• Journal of Positioning, Navigation, and Timing
• /
• v.5 no.4
• /
• pp.221-233
• /
• 2016

This paper deals with performance assessment of the kinematic network-based GPS positioning technique with a view to using it for ellipsoidally referenced bathymetric surveys. To this end, two field trials were carried out on a land vehicle and a surveying vessel. Single-frequency GPS data acquired from these tests were processed by an in-house software which equips the network modeling algorithm with instantaneous ambiguity resolution procedure. The results reveals that ambiguity success rate based on the network model is mostly higher than 99.0%, which is superior to that of the single-baseline model. In addition, achievable accuracy of the technique was accessed at ${\pm}1.6cm$ and 2.7 cm with 95% confidence level in horizontal and vertical component respectively. From bathymetric survey at the West Nakdong River in Busan, Korea, 3-D coordinates of 2,011 points on its bed were computed by using GPS-derived coordinates, attitude, measured depth and geoid undulation. Note that their vertical coordinates are aligned to the geoid, the so-called orthometric height which is widely adopted in river engineering. Bathymetry was constructed by interpolating the coordinate set, and some discussion on its benefit was given at the end.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.9 no.2
• /
• pp.207-211
• /
• 1999

$Si/Si_{1-x}Ge_x$ MODFET structures, incorporating linearly-graded buffer layers have been grown by GaS Source Molecular Beam Epitaxy. The growth temperature of the graded layers has not significantly changed the distribution of misfit dislocation. However, the surface undulation and surface defects were increased with increasing growth temperature. In $Si/Si_{1-x}Ge_x$ MODFET structures, the densities of misfit dislocations near the Si-active layers were considerably reduced in comparison with the region of graded layers. The electron mobility of $Si/Si_{1-x}Ge_x$ MODFET structure has increased with lowering the growth temperature.

• Journal of Ecology and Environment
• /
• v.33 no.3
• /
• pp.217-222
• /
• 2010

To determine whether or not the female Korean salamander, Hynobius leechii, responds to water currents and, if so, whether those responses depend on their reproductive conditions, we evaluated the responses of ovulated and oviposited females to 1-Hz water currents generated by a model salamander with and without the placement of a transparent water current blocker between the model and the test females. The ovulated females responded to water currents by turning their heads toward, approaching, and/or making physical contact with the model. When the water current blocker was in place, the number of salamanders that approached the model was reduced significantly. The approaching and touching responses of ovulated females were greater than those of oviposited females, whereas the other measurements evidenced no differences. None of the responses of the oviposited females to water currents was affected by the presence of the blocker. Our results indicate that female H. leechii responds to water currents via a mechanosensory system.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.11 no.2
• /
• pp.27-34
• /
• 1993

The construction of the accurate, economic topographic information for a sorts of work and a base facilities of country is one of the very important subjects. In this paper, Global network which include south KOREA and Regional network which include Chung-Nam/Chung-Buk provinces were designed, obtained WGS84 coordinates of control points in networks by GPS. The coefficients of transformation between WGS84 coordinates and Bessel coordinates in consideration of geoid undulations was derived by 7-parameter method. Also, the efficiency of 7-parameter method was proved through successful application of T.M. and U.T.M projection for the precise mapping, and the effectiveness of the aquisition of three dimensional topographic information by GPS was suggested.

• Geomechanics and Engineering
• /
• v.11 no.4
• /
• pp.515-530
• /
• 2016

In this paper, five different quantitative parameters were proposed for the characterization of the primary roughness which is the component of surface morphology that prevails during large strike-slip faults of more than 50 m. These parameters are mostly the anisotropic properties of rock surface morphology at various scales: (i) coefficient ($k_a$) and degree (${\delta}_a$) of apparent structural anisotropy of surface; (ii) coefficient ($k_r$) and degree (${\delta}_r$) of real structural anisotropy of surface; (iii) surface anisotropy function P(${\varphi}$); and (iv) degree of surface waviness ($W_s$). The coefficient and degree of apparent structural anisotropy allow qualifying the anisotropy/isotropy of a discontinuity according to a classification into four classes: anisotropic, moderately anisotropic/isotropic and isotropic. The coefficient and degree of real structural anisotropy of surface captures directly the actual surface anisotropy using geostatistical method. The anisotropy function predicts directional geometric properties of a surface of discontinuity from measurements in two orthogonal directions. These predicted data may subsequently be used to highlight the anisotropy/isotropy of the surface (radar plot). The degree of surface waviness allows qualifying the undulation of anisotropic surfaces. The proposed quantitative parameters allows their application at both lab and field scales.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2008.10a
• /
• pp.883-886
• /
• 2008

In optical information technology, an electro-controllable Photonic Band Gap (PBG) in a photonic crystal (PC) material is potentially useful for the manipulation of light. Despite a great deal of research on PBGs, the reliable use of electro-active PBG material systems is restricted to only a few cases because of the complex and limiting nature of the structures involved. Here, we propose a PBG system that uses a liquid crystal (LC) polymer composite. The composite is made of nematic LCs (NLCs) embedded in polymeric helical networks of photo-polymerized cholesteric LCs (CLCs). The composite film shows a large field-induced reversible color shift over 150 nm of the reflection band, due to the reorientational undulation of the helical axis, similar to the Helfrich effect.

• Journal of the Korean Society of Costume
• /
• v.36
• /
• pp.139-148
• /
• 1998

In order to know what sorts of features of neck form may be required to make plans for tight collars, the neck form of young japanese women were measured three demension-ally using GRASP(Grating Projection System for Profiling) and plaster torso. By the BASIC language in NEC computer and EXCEL program in MACINTOSHI computer, it became possible to draft a number of neck surface auomatically, therefore, we got analysis of a mass of subjects. Thed following results were obtained: 1. There was a large individual difference in the shape of neck, in particular, on the front and side curves of the neck base line, where the undulation of clavicular part of neck and inclination of shoulder are refracted. 2. When designing a stand collar, from the viewpoint of clothing strcture, it is important to grasp exactly the shapes of the neck, such as the line of the neck base, the neck gradient, back neck length, back neck width & girth. 3. According to the somatotypes(turing-over, standard, bending type), there were different the method of the basic collar pattern making.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.14 no.5
• /
• pp.1209-1217
• /
• 1994

This paper proposed transformation coefficients suitable to South Korea for the establishment of coordinate transformation system between Bessel and WGS84 ellipsoids. For this, the coordinates transformation algorithms concerned with parameter methods was developed, and global test network which has 15 astronomical points in South Korea were designed. Based on signals received from GPS, computed the geoid undulation by GPS/Leveling, and derived parameters(3-, 4-, 6-, and 7-parameter) for transformation between each ellipsoid, applied global networks to study the characteristics of transformation according to parameters. Through the successful application of 7-parameters derived in this study and 7-parameters proposed by DMA for map projection, transformation coefficients suitable to South Korea was proposed.

• Proceedings of the KSME Conference
• /
• 2001.11b
• /
• pp.664-669
• /
• 2001

The characteristics of dual coaxial jet which composed of inner supersonic nozzle of 26500 in constant expansion rate with 1.91 design Mach number and outer converging one with $40^{\circ}$ converging angle with the variation of outer nozzle stagnation pressures are experimentally investigated in this paper. In which the stagnation pressure for the inner supersonic nozzle is 750kPa thus, the inner jet leaving the nozzle is slightly underexpanded. The plenum pressures of outer nozzle are varied from 200 to 600kPa. Flow visualizations by shadowgraph method, impact pressure and centerline static pressure measurements of dual coaxial jet are presented. The results show that the presence of outer jet affects significantly the structures and pressure distributions of inner jet. And outer jet causes Mach disk which does not appear for the case of single jet stream. As the stagnation pressure of outer jet increases, impact pressure undulation is severe, but the average impact pressure keeps high far downstream.

• Tunnel and Underground Space
• /
• v.16 no.2 s.61
• /
• pp.146-155
• /
• 2006

The target slope of this study, formed during the construction of highway, is the very high infinite slope where sliding began along the discontinuity. Although an attempt was made to stabilize the upper part of the slope by installing the rock anchors, large scale failure was occurred at the lower part if the reinforced area. Afterwards, subsequent failures were observed two times. To investigate the cause of the failure, residual shear strength was measured by performing the direct shear test of rock specimen of the site. The anchor design was based on the pull-out test. Considering the slope surface where the undulation was severe and the variation of strength was very large, buttressing was used to obtain the required anchoring capacity.