• Proceedings of the IEEK Conference
• /
• 2004.06b
• /
• pp.465-468
• /
• 2004

In this paper, we describe the design and implementation of the new current-current negative feedback (CCNF) voltage-controlled oscillator (VCO), which suppresses 1/f induced low-frequency noise. By means of the CCNF, the high-frequency noise as well as the low-frequency noise is prevented from being converted into phase noise. The proposed CCNF VCO shows 11-dB reduction in phase noise at 10 kHz offset, compared with the conventional differential VCO. The phase noise of the proposed VCO is -87 dBc/Hz at 10 kHz offset frequency from 5.5-GHz carrier. The proposed VCO consumes 14.0 mA at 2.0 V supply voltage, and shows single-ended output power of -12.0 dBm.

• Journal of Electrochemical Science and Technology
• /
• v.8 no.4
• /
• pp.314-322
• /
• 2017

The electrolyte plays one of the most significant roles in the performance of electrochemical supercapacitors. Most liquid organic electrolytes used commercially have temperature and potential range constraints, which limit the possible energy and power output of the supercapacitor. The effect of elevated temperature on a lithium bis(oxalate)borate(LiBOB) salt-based electrolyte was evaluated in a symmetric supercapacitor assembled with activated carbon electrodes and different electrolyte blends of acetonitrile(ACN) and propylene carbonate(PC). The electrochemical properties were investigated using linear sweep voltammetry, cyclic voltammetry, galvanostatic charge-discharge cycles, and electrochemical impedance spectroscopy. In particular, it was shown that LiBOB is stable at an operational temperature of $80^{\circ}C$, and that, blending the solvents helps to improve the overall performance of the supercapacitor. The cells retained about 81% of the initial specific capacitance after 1000 galvanic cycles in the potential range of 0-2.5 V. Thus, LiBOB/ACN:PC electrolytes exhibit a promising role in supercapacitor applications under elevated temperature conditions.

• 한국연소학회:학술대회논문집
• /
• 2014.11a
• /
• pp.81-84
• /
• 2014

A Experimental study on flame extinction behavior was investigated using He curtain flow with counter triple co-flow burner. Buoyancy force was suppressed up to a microgravity level of $10^{-2}-10^{-3}g$ by using He curtain flow. The stability maps were provided with a functional dependency of diluent mole fraction and global strain rate to clarify the differences in flame extinction behavior. The flame extinction curves had C-shapes at various global strain rates. The oscillation and extinction modes were different each other in terms of the global strain rate, and the flames extinction modes could be classified into five modes such as (I) and (II): an extinction through the shrinkage of the outmost edge flame forward the flame center after self-excitation and without self-excitation, respectively, (III): an extinction through rapid advancement of a flame hole while the outmost edge flame is stationary, (IV): self-excitation occurs in the outermost edge flame and the center edge flame and then a donut shaped flame is formed and/or the flame is entirely extinguished, (V): shrinkage of the outermost edge flame without self-excitation followed by shrinkage or survival of the center flame. These oscillation and extinction modes could be identified well to the behavior of edge flame. The result also showed that the edge flame was influenced significantly by the conductive heat losses to the flame center or ambient He curtain flow.

• Journal of The Korean Astronomical Society
• /
• v.37 no.5
• /
• pp.455-460
• /
• 2004

There have been many speculations about the presence of cosmic ray protons (CRps) in galaxy clusters over the past two decades. However, no direct evidence such as the characteristic $\gamma$-ray signature of decaying pions has been found so far. These pions would be a direct tracer of hadronic CRp interactions with the ambient thermal gas also yielding observable synchrotron and inverse Compton emission by additionally produced secondary electrons. The obvious question concerns the type of galaxy clusters most likely to yield a signal: Particularly suited sites should be cluster cooling cores due to their high gas and magnetic energy densities. We studied a nearby sample of clusters evincing cooling cores in order to place stringent limits on the cluster CRp population by using non-detections of EGRET. In this context, we examined the possibility of a hadronic origin of Coma-sized radio halos as well as radio mini-halos. Especially for mini-halos, strong clues are provided by the very plausible small amount of required CRp energy density and a matching radio profile. Introducing the hadronic minimum energy criterion, we show that the energetically favored CRp energy density is constrained to $2\%{\pm}1\%$ of the thermal energy density in Perseus. We also studied the CRp population within the cooling core region of Virgo using the TeV $\gamma$-ray detection of M 87 by HEGRA. Both the expected radial $\gamma$-ray profile and the required amount of CRp support this hadronic scenario.

• Korean Journal of Materials Research
• /
• v.19 no.11
• /
• pp.619-624
• /
• 2009

Titanium alloys have been attractive due to a high ratio of strength to weight as well as good corrosion resistance. However, strengthening causes a decrease in ductility in Ti alloys, as is usual in other alloys. For enhanced strength without ductility reduction, grain refinement and tensile properties were investigated as functions of thickness reduction of cold rolling and annealing condition in Ti-15V-3Cr-3Sn-3Al alloy with a ${\beta}$ single phase. The average grain size of the specimen, which was cold-rolled by 90% and annealed at 700$^{\circ}C$ for 5 min, was decreased to approximately 19 ${\mu}m$. The grain refinement of 63 μm to 19 ${\mu}m$ increased yield stress by 90 MPa without a significant decrease in total elongation. The Ti-15-3 alloy exhibited very low work hardening during tensile test at a crosshead speed of 2 mm/min. This result was discussed based on dynamic recovery associated with dislocation annihilation in grain boundaries.

• Proceedings of the KIEE Conference
• /
• 1991.11a
• /
• pp.299-303
• /
• 1991

A lamp heated LPCVD equipment has been made. Wafer is heated by an array of fifteen tungsten halogen lamps above the front side of a wafer and pyrometer views the back side of the wafer through $CaF_2$ window. Reactor which consisits of a quartz window and a water cooled-stainless steel plate can be evacuated to $5{\times}10^{-3}$ torr with a rotary vane pump. By pyrolysis of $SiH_4$ at about $600^{\circ}C$, polysilicon has been formed on the silicon dioxide film. The measured results show that thickness nonuniformity is 15% and temperature nonuniformity is 1.1%. Because activation energy of pyrolysis of $SiH_4$ is very high, about 1.8eV, small temperature variation will induce large thickness nonuniformity. The main cause of temperature nonuniformity is unsymmetry of lamp power and an unbalanced cooling structure. Charls & Evans' SIMS result shows that the oxygen content in the deposited polysilicon is comparable to that of silicon substrate but carbon content is ten times higher.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.56 no.9
• /
• pp.1596-1601
• /
• 2007

Aluminum doped zinc oxide (AZO) thin films were deposited on coming glass substrates using an Nd:YAG pulsed laser deposition technology. The AZO thin films were deposited with various growth conditions such as the substrate temperature and oxygen partial pressure. In this work, we used various measurement technologies in order to investigate the electrical, structural, and optical properties of the AZO thin films. Among the AZO thin films, the one prepared at the substrate temperature of $300^{\circ}C$ and oxygen partial pressure of 5 mTorr showed the best properties of an electrical resistivity of $4.63{\times}10^{-4}{\Omega}{\cdot}cm$, a carrier concentration of $9.25{\times}10^{20}cm^{-3}$, and a carrier mobility of $31.33cm^2/V{\cdot}s$. All the AZO thin films showed an high average optical transmittance over 90 % in visible region.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.38 no.5
• /
• pp.1-1
• /
• 2001

비휘발성 메모리 소자로의 응용의 관점에서, sol-gel 방법으로 La 을 10mo1% 로 고정시킨 PLZT (10/y/z) 박막을 제작하여 Zr/Ti 조성비에 따른 구조적 및 전기적 특성을 조사하였다. PLZT(10/40/60) 박막은 로제트와 파이로클로르 상이 관찰되었으며, Zr/Ti 조성비에서 Ti 함유량이 증가함에 따라, (100) 배향성, 결정립 크기와 표면 거칠기는 증가되었다. 또한 Zr/Ti 조성비에서 Ti 함유량이 증가함에 따라, 10㎑ 에서 비유전율은 600 에서 400 으로 감소된 반면, 유전손실은 0.028 에서 0.053 로 증가되었으며, 170 ㎸/cm 에서 누설전류밀도는 1.64×$10^{-6}$ 에서 1.26×$10^{-7}$A/㎠ 으로 감소되었다. 그리고 ± 170㎸/㎝ 에서 측정한 PLZT 박막의 이력곡선을 측정한 결과, Zr/Ti 조성비가 40/60 에서 0/100 로 변화함에 따라 PLZT 박막의 잔류분극과 항전계는 6.62 에서 12.86 μC/cm2, 32.15 에서 56.45㎸/㎝ 로 각각 증가되었으며, 피로와 retention 특성 역시 개선되었다. PLZT 박막에 ±5V 의 사각펄스를 $10^9$ 회 인가하여 피로특성을 측정한 결과, PLZT(10/40/60) 박막의 잔류분극은 초기분극값으로부터 50% 감소된 반면, PLZT(10/0/100) 박막은 30% 감소되었다. 또, $10^5$ 초의 retention 결과에서 PLZT(10/0/100) 박막은 초기분극값에서 오직 11% 만이 감소된 반면, PLZT(10/40/60) 박막은 40% 감소되었다.

• Proceedings of the KIEE Conference
• /
• 1997.07f
• /
• pp.2249-2251
• /
• 1997

Total 144 quadrupole magnets are installed in PLS. The magnets are connected in series with groups of two or 24. Each group is powered by a high-precision constant-current DC power supply. For the purpose of the beam based alignment of beam position monitors in the PLS, it is necessary to adjust the current of each quadrupole independently. To achieve this, a high current shunt regulator is designed. It can shunt a maximum 50 A of the quadrupole magnet current. The shunt regulator is programmable and the current amplitude can be varied linearly with a 12-bit resolution. Power transistors are used in the current shunt regulator. The operation of transistors is in linear region. The RS232C protocol is used for remote control and status report of the shunt regulator to the main control centre of the PLS. Preliminary result indicates that the calibration accuracy of the beam position monitor can be achievable in less than $10{\mu}m$.

• Journal of ILASS-Korea
• /
• v.1 no.2
• /
• pp.16-23
• /
• 1996

In case of a high-speed D.I. diesel engine. the injected fuel spray is unavoidable that the impinging on the wall of piston cavity and in this case the geometry of piston cavity has a great influence on the atomization structure and air flow fields. In the field of combustion and in many other spray applications, there are clear evidence of correlation between spray structure and emission of pollutants. Ordinary, the combustion chamber of driving engine have unsteady turbulent flow be attendant on such as the change of temperature, velocity and pressure. So the analysis of spray behavior is difficult. In this study, a single spray was impinged on each cavity wall at indicated angle in a quiescent atmosphere at room temperature and pressure, as being the simplest case, and 3 types of piston cavity such as Dish, Toroidal and Re-entrant type was tested for analyzing the influence of cavity geometry. And hot wire probe was used for analyze non-steady flow characteristics of impinging spray, and to investigate the behavior of spray, the aspects of concentration c(t), standard deviation $\sigma(t)$ and variation factor (v.f.) was measured with the lapse of time.