• Journal of Electrical Engineering and Technology
• /
• v.4 no.2
• /
• pp.219-228
• /
• 2009

The growing application and the numerous qualities of induction motors (1M) in industrial processes that require high security and reliability levels has led to the development of multiple methods for early fault detection. However, various faults can occur, such as stator short-circuits and rotor failures. Traditionally the diagnosis machine is done through a sinusoidal power supply, in the present paper we study experimentally the effects of the rotor failures, such as broken rotor bars in function of the ac supplying, the load and show the impact of the converter from diagnosis of the machine. The technique diagnosis used is based on the spectral analysis of stator currents or stator voltages respectively according to the types of induction motor ac supplying. So, four different ac supplying are considered: ${\odot}$ the IM is directly by the balanced three-phase network voltage source, ${\odot}$ the IM is fed by a sinusoidal current source given the controlled by hysteresis, ${\odot}$ the IM is fed (in open loop) by a scalar control imposing through ratio V/f=constant, ${\odot}$ the IM is controlled through a vector control using space vector pulse width modulation (SVPWM) technique inverter with an outer speed loop.

• Animal cells and systems
• /
• v.11 no.1
• /
• pp.39-50
• /
• 2007

Tau plays a role in numerous neuronal processes, such as vesicle transport, microtubule-plasma membrane interaction and intracellular localization of proteins. SUMO (Small Ubiquitin-like Modifier) modification (SUMOylation) appears to regulate diverse cellular processes including nuclear transport, signal transduction, apoptosis, autophagy, cell cycle control, ubiquitin-dependent degradation, as well as gene transcription. We noticed that putative SUMOylation site is localized at $^{340}K$ of $Tau(^{339}VKSE^{342})$ with the consensus sequence information (${\Phi}KxE$ ; where ${\Phi}$ represents L, I, V or F and x is any amino acid). In this report, we demonstrated that $^{340}K$ of Tau is the SUMOylation site and that a point mutant of Tau S214E (an analog of the phospho $^{214}S$ Tau) promotes its SUMOylation at $^{340}K$ and its nuclear or nuclear vicinity localization, by co-immunoprecipitation and confocal microscopy analysis. Further, we demonstrate that the Tau S214E (neither Tau S214A nor Tau K340R) mutant increases its protein stability. However, the SUMOylation at $^{340}K$ of Tau did not influence cell survival, as determined by FACS analysis. Therefore, our results suggested that the phosphorylation of Tau on $^{214}S$ residue promotes its SUMOylation on $^{340}K$ residue and nuclear vicinity localization, and increases its stability, without influencing cell survival.

• Journal of Ginseng Research
• /
• v.48 no.4
• /
• pp.417-424
• /
• 2024

Background: This research main objective was to evaluate a proliposomes (PLs) formulation for the enhancement of oral bioavailability of ginsenosides, using ginsenoside Rg3 (Rg3) as a marker. Methods: A novel PLs formulation was prepared using a modified evaporation-on-matrix method. Soy phosphatidylcholine, Rg3-enriched extract, poloxamer 188 (Lutrol® F 68) and sorbitol were mixed and dissolved using a aqueous ethanolic solution, followed by the removal of ethanol and lyophilization. The characterization of Rg3-PLs formulations was performed by powder X-ray diffractometry (PXRD), transmission electron microscopy (TEM) and in vitro release. The enhancement of oral bioavailability was investigated and analyzed by noncompartmental parameters after oral administration of the formulations. Results: PXRD of Rg3-PLs indicated that Rg3 was transformed from crystalline into its amorphous form during the preparation process. The Rg3-encapsulated liposomes with vesicular-shaped morphology were generated after the reconstitution by gentle hand-shaking in water; they had a mean diameter of approximately 350 nm, a negative zeta potential (- 28.6 mV) and a high entrapment efficiency (97.3%). The results of the in vitro release study exhibited that significantly more amount of Rg3 was released from the PLs formulation in comparison with that from the suspension of Rg3-enriched extract (control group). The pharmacokinetic parameters after oral administration of PLs formulation in rats showed an approximately 11.8-fold increase in the bioavailability of Rg3, compared to that of the control group. Conclusion: The developed PLs formulation could be a favorable delivery system to improve the oral bioavailability of ginsenosides, including Rg3.

• Applied Biological Chemistry
• /
• v.41 no.6
• /
• pp.437-441
• /
• 1998

The effects of sucrose fatty acid ester (SE, 1% w/w) and glycerin (GL, 1% v/w) additions, storage temperature$(0,\;20\;and\;70^{\circ}C)$, and time $(0{\sim}6\;day)$ on texture properties, hardness(H), cohesiveness(O), chewiness(C) and rheological property(R) of Baikseolgi were studied. The H of Baikseolgi increased sharply in the early stage of storage at 0 and $20^{\circ}C$, while increased gently at $70^{\circ}C$ with increasing storage time. After 6 days of storage, the H of Baikseolgi at $20^{\circ}C$ had a little lower than that at $0^{\circ}C$. However, the H of Baikseolgi at $70^{\circ}C$ was 10.7% of that at $0^{\circ}C$. The addition of GL had greater effect on the reduction of H than that of SE. The H of control, SE and GL additions were 336, 216 and $$174\;g_f, respectively, after 6 days at $70^{\circ}C$. The O of Baikseolgi at $70^{\circ}C$ were higher than those at $0^{\circ}C$. The O of GL added Baikseolgi had the highest value and the second and the third were SE added and control, respectively. The O of Baikseolgi decreased with increasing storage time. The C of Baikseolgi of increased with increasing storage time, which had similar curve patterns to the H of Baikseolgi. Instantaneous stress and equilibrium stress of Baikseolgi decreased with increasing storage temperature. The affection of viscous element increased and that of elastic element decreased with increasing storage temperature.

• Journal of Microbiology and Biotechnology
• /
• v.19 no.9
• /
• pp.1055-1064
• /
• 2009

Enteroviruses were identified and characterized from patients with aseptic meningitis and other enterovirus-related diseases in Chungnam, Korea from 2005 to 2006. Enteroviruses were isolated from 79 of 519 cases (15.2%) in 2005, and 37 of 386 cases (9.6%) in 2006. Based on partial VP1 sequencing, a total of 116 enterovirus isolates were resolved into 13 types. Prevalent among the Chungnam isolates were echovirus 18 and coxsackievirus B5 in 2005, and echoviruses 5 and 25 in 2006. This is the first time echoviruses 5 and 18 have been identified in Korea since enterovirus surveillance began there in 1993. The temporal distribution of enterovirus epidemics in Chungnam showed a remarkable seasonal pattern, with cases occurring during most of the three months of the summer from June to August. The highest rate of enterovirus-positive cases occurred in patients less than 1 year of age. The ratio of male to female enterovirus-positive patients was approximately 1.8:1. Comparison of the VP1 amino acid sequences of the 15 coxsackievirus B5 isolates with reference strains revealed that all Chungnam isolates are substituted at positions 23 (V231), 19 (S19G), 75 (Y75F), and 95 (N95S). Upon comparing the nine ECV5 isolates with foreign strains, it was found that only the Chungnam isolates, with the exception of Kor06-ECV5-239cn, have P at position 153 and F at position 146. The three ECV9 isolates from 2006 show alterations at amino acids 36, 148, and 154 outside of the BC-loop and at position 84 in the BC-loop, whereas the seven isolates from 2005 and the other ECV9 strains in the database only show the alteration at position 84 (D, I, N, S). The five ECV25 isolates have an S residue at position 134, whereas most of the foreign strains have an N residue.

• Journal of Bio-Environment Control
• /
• v.19 no.1
• /
• pp.36-48
• /
• 2010

This present study was conducted to investigate photosynthetic characteristics, chlorophyll fluorescence, chlorophyll contents of Betula platyphylla var. japonica, Prunus leveilleana, Magnolia sieboldii, growing under four different light intensity regimes (full sun, and 64~73%, 35~42%, 9~16% of full sun). As result, Betula platyphylla var. japonica showed outstanding photosynthetic capacity and apparent quantum yield in full sun and showed low shade tolerance. Prunus leveilleana showed good photosynthetic capacity and apparent quantum yield in 64~73% or 35~42% of full sun and showed common shade tolerance. However, Magnolia sieboldii showed good photosynthetic capacity and apparent quantum yield in 35~42% of full sun, while the lowest in full sun. Magnolia sieboldii showed the highest shade tolerance compared to the other species. As the shading level increased, the total chlorophyll contents of all species increased with significant difference.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.10 no.5
• /
• pp.23-35
• /
• 2011

The pedestrian green time is usually long at wide width intersections. This sometimes causes the increase of delay on the whole intersection because of long cycle length and thus small g/C ratio on some direction. In this paper, to improve these problems, staggered pedestrian crossing was evaluated on the vehicular and pedestrian aspects. The results were gained by using both TRANSYT-7F and VISSIM model. The vehicle control delay of the staggered pedestrian crossing was estimated to be decreasing than that of the general pedestrian crossing by 14.9% to 85.6%. The pedestrian average delay of two pedestrian crossing systems was examined by analytical method and VISSIM. According to the analytical method there was no significant difference between each pedestrian crossing system. The pedestrian delay of staggered pedestrian crossing was from 13.4% to 22.3% than the general pedestrian crossing by VISSIM. In conclusion, the staggered pedestrian crossing was more effective than general pedestrian crossing for both the vehicle and the pedestrian. However this conclusion was resulted from micro simulation where traffic volume condition, v/c, was from 0.8 to 1.1.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.48 no.1
• /
• pp.96-103
• /
• 2015

The effects of $CO_2$ concentration, nutrient levels, and irradiance on the growth of germlings and juveniles, and on the photosynthesis of adults were examined in a green tide alga, Ulva australis. We used a factorial experimental design with two $CO_2$ concentrations (380 and 750 ppm), two nutrient levels (control and PES medium), and two irradiance levels (50 and $100{\mu}mol$ photons $m^{-2}s^{-1}$). Germlings grew best ($664.15{\pm}61.45{\mu}m$ in length) under conditions of 750 ppm, PES, and $100{\mu}mol$ photons $m^{-2}s^{-1}$ after 10 days in culture. Relative growth rates (RGR) of the juveniles were greatest (4.41% $day^{-1}$) under conditions of 750 ppm, PES, and $50{\mu}mol$ photons $m^{-2}s^{-1}$ after 5 days in culture. Photosynthetic efficiency ($F_v/F_m$) of the adult discs was $0.73{\pm}0.05$ before the experiment and reached a maximum ($0.83{\pm}0.01$) under conditions of 750 ppm, control, and $50{\mu}mol$ photons $m^{-2}s^{-1}$ after 5 days in culture. Growth (germlings and juveniles) and photosynthesis (adult discs) of Ulva australis increased when $CO_2$ levels were 750 ppm. Additionally, the optimal irradiance for growth and photosynthesis differed among stages, wherein germlings grew best at $100{\mu}mol$ photons $m^{-2}s^{-1}$, juveniles grew best at $50{\mu}mol$ photons $m^{-2}s^{-1}$, and adults photosynthesized most at $50{\mu}mol$ photons $m^{-2}s^{-1}$. The performance of Ulva australis at all examined life stages was enhanced under the PES nutrient treatment. In conclusion, the physiological responses of U. australis to varying $CO_2$, nutrient, and irradiance levels differed slightly among life stages. However, growth and photosynthesis always increased with elevated $CO_2$ and nutrient concentrations. These results indicate that U. australis green tide blooms might occur more frequently in coastal areas if $CO_2$ and nutrient concentrations increase.

• Progress in Medical Physics
• /
• v.27 no.3
• /
• pp.156-161
• /
• 2016

When air discharged from a radioisotope production facility is contaminated with radiation, the public may be exposed to radiation. The objective of this study is to manage such radiation exposure. We measured the airborne radioactivity concentration at a 30 MeV cyclotron radioisotope production facility to assess whether the exhaust gas was contaminated. Additionally, we investigted the radioactive contamination of the air filter for efficient air purification and radiation safety control. To measure the airborne radiation concentration, specimens were collected weekly for 4 h after the beginning of the radioisotope production. Regarding the air purifier, five specimens were collected at different positions of each filter-pre-filter, high-efficiency particulate air filter, and charcoal filter-installed in the cyclotron production room. The concentrations of F-18, I-123, I-131, and Tl-201 generated in the radioiodine production room were $13.5Bq/m^3$, $27.0Bq/m^3$, $0.10Bq/m^3$, and $11.5Bq/m^3$, respectively; the concentrations of F-18, I-123, and I-131 produced in the radioisotope production room were $0.05Bq/m^3$, $16.1Bq/m^3$, and $0.45Bq/m^3$, correspondingly; and those of F-18, I-123, I-131, and Tl-201 generated in the accelerator room were $2.07Bq/m^3$, $53.0Bq/m^3$, $0.37Bq/m^3$, and $0.15Bq/m^3$, respectively. The maximum radiation concentration of I-123 generated in the radioiodine production room was 1,820 Bq/g, which can be disposed after 2 days. The maximum radiation concentration of Tl-202 generated in the radioisotope production room was 205 Bq/g, and this isotope must be stored for 53 days. The I-123 generated in the radioiodine production room had a maximum concentration of 1,530 Bq/g and must be stored for 2 days. The maximum radiation concentration of Na-22 generated in the radioisotope production room was 0.18 Bq/g and this isotope must be disposed after 827 days. To manage the exhaust, the efficiency of air purification must be enhanced by selecting an air purifier with a long life and determining the appropriate replacement time by examining the differential pressure through systematic measurements of the airborne radiation contamination level.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.33 no.4
• /
• pp.653-660
• /
• 2006

Fuji VII is a glass-ionomer cement specially targeted for early protection in erupting first and second molars. Properties of Fuji VII such as very high level of fluoride release, low viscosity and no need to preliminarily etch the substrate would be useful to erupting molars with primary pit and fissure caries or hypoplastic area for preventive goal or remineralization. The purpose of this study were to evaluate remineralization of Fuji VII glass ionomer cement and to compare with one of other restorative materials such as conventional glass ionomer cement, resin-modified glass ionomer cement, compomer and composite resin. Forty-two extracted human molars were used for this study. All teeth were immersed in demineralizing solution for 48 hours after Class V cavity preparation was made on sound proximal surface. The teeth were randomly divided into six groups and restored with Fuji VII, Fuji II, Fuji II LC improved, F2000, $Filtek^{TM}$ Z250 and control group was unrestored. The middle area with $130{\pm}20{\mu}m$ thickness was separated from specimen using microtome and demineralized area was photographed under polarized microscope. Separated area was relocated to specimen and stored in artificial saliva, After four weeks, changes of demineralized area were observed and compared to them restorated immediately. The results from the this study can be summarized as follows ; 1. Fuji VII, Fuji II, Fuji II LC improved have more prominent remineralization effect than F2000, $Filtek^{TM}$ Z250, control group. 2. No significant differences in remineralization effect are seen between Fuji VII and Fuji II, Fuji II LC improved.