• Journal of radiological science and technology
• /
• v.26 no.3
• /
• pp.19-24
• /
• 2003

We carried out studies on development and characteristic of ultrasound brast training biopsy phantom. the major finding were of follow ; (1) C type TMM was shown good homogeneity, brightness and attenuation as like human soft tissue. (2) $TiO_2$ 4.10%w/v TMM was shown good homogeneous echo texture and propagated speed as like the human Tissue. (3) $TiO_2$ type TMM was appeared lower brightness and higher penetration rate than C type TMM. Therefor, Breast TM phantom and target material TMM will be useful $TiO_2$ 4.10 %w/v TMM and C 2.09 %w/v TMM.

• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2002.10a
• /
• pp.307-311
• /
• 2002

This study was investigated the photoelectrochemical behavior of STS304 steel with $TiO_2$ thin films coating, applied by sol-gel method, for the purpose of cathodic photoprotection of the steel corrosion. One time $TiO_2$-coated STS304 steel adopted two kinds of $TiO_2$ sol solution has the most dominant photopotential abilities, which was -200mV vs. SCE and -500mV vs. SCE under illumination with 40W fluorescent lamp, respectively. That was more negative than the corrosion potential of the bare metal(-150 mV). The bleaching of TCE was confirmed on $TiO_2$-coated STS304 under UV-illumination with 20 W Black-light. This Study was concluded that $TiO_2$-coated STS304 exhibited both a cathodic photoprotection effect against corrosion and photocatalytic self-cleaning effect.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2011.05a
• /
• pp.187-187
• /
• 2011

지르코니아 ($ZrO_2$) 표면에 금속 (Au)으로 표면 코팅한 후 Ti-6Al-4V와 진공 브레이징 접합을 행하였다. 표면에 코팅한 Au 층의 영향을 비교 분석하기 위하여 Au를 코팅하지 않은 지르코니아도 모재로 사용하였다. 접합소재로는 Ag-Cu-Ti계 active filler를 사용하였다. $ZrO_2$/Ti-6Al-4V 브레이징 결과, active filler는 양측 모재 표면에 wetting 되었으며, Ti-6Al-4V 내부로 filler 확산으로 인하여 두 모재의 direct joint가 관찰되었다. 접합 계면 사이에 접합부 결함은 관찰되지 않았다.

• Korean Journal of Materials Research
• /
• v.18 no.1
• /
• pp.22-25
• /
• 2008

In this study, calcium titanate $(CaTiO_3)$ gel was prepared by mixing calcium nitrate and titanium isopropoxide in 2-methoxy-ethanol. $CaTiO_3$ gel was single-layer coated on Ti-6Al-4V using a sol-gel dip-coating technique. The coating was calcined at $750^{\circ}C$ in air by utilizing a very slow heating rate of $2^{\circ}C/min$. The crystalline phases of the coating were characterized by x-ray diffraction using a slow scan rate of $1^{\circ}/min$. The morphology of the coating was analyzed by scanning electron microscopy. The corrosion behavior of Ti-6Al-4V samples coated with $CaTiO_3$ films were tested in an artificial saliva solution by potentiodynamic polarization and were quantified by the Tafel extrapolation method. The electrochemical parameters showed a considerable increase in the corrosion resistance for the $CaTiO_3$-coated Ti-6Al-4V samples compared to bare substrates.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1996.11a
• /
• pp.75-78
• /
• 1996

The deposition condition Gf TiN films as electrode was studied by sheet resistance, TiN depositon Thickness X-ray diffraction. TiN was made by reactively DC magnetron sputtering with varying $N_2$/Ar mixture gas and substrate temperature. After finding The deposition condition of TiN films, The samples with the structure of Cu/Ta$_2$O$_{5}$, TiN/Ta$_2$O$_{5}$Si, Cu/TiN/Ta$_2$O$_{5}$ Si were prepared and were measured I-V, C-V. As a results, it was found that when TiN was deposited in an $N_2$a results, it was found that when TiN was deposited in an $N_2$atmosphere its Sheet resistance is lower n than n V$_2$Ar mixtureixture

• Applied Chemistry for Engineering
• /
• v.28 no.5
• /
• pp.576-580
• /
• 2017

In the present paper, the thermal deactivation characteristics of plate-type commercial $V_2O_5-WO_3/TiO_2$ SCR catalyst were investigated. For this purpose, the plate-type catalyst was calcined at different temperatures ranging from $500^{\circ}C$ to $800^{\circ}C$ for 3 hours. Structural and morphological changes were characterized byXRD, specific surface area, porosity, SEM-EDS and also NOx conversion with ammonia according to the calcine temperature. The NOx conversion decreased with increasing calcine temperature, especially when the catalysts were calcined at temperatures above $700^{\circ}C$. This is because the crystal phase of $TiO_2$ changed from anatase to rutile, and the $TiO_2$ grain growth and $CaWO_4$ crystal phase were formed, which reduced the specific surface area and pore volume. In addition, $V_2O_5$, which is a catalytically active material, was sublimated or vaporized over $700^{\circ}C$, and a metal mesh used as a support of the catalyst occurred intergranular corrosion and oxidation due to the formation of Cr carbide.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.534-534
• /
• 2013

본 연구에서는 RF/DC 마그네트론 스퍼터링 시스템을 이용하여 co-sputtering 방법으로 TiO2와 ZnO를 이용하여 인버티드 유기태양전지용 버퍼층을 제작하고 TiO2와 ZnO의 함량에 따른 인버티드 유기 태양전지 특성을 비교하였다. Ti-Zn-O 버퍼층은 기존의 버퍼층 제작에 사용되던 용액 공정 대신 스퍼터링 시스템을 이용하여 제작하였다. ITO 전극 상부에 곧바로 Ti-Zn-O를 성막하여 Anode와 버퍼층이 일체화된 투명 전극을 제작하고 ZnO와 TiO2 함량이 유기 태양전지의 특성에 미치는 영향을 연구하였다. 버퍼층의 TiO2와 ZnO 함량에 따른 광학적, 구조적특성을 UV/Vis spectrometry와 X-ray diffraction (XRD), TEM 등으로 분석하였으며, Ti-Zn-O 박막의 실제 버퍼 층으로서의 적용 가능성을 알아보기 위해 인버티드 유기태양전지로 제작하여 그 특성을 평가하였다. 기존의 인버티드 유기태양전지의 특성이 fill factor of 55.58%, short circuit current of 8.33 mA/cm2, open circuit voltage of 0.66 V, efficiency 3.06%인데 반해 최적 조건의 Ti-Zn-O 버퍼층을 적용했을 경우 fill factor of 52.05%, short circuit current of 8.81 mA/cm2, open circuit voltage of 0.66 V, efficiency 3.03%인 우수한 유기태양전지의 특성을 보임으로써 스퍼터링 공법으로 제작된 Ti-Zn-O 박막의 인버티드 유기태양전지용 버퍼 층으로서의 적용 가능성을 확인하였다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.11a
• /
• pp.321-324
• /
• 2003

The effects of various sintering additives such as $Bi_2O_3+V_2O_5$, $BiVO_4$, $B_2O_3$, and $CuO+V_2O_5$ on the low-temperature sintering and microwave dielectric properties of $(ZnMg)TiO_3$ system were studied. Sintering was enhanced by the sintering additives and highly dense samples were obtained for $(Zn_{0.8}Mg_{0.2})TiO_3$ at the sintering temperature of $910^{\circ}C$. $(Zn_{0.8}Mg_{0.2})TiO_3$ with 6.19 mol.%$B_2O_3$ was found to show the best sintering and microwave dielectric properties.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.13 no.6
• /
• pp.272-278
• /
• 2003

$Bi_4Ti_3O_{12}$ (BIT) and $(Bi_{3.25}La_{0.75})(Ti_{2.97}V_{0.03})O_{12}$ (BLTV) thin films were deposited on ITO/glass substrates by metal organic chemical vapor deposition (MOCVD) using ultrasonic spraying. After deposition of the films in oxygen atmosphere for 30 min, the films were heated by rapid thermal annealing (RTA) method, especially direct insertion, at various temperatures. The films were investigated on phase formation temperature, microstructure and electrical properties. From x-ray diffraction (XRD) patterns, the perovskite phase formation temperature of BLTV thin film was about $600^{\circ}C$ which was lower than that of BIT, $650^{\circ}C$. The leakage current of the BLTV thin film was measured to be $1.52\times 10^{-9}$A/$cm^2$ at an applied voltage of 1 V. The remanent polarization (Pr) and coercive field (Ec) values of the BLTV film deposited at $650^{\circ}C$ were $5.6\muC/cm^2$ and 96.5 kV/cm, respectively.

• Journal of the Korean institute of surface engineering
• /
• v.56 no.6
• /
• pp.380-385
• /
• 2023

In this study, an MPB PMNT system containing 0.05 to 0.10 wt.% BaTiO₃ was synthesized using a traditional chemical method and its pyroelectricity was investigated. Pyroelectricity, dielectricity, and ferroelectricity of the synthesized BaTiO₃-PMNT system were analyzed by heat treatment at 1240~1280 ℃ for 4 hours to evaluate its applicability as a pyroelectric sensor. Unlike the simple ABO₃ ferroelectric, the BaTiO₃-doped PMNT system exhibited phase transition characteristics over a wide temperature range typical of complex perovskite structures. Although no dramatic change could be confirmed depending on the amount of BaTiO₃ added, stable pyroelectricity was maintained near room temperature and over a wide temperature range. When the amount of BaTiO₃ added increased from 0.05BaTiO₃-PMNT to 0.10BaTiO₃-PMNT, the electric field slightly increased from 5.00×10³ kV/m to 6.75×10³ kV/m, and the maximum value of remanent polarization slightly increased from 0.223 C/m² to 0.234 C/m². The pyroelectric coefficients of 0.05BaTiO₃-PMNT and 0.10BaTiO₃- PMNT at room temperature were measured to be ~0.0084 C/m²K and ~0.0043 C/m²K, respectively. The relaxor ferroelectric properties of the BaTiO₃-PMNT system were confirmed by analyzing the plot of K_max/K versus (T-T_max)^γ. The BaTiO₃-doped MPB PMNT system showed a distinct pyroelectric performance index at room temperature, and the values were F_v ~ 0.0362 m²/C, F_d ~ 0.575×10^-4 Pa^-1/2.