• Structural Engineering and Mechanics
• /
• 제91권2호
• /
• pp.197-209
• /
• 2024

The vibration of elastically supported bidirectional functionally graded (BDFG) sandwich beams on an elastic foundation is investigated. The sandwich structure is composed of upper and lower layers of BDFG material and the core layer of isotropic material. Material properties of upper and lower layers are assumed to vary continuously along the length and thickness of the beam with a power-law function. Hamilton's principle is used to deduce the vibration equations of motion of the sandwich Timoshenko beam. Then, the partial differential equation of motion is spatially discretized into a time-varying ordinary differential equation in terms of Chebyshev differential matrices. The eigenvalue equation associated with the free vibration is formulated to study the influence of various slenderness ratios, material gradient indexes, thickness ratios, foundation and support spring constants on the vibration frequency of BDFG sandwich beams. The present method can provide researchers with deep insight into the impact of various geometric, material, foundation and support parameters on the vibration behavior of BDFG sandwich beam structures.

• 태양에너지
• /
• 제7권2호
• /
• pp.22-29
• /
• 1987

This paper dealed with thickness variation of bottom heat sotrage zone due to salinity and flow rate of extration hot brine in small test solar pond (0.5m wide, 0.5m high, 1.0m long). Testing apparatus and situation were follows: 7.1 cm of height of suction diffuser and 1.8cm of height of discharge diffuser above the test pond respectively, 0.3cm of slot size of suction diffuser, 1.0cm of slot size of discharge diffuser, 47cm of length of the slot; heating of hot water ($75^{\circ}C$) through separated hot water tank, discharge of the brine into storage zone through discharge diffuser, the extration of the brine through suction diffuser, circulation of the extracted brine through a heat exchanger (cooler). Following results were obtained through the experiments. 1. In small test solar pond, the typical three zone which showed up in real solar pond were established. 2. Richardson Number was used more effectively to confirm hydrodynamic stability of the stratified flow. 3. The thickness of non convective layer had a great effect on the heat storage of the bottom convective layer, then the temperature of bottom convective layer had a relation to that of upper convective layer. 4. Optimum operating condition in the test pond was on 10%-15% of salt concentration and $0.05m^3/hr$ of flow rate of extraction hot brine. 5. Following thickness of 3 zones were available to obtain under optimum operation condition: o bottom storage zone: $30%{\pm}10%$ of total pond depth o non-convective zone: $40%{\pm}10%$ of total pond depth o Upper surface zone: $20%{\pm}10%$ of total pond depth.

• 수산해양교육연구
• /
• 제9권1호
• /
• pp.40-48
• /
• 1997

In this study, uniform pressure distribution with small hole on the surface of symmetric object were given to reduce the viscous frictional force. The results were as follows : 1. The velocity on upper stream were accelerated by uniform pressure distribution on symmetric objects for reducing the viscous frictional resistances. 2. The effects of the distributed small holes were reduced the viscous frictional resistances in down stream region more than upper stream due to the increasing pressure in reverse flow region. 3. The viscous skin friction on surface of symmetric objects with and without distributed small holes are effect in region of upper stream and much decreased in down stream region due to increasing of boundary layer thickness.

• 물과 미래
• /
• 제25권2호
• /
• pp.99-110
• /
• 1992

담수화호에서는 온도 및 염도차에 의하여 성층류가 발생하며 수심이 깊은 담수화호의 경우 그 형상이 더욱 뚜렷하다. 본 연구는 깊은 담수화호를 대상으로 내부환경면이 잘 발달된 이층류에 있어서 저층배수관의 유출수 염분농도를 실험을 통하여 규명하였다. 실험에 이용된 저층배수관은 세가지 유형으로 유입층과 배수관의 유출수 염분농도차를 무차원으로 수식화 하였고 유입층의 상층부 흐름이 순간적으로 배수되는 밀도층의 한계조건을 밀도 Froude수와 배수관의 직경 및 수심의 함수로 방정식을 유도하였다.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2007년도 춘계학술대회 논문집
• /
• pp.226-228
• /
• 2007

During asymmetrical cold rolling in AA 5052 sheet a reduction per a rolling pass was varied to investigate the effect of the ratio of the contact length between the roll and sample ($l_c$) to the sheet thickness (d) on the formation of shear textures. In order to intensify the shear deformation during asymmetrical rolling, AA 5052 sheet was asymmetrically cold rolled without lubrication by using different roll velocities of upper and lower rolls. Asymmetrical rolling with $l_c$/d=1.8 led to the formation of texture gradients throughout the sheet thickness in which the outer thickness layers depicted shear textures and the center thickness layers displayed a rolling texture. Asymmetrical rolling with $l_c$/d=3.1 gave rise to the formation of shear textures in the whole through-thickness layer. The strain states associated with asymmetrical rolling were investigated by the finite element method (FEM) simulation. FEM results indicated that the evolution of deformation texture in a thickness layer is strongly governed by integrated values of strain rates and along the streamline in the roll gap.

• 대한토목학회논문집
• /
• 제13권2호
• /
• pp.237-242
• /
• 1993

기초 지반이 몇개의 토층으로 구성된 경우 그 지지력은 각 토층의 강성도와 두께 및 위치 등에 의해 영향을 받는다. 따라서 기초 설계시에 기초의 지지력을 정확히 구하고 파괴면을 예측하기 위해서는 토층의 상태를 지지력 계산에 고려해야 한다. 본 연구에서는 기초 지반이 사질지반이고 중간에 상대적으로 조밀한 지층을 포함하는 경우에 조밀한 층의 두께나 위치가 기초의 지지력 및 파괴모양에 미치는 영향을 극한 해석의 상한한계(upper bound)쪽에서 완전해에 가까운 해를 구하는 K.E.M(Kinematical Element Method)을 이용하여 검토 하였으며, 기초 폭(B)의 3/5 B보다 깊지 않은곳에 조밀한 층이 위치하는 경우에는 기초의 지지력 과 파괴모양이 조밀한 층의 영향을 받는 것으로 나타났다.

• 한국광학회지
• /
• 제22권1호
• /
• pp.53-57
• /
• 2011

본 논문에서는 통상적인 LED 구조 위에 추가적으로 상부 층을 형성하여 LED의 광 추출 효율을 개선하였다. 상부 층의 두께 및 굴절률 변화에 따른 LED의 광 방출 특성을 전산모사하였고 광 추출 효율이 개선되는 조건을 분석하였다. 약 1.05~1.40의 굴절률 범위에서 LED의 광방출이 증가하였다. 또한, 이 범위에서 두께가 증가할수록 광방출이 증가하였다. 굴절률이 1.30@589.3 nm인 인덱스 매칭 액체를 실제 LED의 상부 층으로 형성하여 LED의 광 추출 효율이 약 22% 정도 향상됨을 실험적으로 보였다. 이렇게 LED 위에 상부 층을 형성하는 개념은 간단하게 LED의 광 추출 효율을 개선할 수 있을 것으로 기대된다.

• 한국환경과학회지
• /
• 제13권8호
• /
• pp.721-731
• /
• 2004

The dispersion of suspended particulates in the coastal complex terrain of mountain-inland basin (city)-sea, considering their recycling was investigated using three-dimensional non-hydrostatic numerical model and lagrangian particle model (or random walk model). Convective boundary layer under synoptic scale westerly wind is developed with a thickness of about I km over the ground in the west of the mountain, while a thickness of thermal internal boundary layer (TIBL) is only confined to less than 200m along the eastern slope of the mountain, below an easterly sea breeze circulation. At the mid of the eastern slop of the mountain, westerly wind confronts easterly sea breeze, which goes to the height of 1700 m above sea level and is finally eastward return flow toward the sea. At this time, particulates floated from the ground surface of the city to the top of TIBL go along the eastern slope of the mountain in the passage of sea breeze, being away the TIBL and reach near the top of the mountain. Then those particulates disperse eastward below the height of sea-breeze circulation and widely spread out over the coastal sea. Total suspended particulate concentration near the ground surface of the city is very low. On the other hand, nighttime radiative cooling produces a shallow nocturnal surface inversion layer (NSIL) of 200 m thickness over the inland surface, but relatively thin thickness less than 100m is found near the mountain surface. As synoptic scale westerly wind should be intensified under the association of mountain wind along the eastern slope of mountain to inland plain and further combine with land-breeze from inland plain toward sea, resulting in strong wind as internal gravity waves with a hydraulic jump motion bounding up to about 1km upper level in the atmosphere in the west of the city and becoming a eastward return flow. Simultaneously, wind near the eastern coastal side of the city was moderate. Since the downward strong wind penetrated into the city, the particulate matters floated near the top of the mountain in the day also moved down along the eastern slope of the mountain, reaching the. downtown and merging in the ground surface inside the NSIL with a maximum ground level concentration of total suspended particulates (TSP) at 0300 LST. Some of them were bounded up from the ground surface to the 1km upper level and the others were forward to the coastal sea surface, showing their dispersions from the coastal NSIL toward the propagation area of internal gravity waves. On the next day at 0600 LST and 0900 LST, the dispersed particulates into the coastal sea could return to the coastal inland area under the influence of sea breeze and the recycled particulates combine with emitted ones from the ground surface, resulting in relatively high TSP concentration. Later, they float again up to the thermal internal boundary layer, following sea breeze circulation.

• 한국산학기술학회논문지
• /
• 제8권5호
• /
• pp.1179-1185
• /
• 2007

본 논문은 슬래브내의 보 상부철근의 영향을 파악하기 위한 해석적 연구로 슬래브가 있는 보-기둥 접합부에서 기존의 설계방법인 직사각형 단면 내에 상부철근을 2단으로 배근한 보와 동일량의 상부철근을 직사각형 단면에 1단만 배근하고 나머지는 보의 적정 플랜지폭 내에 분산 배치하여 상부철근의 배치에 따라 보의 휨 강도가 어떻게 변화하는지를 정량적으로 평가할 수 있도록 하는 것이다. 이러한 연구 목적을 수행하기 위하여 상용화된 범용 구조해석 프로그램인 ANSYS를 이용하여 모델링하고, 비선형 구조해석을 실시하였다. 플랜지폭, 플랜지(슬래브)두께 및 상부 플랜지내에서의 철근의 위치 등을 변수로 한 수치해석을 통하여 보의 최대내력을 비교 검토한 결과, 플랜지폭의 영향은 상부 인장철근을 1단으로 직사각형 단면에서 멀리 배치할수록 내력차이가 증가하는 것을 확인하였으며, 플랜지폭이 동일한 계열에서 내력이 증가되는 비율은 플랜지두께의 영향을 크게 받지 않는 것으로 나타났고, 상부 인장철근의 위치에 따른 내력은 슬래브두께가 증가할수록 내력의 차이가 줄어드는 것으로 나타났다.

• 치과방사선
• /
• 제29권1호
• /
• pp.87-103
• /
• 1999

Purpose: This study was undertaken to quantitatively estimate the degree of the damage and recovery of the irradiated rat condylar cartilage using the Image Analyzer. Materials and Methods: Experimental animals were 16 male rats of the Sprague-Dawley strain at the age of 20 day irradiated with the dose of 10 Gy in their head and neck region. Four rats were sacrificed at the each of the following time intervals - 1, 4, 7 and 14 days, respectively. The same number of control group animals were sacrificed at the each age of 21. 24, 27 and 34 days, respectively. The specimens were stained with 0.5％ toluidine blue and examined with light microscope. The condylar cartilage was divided into 4 zones; fibrous zone, proliferating zone, upper hypertrophic zone, and lower hypertrophic zone. And then, the proliferating zone was subdivided into 2 layers - upper and lower layer, and upper and lower hypertrophic zone were subdivided into three layers, respectively - upper, middle and lower layer. With the aid of Image Analyzer, morphometric analysis was performed. The thickness, the numerical density of cells, the cell area density, the extracellular matrix area density, the mean area of single cell, the mean area of extracellular matrix per single cell were measured and analysed. Results: In the experimental group, the thickness of the fibrous zone was slightly increased and that of the proliferating zone and the upper and the lower hypertrophic zone was markedly decreased. With time, the thickness of the fibrous zone was gradually increased and that of the proliferating zone and the upper and the lower hypertrophic zone was steadily in the decreased state. The numerical density of cells of the proliferating zone was increased on post-irradiated 1 day, but decreased after post-irradiated 4 day, and that of the upper hypertrophic zone was decreased. The numerical density of cells of the lower hypertrophic zone was decreased in the early stage and then was decreased or not significantly different from that of the control group with time. In the experimental group, the cell area density of the fibrous zone and the proliferating zone was decreased in the early stage and then gradually increased or not significantly different from that of the control group with time. The cell area density of the upper and the lower hypertrophic zone was varied with time. The extracellular matrix area density value were totally opposite to the cell area density values: The mean area of single cell of the fibrous zone and the proliferating zone was .decreased on post-irradiated 1 day, and increased after post-irradiated 4 day. The mean area of single cell of the upper hypertrophic zone was varied with each layer and time. In the experimental group, the mean area of extracellular matrix per single cell of the fibrous zone was not significantly different with control group, and that of the proliferating zone was decreased on post-irradiated 1 day, and increased after post-irradiated 4 day. The mean area of extracellular matrix per single cell of the lower hypertrophic zone was increased in the early stage. and that of upper hypertrophic zone was varied with each layer and time. Conclusion: The condylar cartilages of rats were affected by irradiation, but the changes were vaned with each layer and time. By morphometric analysis. the changes of the cells of the condylar cartilage of irradiated rat could be calculated quantitatively.