

• 한국정보통신설비학회:학술대회논문집
• /
• 2005.08a
• /
• pp.159-165
• /
• 2005

The proposed optical transmitter is composed of FF(flip flop) , PLL (phase locked loop), reference clock generator, serializer and LD driver 10x250 Mb/s data arrays are translated to the 2.5 Gb/s data signal by serializer. In this case, 1 data bus is allocated usually as a reference clock for synchronization. In this proposed optical transmitter, 125 MHz reference clock is generated from 10x250 Mb/s data arrays by reference clock generator. From this method. absent of reference clock bus is available and more data transmission become possible. To achieve high speed operation, the serializer circuit is designed as two stacks. For 10:1 serialization, 10 clocks that have 1/10 lambda differences is essential, so the VCO (voltage controlled oscillator) composed of 10 delay buffers is designed. PLL is for runing at 250 MHz, and dual PFD(phase frequency detector) is adopted for fast locking time. The optical transmitter is designed by using 0.35 um CMOS technology.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.15 no.12 s.91
• /
• pp.1161-1167
• /
• 2004

The conventional PLL(phase locked loop) frequency synthesizer takes a long switching time because of the inherent closed-loop structure. The digital hybrid PLL(DH-PLL) which includes the open-loop structure into the conventional PLL synthesizer has been studied to overcome this demerit. It operates in high speed, but the hardware complexity and power consumption are the serious problem because the DLT(digital look-up table) is usually implemented by the ROM which contains the transfer characteristic of VCO(voltage controlled oscillator). This paper proposes a new DH-PLL using a very simple DLT-replacement digital logic instead of the complex ROM-type DLT. Also, a timing synchronization circuit for the very small over-shoot and shorter settling time is designed for the ultra fast switching speed at every frequency synthesis. The hardware complexity gets decreased to about $28\%,$ as compared with the conventional DH-PLL. The high speed switching characteristic of the frequency synthesis process can be verified by the computer simulation and the circuit implementation.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.12 no.1
• /
• pp.1-6
• /
• 2019

An extremely small size multi-loop phase-locked loop(PLL) keeping phase noise performances has been proposed. It has been designed to have the loop filter made of small single capacitor with multiple Frequency Voltage Converters (FVCs) because the main goal is to make the size of the proposed PLL extremely small. Multiple FVCs which are connected to voltage controlled oscillator(VCO) make multiple negative feedback loops in PLL. Those multiple negative feedback loops enable the PLL with the loop filter made of an extremely small size single capacitor operate stably. It has been designed with a 1.8V $0.18{\mu}m$ CMOS process. The simulation results show that the proposed PLL has the 1.6ps jitter and $10{\mu}s$ locking time.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.42 no.7 s.337
• /
• pp.35-40
• /
• 2005

This paper proposes a fractional-N phase-locked loop (PLL) frequency synthesizer using the 3rd order ${\Delta}{\sum}$ modulator for 900MHz medium speed wireless link. The LC voltage-controlled oscillator (VCO) is used for the good phase noise property. To reduce the lock-in time, a charge pump has been developed to control the pumping current according to the frequency steps and the reference frequency is increased up to 3MHz. A 36/37 fractional-N divider is used to increase the reference frequency of the phase frequency detector (PFD) and to reduce the minimum frequency step simultaneously. A 3rd order ${\Delta}{\sum}$ modulator has been developed to reduce the fractional spur VCO, Divider by 8 Prescaler, PFD and Charge pump have been developed with 0.25um CMOS, and the fractional-N divider and the third order ${\Delta}{\sum}$ modulator have been designed with the VHDL code, and they are implemented through the FPGA board of the Xilinx Spartan2E. The measured results show that the output power of the PLL is about -lldBm and the phase noise is -77.75dBc/Hz at 100kHz offset frequency. The minimum frequency step and the maximum lock-in time are 10kHz and around 800us for the maximum frequency change of 10MHz, respectively.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• v.2
• /
• pp.385-390
• /
• 2006

This paper examines the sampling and jitter specifications and considerations for Global Navigation Satellite Systems (GNSS) software receivers. Software radio (SWR) technologies are being used in the implementation of communication receivers in general and GNSS receivers in particular. With the advent of new GPS signals, and a range of new Galileo and GLONASS signals soon becoming available, GNSS is an application where SWR and software-defined radio (SDR) are likely to have an impact. The sampling process is critical for SWR receivers, where it occurs as close to the antenna as possible. One way to achieve this is by BandPass Sampling (BPS), which is an undersampling technique that exploits aliasing to perform downconversion. BPS enables removal of the IF stage in the radio receiver. The sampling frequency is a very important factor since it influences both receiver performance and implementation efficiency. However, the design of BPS can result in degradation of Signal-to-Noise Ratio (SNR) due to the out-of-band noise being aliased. Important to the specification of both the ADC and its clocking Phase- Locked Loop (PLL) is jitter. Contributing to the system jitter are the aperture jitter of the sample-and-hold switch at the input of ADC and the sampling-clock jitter. Aperture jitter effects have usually been modeled as additive noise, based on a sinusoidal input signal, and limits the achievable Signal-to-Noise Ratio (SNR). Jitter in the sampled signal has several sources: phase noise in the Voltage-Controlled Oscillator (VCO) within the sampling PLL, jitter introduced by variations in the period of the frequency divider used in the sampling PLL and cross-talk from the lock line running parallel to signal lines. Jitter in the sampling process directly acts to degrade the noise floor and selectivity of receiver. Choosing an appropriate VCO for a SWR system is not as simple as finding one with right oscillator frequency. Similarly, it is important to specify the right jitter performance for the ADC. In this paper, the allowable sampling frequencies are calculated and analyzed for the multiple frequency BPS software radio GNSS receivers. The SNR degradation due to jitter in a BPSK system is calculated and required jitter standard deviation allowable for each GNSS band of interest is evaluated. Furthermore, in this paper we have investigated the sources of jitter and a basic jitter budget is calculated that could assist in the design of multiple frequency SWR GNSS receivers. We examine different ADCs and PLLs available in the market and compare known performance with the calculated budget. The results obtained are therefore directly applicable to SWR GNSS receiver design.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.25 no.4B
• /
• pp.613-623
• /
• 2000

Digital TV tuner for 8-VSB modulation was developed with satisfying the requirements of ATSC. The double frequency conversion and the active tracking filter in the front-end were used to reduce interference of the adjacent channels and multi-channels, which suppress If beat and image band. However, it was impossible to get frequency mapping between tracking filter and first VCO(Voltage Controlled Oscillator) in the double conversion digital TV tuner differing from conventional NTSC tuner. This paper, therefore, suggests the available structure and a new method for automatic frequency selection by obtaining the mapping of frequency characteristic over tracking voltage and the combined hardware which compose of Micro-controller, EEPROM, D/A(Digital-to-Analog Converter), OP amp and switch driver to solve above problems.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.15 no.4
• /
• pp.506-517
• /
• 2015

This paper presents a 1.248 Gb/s - 2.918 Gb/s low-power receiver MIPI-DigRF M-PHY with a fully digital frequency detection loop. MIPI-DigRF M-PHY should be operated in a very short training time which is $0.01{\mu}s$ the for HS-G2B mode. Because of this short SYNC pattern, clock and data recovery (CDR) should have extremely fast locking time. Thus, the quarter rate CDR with a fully digital frequency detection loop is proposed to implement a fast phase tracking loop. Also, a low power CDR architecture, deserializer and voltage controlled oscillator (VCO) are proposed to meet the low power requirement of MIPI-DigRF M-PHY. This chip is fabricated using a $0.11{\mu}m$ CMOS process, and the die area is $600{\mu}m{\times}250{\mu}m$. The power consumption of the receiver is 16 mW from the supply voltage of 1.1 V. The measured lock time of the CDR is less than 20 ns. The measured rms and peak jitter are $35.24ps_{p-p}$ and $4.25ps_{rms}$ respectively for HS-G2 mode.