• Journal of Electrochemical Science and Technology
• /
• 제4권3호
• /
• pp.93-101
• /
• 2013

The electrodeposition of indium onto a copper electrode from an aqueous sulfate solution containing $In^{3+}$ was studied by means of cyclic voltammetry and chronoamperometry. Reduction and oxidation of indium on copper were investigated by using cyclic voltammograms at different negative limiting potentials and at different scan rates in cumulative cycles. Cyclic voltammograms indicated that reduction and oxidation processes of indium could involve various reactions. Chronoamperometry was carried out to analyze the nucleation mechanism of indium in the early stage of indium electrodeposition. The non-dimensional plot of the current transients at different potentials showed that the shape of the plot depended on the applied potential. The nucleation of indium at potential step of -0.6~-0.8 V was close to progressive nucleation limited by diffusion. However the non-dimensional plot of current transients for the indium nucleation showed different behaviors from theoretical curves at the potential step lower than -0.8 V.

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제4권1호
• /
• pp.12-17
• /
• 2004

The body-tied FinFETs (bulk FinFETs) implemented on bulk Si substrate were characterized through 3-dimensional device simulation. By controlling the doping profile along the vertical fin body, the bulk FinFETs can be scaled down to sub-30 nm. Device characteristics with the body shape were also shown. At a contact resistivity of $1{\times}10^{-7}\;{\Omega}\;cm^2$, the device with side metal contact of fin source/drain showed higher drain current by about two. The C-V results were also shown for the first time.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• 제18권2호
• /
• pp.109-115
• /
• 2005

The study of Oxygen Vacancy on SnO$_2$ thin films grown by thermal chemical vapor deposition were investigated with different substrate temperature. X-ray diffraction showed that the crystallinity of the grown thin films increased with increasing substrate temperature. Two narrow peaks and two broad peaks were observed from the photoluminescence measurements at 6 K. The intensity and shape of the broad peaks were changed with increasing substrate temperature. It was concluded that the origin of the broad peak at 2.4 eV was due to oxygen vacancies and that of peak at 3.1 eV was related to structural defects. Hall effect measurements showed that the carrier density was decreased as increasing deposition time from 10 to 30 min., but increased for the deposition of 60 min.

• Journal of the Korean Statistical Society
• /
• 제4권1호
• /
• pp.19-33
• /
• 1975

The Ministry of Agriculture and Fishery had carried out a random sample survey on rice yield by the method of plot cutting since 1959 to obtain correct statistics on rice production. There are important problems connected with the determination of optimum size and shape of sample plot, variation of yield between plots and field and variation in the time needed for different types of plot cutting. This kind of research has been performed in India by Dr. P. V. Sukhatme and Dr. V. G. Panse. Also the same optimum procedures are much different in Japan that in India. In Korea, the optimum procedures may well be different from either of these countries. Although the government is proceeding with the crop yield survey, it does not attempt to investigate plot problems but emphasize total rice yield estimation. This particular research was conducted on a scale enough that the author could personally supervise all of the work.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 한국소음진동공학회 2014년도 추계학술대회 논문집
• /
• pp.773-778
• /
• 2014

Recently both high performance and low noise for a cooling fan used in a server computer have been required. In this study, we measured the noise characteristics for a small cooling fan used in a computer or in a server, and compared the computational data to measured ones. SC/Tetra V10 and FlowNoise V4.3 was used for the unsteady flow field and the aeroacoustic analysis, respectively. The aeroacoustic analysis results have the good agreement with measured data within 3% errors in overall SPL. In the noise spectrum, we could find the peak tonal noise at lower frequency than 1st BPF, and confirm that the reason is caused by the asymmetry of bell mouth shape.

• Journal of The Korean Astronomical Society
• /
• 제11권1호
• /
• pp.31-36
• /
• 1978

Although Serkowski used a single value K=1.15 in representing all the observed interstellar linear polarization curves by his empirical relation $p({\lambda})/P_{max}$=exp (-K $1n^2({\lambda}_{max}/{\lambda})$), where $p_{max}$ is the maximum polarization at wavelength ${\lambda}_{max}$, we have noticed a meaningful variation in K from observations of 72 stars. By comparing K's with $P_{max}/E_{B-V}\;and\;with\;{\lambda}_{max}$, we have examined how the shape of the polarization curve is related with the degree of grain alignment on one hand, and with grain sizes on the other. We have shown that correlations between K, $P_{max}/E_{B-V}\;and\;with\;{\lambda}_{max}$, are consistent with the idea of Davis-Greenstein mechanism for grain alignment.

• Journal of the Korean Ceramic Society
• /
• 제26권6호
• /
• pp.836-842
• /
• 1989

In this study, finely divided vanadium pentoxide was prepared by carrying vapor of vanadyl trichloride into the flame of an C3H8-O2-H2 with a specially designed burner. The flame-synthesized oxide particles had a nonporous spherical shape with nearly constant diameter in the range of 200-600$\AA$. The surface area of these particles depends on the residence time and the concentration of metal chloride vapor in the burner. The experimental results showed that the growth of particles is controlled by fusion rather than collision. The crystal size of finely divided V2O5 particle was increased after calcination at temperature above 50$0^{\circ}C$.

• Proceedings of the KIEE Conference
• /
• 대한전기학회 1999년도 하계학술대회 논문집 E
• /
• pp.2051-2053
• /
• 1999

In this work, PD patterns and electrical trees are observed by use of the XLPE cable insulation. and the tree initiation voltage related to the contamination are also measured in order to calculate the electric stress necessary for the design of cable insulation. Throughout these works, correlation between the PD pattern and the shape of electrical tree has been observed that there may exist three distinct pattern of PD dependence on the stage of tree propagation, Such correlation could bring a basic information in connection with the partial discharge of cable system. It was also found that the electrical stress necessary for the initiation of electrical tree was measured to the 290kV/mm for the 154kV XLPE cables manufactured in KOREA.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• 제5권3호
• /
• pp.29-35
• /
• 2006

Various types of elliptical motions are generated by PZT mechanism which is composed of two parallel piezoelectric actuators. Elliptical vibration cutting(EVC) is obtained by attaching single crystal diamond cutting tool to the mechanism, and V-grooving for Brass and Aluminum is carried out by applying the EVC. It is experimentally observed that the cutting force in the process of the EVC reduces compared to the ordinary non-vibration cutting, which is due to the decrease of undeformed chip thickness and frictional force between the tool and chip. Ultrasonic elliptical vibration cutting(UEVC) suppresses burr formation and decreases cutting force still more, so UEVC makes it possible to enhance the shape accuracy of machined surface.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 한국추진공학회 2004년도 제22회 춘계학술대회논문집
• /
• pp.532-543
• /
• 2004

The present work have been developed the interpretation processor including the behavior of material failure and the separation phenomena under transient dynamic loading (the operation of explosive bolt) using AUTODYN V4.3, SoildWork 2003 and TrueGrid V2.1 programs. It has been demonstrated that the interpretation in ridge-cut explosive bolt under dynamic loading condition should be necessary to the appropriate failure model and the basic stress of bolt failure is the principal stress. The use of this interpretation processor developing the present work could be extensively helped to design the shape and the amount of explosives in the explosive bolt having a complex geometry. It is also proved that the interpretation processor approach is an accurate and effective analysis technique to evaluate the separation mechanism in explosive bolts.