• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2013년도 춘계 학술논문 발표대회
• /
• pp.35-36
• /
• 2013

Electric arc furnace oxidizing slag from massively produced steel slag has been used in road bases and subbases, hot mix asphalt, and landfill. Electric arc furnace oxidizing slag contains iron (15%~30%) and has a high density of 3.0~3.7 ton/m3. Depending on the type and amount of concrete aggregates, the radiation-shielding characteristics can vary. Therefore, aggregates of electric arc furnace oxidizing slag can be considered for the production of radiation-shielding concrete. The experimental design of this study is experiments on Compressive strength experiments, X-ray irradiation experiments, and experiments related to the unit volume weight were carried out on hardened concrete. This experiment compared the performance evaluation of radiation shielding of concrete using electric arc furnace oxidizing slag.

• 한국구조물진단유지관리공학회 논문집
• /
• 제16권4호
• /
• pp.107-115
• /
• 2012

본 연구에서는 경량 콘크리트에 대한 361개, 보통중량 콘크리트에 대한 1,335개 및 고중량 콘크리트에 대한 221개의 데이터를 이용하여 콘크리트의 인장강도 (직접인장강도, 쪼갬인장강도 및 파괴계수)에 대한 설계기준과 기존 연구자들의 제안모델의 안정성을 평가하였다. 콘크리트 인장강도 예측을 위한 대부분의 제안 식들은 보통중량 콘크리트의 실험결과를 이용하여 압축강도의 함수로서 제시되었다. 하지만 데이터베이스의 분석은 콘크리트 인장강도는 기건 단위질량에 의해서도 중요한 영향을 받음을 보여준다. 이에 따라, 콘크리트 인장강도에 대한 기준 및 제안모델들은 기건 단위질량 2,100 $kg/m^3$ 이하, 압축강도 50 MPa 이상에서는 실험결과와의 불일치가 증가하였다. 한편, 본 연구에서 콘크리트 기건 단위질량을 고려하여 제시된 콘크리트 인장강도 예측 모델들은 실험결과와 비교적 잘 일치하였다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2010년도 추계 학술발표회
• /
• pp.736-742
• /
• 2010

This study was conducted to characterize on the relationships of rainfall intensity and infiltration rate of rainfall dependent on unit weight change in the gneissic weathered soil by a column test equipment. In this study, volumetric water content and pore water pressure were measured using TDR sensors and tensiometers at regular time intervals. Rainfall conditions including continuous rainfall and repeated rainfall were selected in order to know the effect of antecedent rainfall. In the condition of rainfall intensity 20mm/h and the unit weights of soil as $1.35g/cm^3$, $1.55g/cm^3$ and $1.61g/cm^3$, average rainfall infiltration rate was $2.814{\times}10^{-3}cm/sec$, $1.969{\times}10^{-3}cm/sec$ and $1.252{\times}10^{-3}cm/sec$ respectively. The higher rainfall intensity and lower unit weight of soil, the faster average infiltration rate. Overflow in the column was happened except rainfall condition of rainfall intensity 20mm and soil unit weight $1.35g/cm^3$. Increasing the soil unit weight, overflowed water was increased and occurrence time was faster.

• Computers and Concrete
• /
• 제33권4호
• /
• pp.471-479
• /
• 2024

In urban areas, appropriate backfilling design is necessary to prevent surface subsidence and subsurface cavities after excavation. Expandable foam grout (EFG), a mixture of cement, water, and an admixture, can be used for cavity filling because of its high flowability and volume expansion. EFG volume expansion induces a porous structure that can be quantified by the entrapped air content. This study observed the unit weight variations in the EFG before and after expansion depending on the various admixture-cement and water-cement ratios. Subsequently, the air content before and after expansion and the gravimetric expansion ratios were estimated from the measured unit weights. The air content before expansion linearly increased with an increase in the admixture-cement ratio, resulting in a decrease in the unit weight. The air content after the expansion and the expansion ratio increased nonlinearly, and the curves stabilized at a relatively high admixture-cement ratio. In particular, a reduced water-cement ratio limits the air content generation and expansion ratio, primarily because of the short setting time, even at a high admixture-cement ratio. Based on the results, the relationship between the maximum expansion ratio of EFG and the mixture ingredients (water-cement and admixture-cement ratios) was introduced.

• 한국연초학회지
• /
• 제4권2호
• /
• pp.41-50
• /
• 1982

To investigate tile effects of growth characteristics on the yield, price per Kg, chemical contents and physical properties in Burley tobacco, ten varieties including Burley 21 were tested in this study. The results obtained are summarized as follows. 1 Forty to fifty days after transplanting, CCR (Crop Growth Rate) was the highest. RCR (Relative Growth Rate) increased up to 40 days, but decreased 50 days when maturation began. High- yielding varieties showed high CCR and RCR till 60 days. 2. Total alkaloid content of cured leaf increased about three times than that of topping stage, but the increased rates were some what different among varieties. 3. Leaf area, stalk diameter, stalk height and days to flower showed positive correlations to yield, whereas leaf thickness and weight per unit leaf area showed negative. 4 Varieties which are high in cured leaf weight ratio and weight per unit leaf thickeners showed relatively poor quality. 5 Nitrogen content was high in leafy and larger stalk diameter variety. 6. There are positive correlation between weight per unit leaf thickness and filling power. The time of combustion was positively correlated to leaf thickness and weight Per unit leaf. 7. It can be concluded that many characteristics are related to the yield, but not quality. It is, there fore, easy to Predict tile yield, but difficult to forecast the qualiffy.

• 한국농공학회지
• /
• 제39권4호
• /
• pp.75-81
• /
• 1997

This study was performed to evaluate the engineering properties of surlightweight polymer concrete using synthetic lightweight aggregate. The following conclusions were drawn; 1. The unit weight was in the range of 0.849~0.969t/$m^3$, the unit weights of those concrete were decreased by 58 ~ 63% than that of the normal cement concrete. 2. The highest strength was achieved by $P_1$, and compressive strength was increased by 93% and bending strength by 364% than that of the normal cement concrete, respectively. 3. The ultrasonic pulse velocity was in the range of 2, 346~2, 702m/s, which was low compared to that of the normal cement concrete. 4. The dynamic modulus of elasticity was in the range of $1.561{\times} 10{^5}~1.916{\times} 10{^5}kgf/cm^2$, which was approximately 52~98% of that of the normal cement concrete. 5. The compressive and bending strength were increased with the increase of unit weight. But, the dynamic modulus of elasticity and ultrasonic pulse velocity were decreased with the increase of unit weight.

• Structural Engineering and Mechanics
• /
• 제88권2호
• /
• pp.169-178
• /
• 2023

Lightweight aggregate concrete (LWAC) has various advantages, but it has limitations in ensuring sufficient ductility as structural members such as reinforced concrete (RC) columns due to its low confinement effect of core concrete. In particular, the confinement effect significantly decreases as the axial load increases, but studies on evaluating the ductility of RC columns at high axial loads are very limited. Therefore, this study examined the effects of concrete unit weight on the seismic performance of RC columns subjected to constant axial loads applied with different values for each specimen. The column specimens were classified into all-lightweight aggregate concrete (ALWAC), sand-lightweight aggregate concrete (SLWAC), and normal-weight concrete (NWC). The amount of transverse reinforcement was specified for all the columns to satisfy twice the minimum amount specified in the ACI 318-19 provision. Test results showed that the normalized moment capacity of the columns decreased slightly with the concrete unit weight, whereas the moment capacity of LWAC columns could be conservatively estimated based on the procedure stipulated in ACI 318-19 using an equivalent rectangular stress block. Additionally, by applying the section lamina method, the axial load level corresponding to the balanced failure decreased with the concrete unit weight. The ductility of the columns also decreased with the concrete unit weight, indicating a higher level of decline under a higher axial load level. Thus, the LWAC columns required more transverse reinforcement than their counterpart NWC columns to achieve the same ductility level. Ultimately, in order to achieve high ductility in LWAC columns subjected to an axial load of 0.5, it is recommended to design the transverse reinforcement with twice the minimum amount specified in the ACI 318-19 provision.

• 한국초등과학교육학회지:초등과학교육
• /
• 제21권2호
• /
• pp.201-212
• /
• 2002

This paper aims to find out how did elementary students understand scientific units in science textbooks. The subjects were 191 students of the 6th grade from 7 elementary schools in 3 different areas, consisting of 70 from 4 village schools of, 64 from 2 town schools of Gyeongnam province, and 57 from one city school in Ulsan Metro City. A test was developed based on the analysis of scientific units in the science textbooks and teacher's manuals constructed according to the 6th and 7th National Science Curriculum. The understanding of elementary students' on the scientific units(Temperature, Length, Weight, Volume, Speed, Plane Angle) were surveyed. The result are as follows: Regarding the temperature unit, the students generally well understand why to measure and how to read temperature, but had some problem in recording it, in confusion with the plane angle sign. As for the length unit, they obtained high scores in understanding the purpose of measuring length as well as recording and reading it. Which indicates that they are well aware of and use the unit appropriately. With respect to the weight unit, they got high scores in reading and recording weight, which means most students have no problem using the unit. However, it was found that they do not understand why to use the plate balance scale. The volume unit was one in which the students got relatively lower scores. They do not perceive the object of using a scale cylinder and confuse it with a device of length measurement. The unit of speed is the most difficult one for children's of science to understand, presumably, because it is an derived unit from two basic units. It is also assumed that the students got the highest score in the plane angle unit because they studied the unit immediately before the test. From the children's understanding of science units above the teacher's understanding and teaching methods presumed to play a major role for children to understand and use the science units properly.

• 대한안전경영과학회:학술대회논문집
• /
• 대한안전경영과학회 2009년도 추계학술대회
• /
• pp.565-572
• /
• 2009

This paper presents the optimization steps with weight and importance of estimated characteristic values in the multiresponse surface analysis(MRA). The research introduces the shape parameter of individual desirability function for relaxation and tighening of specification bounds. The study also proposes the combinded desirability function using arithmetic, geometric and harmonic means considering the measurement unit and numerical pattern.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2008년도 춘계 학술발표회 제20권1호
• /
• pp.793-796
• /
• 2008

최근 콘크리트 구조물 공사에서는 공기단축을 통한 경제성 확보와 동절기 초기동해방지를 위하여 콘크리트의 조기강도 발현을 요구되고 있다. 이에 본 연구에서는 조강형 AE감수제의 종류별 단위시멘트량과 양생온도 조건에 따른 압축강도발현 특성, 공기량 및 슬럼프 등의 경시변화를 검토하여 재령 24시간에 거푸집 조기 제거가 가능한 압축강도 5MPa을 발현시킬 수 있는 최적 조건을 제시하고자 하였다. 실험결과, 온도 $15^{\circ}C$에서 거푸집조기 제거가 가능한 압축강도 5MPa 발현 시간은 조강형 나프탈렌계 감수제를 사용한 경우 단위시멘트량 $330kg/m^3$에서 표준형 감수제에 비하여 10시간 빠른 22시간, $360kg/m^3$에서는 7시간 빠른 20시간, $390kg/m^3$에서는 4시간 빠른 18시간으로 나타났다. 또한 온도 $5^{\circ}C$에서는 조강형 나프탈렌계 감수제를 사용한 경우 단위시멘트량 $330kg/m^3$에서 표준형 감수제에 비하여 10시간 빠른 32시간, $360kg/m^3$에서는 7시간 빠른 30시간, $390kg/m^3$에서는 4시간 빠른 27시간으로 나타났다. 따라서 양생온도가 $10^{\circ}C$ 높아짐에 따라 압축강도 5MPa 도달시간은 10시간이 단축되었다.