• Journal of the Korean Institute of Gas
• /
• v.12 no.4
• /
• pp.63-68
• /
• 2008

This paper describes about the simulation and the experimental results of optical cavity with curved mirror surface and vertical mirror surface to improve the light intensity and efficiency of the optical sensors. When we use the vertical mirror surface, the distribution of light reached to the filter surface of detector shows an elliptical shape. Whereas, the curved mirror surface focuses the light into circular shape. Therefore, due to focusing effects in case of using curved mirror surface, the light intensity per unit area has been improved. Consequently, the output voltage of gas sensor has been expected to increase. Based upon the simulation, the experiment of gas sensor has been conducted with $CO_2$ gas from 0ppm to 2,500 ppm at 250 ppm step and $25^{\circ}C$, 45%R.H. ambient. The output voltage of gas sensor that has a curved mirror surface increases approximately 200 mV than that of vertical mirror surface.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.44 no.8
• /
• pp.641-648
• /
• 2016

In this study, the effect of injection nozzle shape on the supersonic film cooling performance is analyzed using CFD. The design parameters are inside and outside angles of upper plate of nozzle and nozzle tip thickness. It is observed that the mass flow rate of film cooling decreases with increase of inside angle, while the effect of the change of mass flow rate on the film cooling effectiveness is relatively small. In addition, cooling performance is generally reduced, except ahead of the local region where shock wave interaction with film cooling occurs, in accordance with the growth of the outside angle and tip thickness. In this paper, the CFD simulation is performed using a commercial software, ANSYS Fluent V15.0, and the CFD model is validated by comparing it with the experimental data shown in preceding research.

• Animal cells and systems
• /
• v.2 no.4
• /
• pp.477-481
• /
• 1998

Previous studies have postulated that isometric animals exert similar locomotory capacity (speed, distance) because the amount of energy available for the motion would be the same regardless of body mass (m). To test propriety of this theory, we examined body shape and take-off potential of two frog species, Rana nigromaculata (powerful jumpers) and Bombina orientalis (slow hoppers). Morphological measurements included thigh muscle mass (indicative of total muscle force), hindlimb length (L, determining acceleration distance), and interilial width (shaping take-off motion). To gauge locomotory capacity, take-off speed (v) and take-off angle ($\theta$) were measured from video analyses, and jump distance (R) and take-off Power ($P_{t}$ ) were calculated from equations $R=V^{2}sin2\theta/g$ and ($P_{t}$＝$㎷^{3}/2L$(where g is the gravitational constant). Scaling exponents of morphometric variables for both species were 0.96-1.11 for thigh muscle mass, 0.28-0.29 for hindlimb length, and 0.30-0.36 for interilial width. Scaling exponents of locomotory performance for the two species were -0.01-0.14 for take-off speed, 0.24-0.31 for jump distance, and 0.66-0.84 for take-off power. The results demonstrate that the frogs of this study showed isometric body shape within species, but that take-off response changed allometrically with body mass, indicating that these data did not fully support the previous proposition. An exception was found in take-off speed of B. orientalis, in which the speed changed little with body mass (slope＝-0.01). These findings suggest that the energy availability approach did not properly explain the apparent allometric relations of the take-off response in these animals and that an alternative model such as a power production approach may be worth addressing.

• Korean Journal of Plant Taxonomy
• /
• v.32 no.4
• /
• pp.481-489
• /
• 2002

Unrecorded fern species of Korean flora, Thelypteris interrupta (Willd.) K. Iwats. (Thelypteridaceae) and Dryopteris subexaltata (H. Christ) C. Chr. (Dryopteridaceae), were collected from Jeju island off the south coast of Korean peninsula and reported here. T. interrupta is most similar to T. acuminata (Houtt.) C. V. Morton in morphology, however, the two species are readily distinguishable by the plant color including rhizome, stipe base and spore, and the presence of glandular hair as well as the distribution pattern of sorus on lower leaf surface. D. subexaltata is also well distinguishable from its relatives, D. sparsa (D. Don) Kuntze, D. sabaei (Franch. & Sav.) C. Chr., and D. yakusilvicola Sa. Kurata by the presence of proliferation, shape of pinnae, distribution pattern of sori on lower leaf surface, and shape of indusium.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.4 no.2
• /
• pp.157-168
• /
• 1994

The surface morphology, electrical properties, and optical properties of textured $SnO_2(:F)$ films according to deposition parameters such as HF and $H_2O$ content was studies. The electron concentration, resistivity, and mobility was $3{\Times}10^{20}/cm^3$, $7{\Times}10^4~9{\Times}10^4{Omega}cm$ and $18~25cm^2/V.sec$, respectively, when HF bubbling rate over 0.9 slm. The surface morphology was sharp edged pyramid shape without bubbling $H_2O$ but changed to round edged hemispherical shape when $H_2O$ was added.

• Korean Chemical Engineering Research
• /
• v.47 no.1
• /
• pp.72-78
• /
• 2009

For the electro-discharge machining of an electro-conductive anisotropic composite, an unsteady state formulation was established and solved by Galerkin's finite element method. The distribution of temperature on work piece, the shape of the crater and the material removal rate were obtained in terms of the process parameters. The $12{\times}12$ irregular mesh that was chosen as the optimum in the previous analysis was used for computational accuracy and efficiency. A material having the physical properties of alumina/titanium carbide composite was selected and an electricity with power of 51.4 V and current of 7 A was applied, assuming the removal efficiency of 10 % and the thermal anisotropic factors of 2 and 3. As the spark was initiated the workpiece immediately started to melt and the heat affected zone was formed. The moving boundary of the crater was also identified with time. When the radial and axial conductivities were increased separately, the temperature distribution and the shape of the crater were shifted in the radial and axial directions, respectively. The material removal rate was found to be higher when the conductivity was increased in the radial direction rather than in the axial direction.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.17 no.5
• /
• pp.508-514
• /
• 2004

A fluxgate magnetic sensor consists of a solenoid excitation coil, pick-up coil, and magnetic core. We presents the effect of magnetic core shape in a micromachined fluxgate sensor. To observe the performance of fluxgate sensor with magnetic core side width and gap, side width of 125 ${\mu}{\textrm}{m}$, 250 ${\mu}{\textrm}{m}$, and 500 ${\mu}{\textrm}{m}$ were designed in a rectangular-ring shaped core and the gaps of 0 ${\mu}{\textrm}{m}$, 50 ${\mu}{\textrm}{m}$, and 100 ${\mu}{\textrm}{m}$ were also fabricated in a racetrack shaped core. The solenoid coils and magnetic core were separated by benzocyclobutane(BCB) which had high insulation and good planarization characters. Copper coil patterns of 10 ${\mu}{\textrm}{m}$ width and 6${\mu}{\textrm}{m}$ thickness were electroplated on Ti(300 $\AA$) / Cu(1500 $\AA$) seed layers. 3 ${\mu}{\textrm}{m}$ thick N $i_{0.8}$F $e_{0.2.}$(permalloy) film for the magnetic core was also electroplated under 2000 gauss to induce the magnetic anisotropy. The magnetic core had the high DC effective permeability of ∼1,300 and coercive field of ∼0.1 Oe. Because the magnetic cores of 500 ${\mu}{\textrm}{m}$ side width and 0 gap had a low magnetic flux leakage, high sensitivity of ∼350 V/T were measured at excitation condition of 3 $V_{P-P}$ and 2 MHz square wave. The power consumption of ∼14 ㎽ was measured. The fabricated fluxgate sensor had the very small actual size of 3.0${\times}$1.7 $\textrm{mm}^2$. When two fluxgates were perpendicularly aligned in terrestrial field, their two-axis output signals were very useful to commercialize an electronic azimuth compass for the portable navigation system.m.m.m.

• Composites Research
• /
• v.17 no.5
• /
• pp.1-6
• /
• 2004

Composite pressure vessels with HDPE (high density polyethlyne) liner with metal boss at each end were developed by Filament Winding Process. The vessel is composed of a dome-shaped part at each end and a cylinder-shaped part at the middle of the vessel. The environmental tests carried out for possible vessel materials such as High Density Polyethlyn (HDPE), resins and reinforcing fibers up to a year showed no significant damages. The boss was designed to minimize the gas leak which was verified by FEM analysis. Most ideal fiber tension was obtained by experimental method and the fiber volume fraction, $\textrm{V}_{f}$, obtained by image analyzer were 55.4 % in cylinder and 55.6 % in dome parts, respectively. Winding pattern is programmed to control the composite thickness in the dome areas such that the failure of the vessel may occur in the cylinder. During the cure, the vessel was rotated and a constant internal pressure of 0.62 bar was applied. From this, the vessel's burst pressure is improved by 28 %. The burst and fatigue tests for under-wound and fully wound vessel showed satisfactory results.

• Korean Journal Plant Pathology
• /
• v.14 no.6
• /
• pp.646-650
• /
• 1998

Mycological characteristics of Phytophthora nicotianae var. nicotianae SPC10 (A1 type) causing Phytophthora rot of strawberry and the resistances of 11 strawberry cultivars against the pathogen were examined. Optimum temperature for the mycelial growth of the pathogen was obtained in the range of 30~35$^{\circ}C$, and the growth was completely stopped under 13$^{\circ}C$ or over 42$^{\circ}C$. Aerial mycelia were abundant on oatmeal agar (OMA), V-8 juice agar (V8A) and lima bean agar (LBA) medium, although there were slight differences, however, on cornmeal agar (CMA) medium, it was a shape of stellate without aerial mycelia. The colony shape on potato dextrose agar (PDA) medium was rough and irregular whereas the mycelial growth was slow, and some aerial mycelia were only produced in the middle of PDA medium. Optimum temperature for sporangial formation was 3$0^{\circ}C$, and zoospores were mostly released at $25^{\circ}C$ from the sporangia. Sporangia were more produced in C/Z solution with pH 5. 0~6.$0^{\circ}C$ than sterilized distilled water (DSW) and distilled water (DW), and zoospores were also released much more than other solutions. Eleven strawberry cultivars such as Reiko, Hokowase, Eyeberry, Akaneko, Sistakara, Toyonoka, Nyoho, Sulhong, Suhong, Myhong and Wonkyo #3104 revealed the disease incidence up to 88.9~100% by the leaf inoculation with mycelial disk. However, Nyoho and Suhong showed higher level of resistance against the pathogen by root inoculation.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.25 no.4
• /
• pp.29-37
• /
• 1983

This study was carried out not only to prepare available materials that can be utilized in basic planning of irrigation reservoirs, but also to contribute to the study on countermeasures for reasonable irrigation water development in Korea in the future, through the investigation for the structural characteristics of reservoirs and their change trend by an epoch. During this study 123 sites of sample reservoirs were analysed in their dimensions of physical constituent factors. The physical characteristics and their change trends revealed by this study are summarized as follows: 1. For the irrigation earth dam in Korea the correlation between dam volume (v) and dam height & length (H$^2$L) can be described as the formula of v=1. 434H2L~17, 300 (r=0. 933), from which embankment amount is assumed to be quickly estimated under determined dam height and length of the proposed reservoir. 2. The ratio of dam volume to dam height & length ranges approximately from 0.5 to 3 (1.7 in average), that of storage capacity to dam volume 2 to 10 (8.4 in average), that of irrigation area to full water surface area 5 to 20 (13 in average) and that of catchment area to irrigation area 2 to 5 (4 in average). Though correlation between dam volume and dam height & length is high, that between others is relatively low. 3. Average storage depth ranges approximately from 4m to l0m (6.6m in average), unit storage capacity 0. 4m to 0. 8m (0.54 in average) and shape factor of dam 5 to 20 (10.5 in average). 4. The more recently planned the reservoirs were, the less storage capacity, dam volume, full water surface and dam shape factor they have. 5. The more recently planned the reservoirs were, the larger storage depth and unit storage capacity they have.