• Bulletin of the Korean Space Science Society
• /
• 1993.10a
• /
• pp.17-17
• /
• 1993

The wall shear stress in the vicinity of end-to end anastomoses under steady flow conditions was measured using a flush-mounted hot-film anemometer(FMHFA) probe. The experimental measurements were in good agreement with numerical results except in flow with low Reynolds numbers. The wall shear stress increased proximal to the anastomosis in flow from the Penrose tubing (simulating an artery) to the PTFE: graft. In flow from the PTFE graft to the Penrose tubing, low wall shear stress was observed distal to the anastomosis. Abnormal distributions of wall shear stress in the vicinity of the anastomosis, resulting from the compliance mismatch between the graft and the host artery, might be an important factor of ANFH formation and the graft failure. The present study suggests a correlation between regions of the low wall shear stress and the development of anastomotic neointimal fibrous hyperplasia(ANPH) in end-to-end anastomoses. 30523 T00401030523 ^x Air pressure decay(APD) rate and ultrafiltration rate(UFR) tests were performed on new and saline rinsed dialyzers as well as those roused in patients several times. C-DAK 4000 (Cordis Dow) and CF IS-11 (Baxter Travenol) reused dialyzers obtained from the dialysis clinic were used in the present study. The new dialyzers exhibited a relatively flat APD, whereas saline rinsed and reused dialyzers showed considerable amount of decay. C-DAH dialyzers had a larger APD(11.70${\pm}$1.32mmHg/min)compared to CF dialyzers(4.32${\pm}$0.55mmHg/min)(p<0.05). However, there was no observable difference in the UFR between the two dialyzers. Neither APD nor UFR showed any significant increase with an increasing number of reuses for up to more than 20reuses. A substantial number of failures observed in APD(larger than 20mmHe/min)on the reused dialyzers(2 out of 40 CP and S out 26 C-DAK) were attributed to the Possible damage on the fibers. The CF 15-11 HFDs which failed APD test did not show changes in the UFR compared to normal dialyzers indicating that APD is a more sensitive test than UFR test to evaluate the integrity of the fibers. 30527 T00401030527 ^x For quantitative measurement of reflected light from a clinical diagnostic strip, a prototype old reflectance photometer was designed. The strip loader and cassette were made to obtain more accurate reflectance parameters. The strip was illuminated at 45˚c through optical fiber and the intensity of reflected light was determined at rectanguLat angle using a photodiode. The kubelka-munk coefficient and reflection optical density were determined ar four different wavelengths(500,550,570 and 610nm) for blood glucose strip. For higher concentration than 300mg/41 about glucose, a saturation state of abforbance was observed at 500,550 and 570nm. The correlation between glucose concentration and parameters was the best at 610nm. 30535 T00401030535 ^x Radiation-induced fibrosarcoma tumors were grown on the flanks of C3H mice. The mice were divided into two groups. One group was injected with Photofrin II, intravenously (2.5mg/kg body weight). The other group received no Photofrin II. Mice from both groups were irradialed for approximately 15 minutes at 100,300, or 500 mW/cm2 with the argon (488nm/514.5 nm), dye(628nm) and gold vapor (pulsed 628 nm) laser light. A photosensitizer behaved as an added absorber. Under our experimental conditions, the presence of Photolfrin II increased surface temperature by at least 40% and the temperature rise due to 300 mW/cm2 irradiation exceeded values for hyperthermia. Light and temperature distributions with depth were estimated by a computer model. The model demonstrated the influence of wavelength on the thermal process and proved to be a valuable tool to investigate internal temperature rise. 30536 T00401030536 ^x We investigated the structural geometry of thirty-eight Korean femurs. The purpose of this study is to identify major geometrical differences between Korean femurs 3nd others that we believe belong to Caucasians so that we would be able to get insights into the femoral component design that fits Asians including Koreans. We utilized computerized tomography (CT) images of femurs extracted from cadavers. The CT images were transformed into bitmap data by using a film scanner, and then analyzed by using a commercially available software called Image v.1.0 and a Macintosh IIci computer.The resulting data were compared with already published data. The major results show that the geometry of the Korean femurs is significantly different from that of Caucasians: (1) the anteversion angle and the canal flare index are greater by the amount of approximately 8˚ and 0.5, respectively, (2) the shape of the isthmus cross section is more round, and (3) the distance between the teaser trochanter and the proximal border of the isthmus is shelter by about 15 mm. The results suggested that the femoral component suitable for Asians should be different from the currently-used components designed and manufactured mostly by European or American companies. 30537 T00401030537 ^x It is well known that nonlinear propagation characteristics of the wave in the tissue may give very useful information for the medical diagnoisis. In this paper, a new method to detect nonlinear propagation characteristics of the internal vibration in the tissue for the low frequency mechanical vibration by using bispectral analysis is proposed. In the method, low frequency vibration of f0( = 100Hz) is applied on the surface of the object, and the waveform of the internal vibration x (t) is measured from Doppler frequency modulation of silmultaneously transmitted probing ultrasonic waves. Then, the bispectra of the signal x (t) at the frequencies (f0, f0) and (f0, 2f0) are calculated to estimate the nonlinear propagation characteristics as their magnitude ratio, w here since bispectrum is free from the gaussian additive noise we can get the value with high S/N. Basic experimental system is constructed by using 3.0 MHz probing ultrasonic waves and the several experiments are carried out for some phantoms. Results show the superiority of the proposed method to the conventional method using power spectrum and also its usefulness for the tissue characterization. 30541 T00401030541 ^x This paper describes the implementation of a computerized radial pulse diagnosis by aids of a clinical expert. On this base, we composed of the radial pulse diagnosis system in korean traditional medicine. The system composed of a radial pulse wave detection system and a radial pulse diagnosis system. With a detection system, we detected Inyoung and Cheongu radial pulse wave and processed it. Then, we have got the characteristic parameters of radial pulse wave and also quantified that according to the method of Inyoung-Cheongu Comparison Radial Pulse Diagnosis. We defined the jugement standard of radial pulse diagnosis system and then we confirmed the possibility for realization of automatic radial pulse diagnosis in korean traditional medicine. 30545 T00401030545 ^x Microspheres are expected to be applied to biomedical areas such as solid-phase immunoassays, drug delivery systems, immunomagnetic cell separation. To synthesize microspheres for biomedical application, "two stage shot growth method" was developed. The uniformity ratio of synthesized microspheres was always smaller than 1.05. And the surface charge density (or the number of ionizable functional groups) of the microspheres synthesized by "two stage shot growth method" was 6~13 times higher than that of the microspheres synthesized by conventional seeded batch copolymerization. As a previous step for biomedical application, adsorption experiments of bovine albumin on microspheres were carried out under various conditions. The maximum adsorbed amount was obtained in the neighborhood of pH 4.5. Isoelectric point of bovine albumin is pH 5.0, so experimental result shows that it shifted to acid area. The adsorption isotherm was obtained, the plateau region was always reached at 2.Og/L (bulk concentration of bovine albumin).The effect of the kind and the amount of surface functional group was also examined. 30575 T00401030575 ^x A medical image workstation was developed using multimedia technique. The system based on PC-486DX was designed to acquire medical images produced by medical imaging instruments and related audio information, that is, doctors' reporting results. Input information was processed and analyzed, then the results were presented in the form of graph and animation. All the informations of the system were hierarchically related with the image as the apex. Processing and analysis algorithms were implemented so that the diagnostic accuracy could be improved. The diagnosed information can be transferred for patient diagnosis through LAN(local area network). 30592 T00401030592 ^x In the conventional infrared imaging system, complex infrared lens systems are usually used for directing collimated narrow infrared beams into the high speed 2-dimensional optic scanner. In this paper, a simple reflective infrared optic system with a 2-dimensional optic scanner is proposed for the realization of medical infrared thermography system. It has been experimentally proven that the intfrared thermography system composed of the proposed optic system has the temperature resolution of 0.1˚c under the spatial resolution of lmrad, the image matrix size of 256 X 240, and tile imaging time of 4 seconds. 30593 T00401030593 ^x In this paper, MIIS (Medical Image Information System) has been designed and implemented using INGRES RDBMS, which is based on a client/server architecture. The implemented system allows users to register and retrieve patient information, medical images and diagnostic reports. It also provides the function to display these information on workstation windows simultaneously by using the designed menu-driven graphic user interface. The medical image compression/decompression techniques are implemented and integrated into the medical image database system for the efficient data storage and the fast access through the network. 30594 T00401030594 ^x In this paper, computerized BEAM was implemented for the space domain analysis of EEG. Trans-formation from temporal summation to two-dimensional mappings is formed by 4 nearest point inter-polaton method. Methods of representation of BEAM are two. One is dot density method which classify brain electrical potential 9 levels by dot density of gray levels and the other is colour method which classify brain electrical 12 levels by red-green colours. In this BEAM, instantaneous change and average energy distribution over any arbitrary time interval of brain electrical activity could be observed and analyzed easily. In the frequency domain, the distribution of energy spectrum of a special band can easily be distinguished normality and abnormality. 30608 T00401030608 ^x Laboratory information system (LIS) is a key tool to manage laboratory data in clinical pathology. Our department has developed an information system for routine hematology using down-sized computer system. We have used an IBM 486 compatible PC with 16MB main memory, 210 MB hard disk drive, 9 RS-232C port and 24 pin dot printer. The operating system and database management system were SCO UNIX and SCO foxbase, respectively. For program development, we used Xbase language provided by SCO foxbase. The C language was used for interface purpose. To make the system use friendly, pull-down menu was used. The system connected to our hospital information system via application program interface (API), so the information related to patient and request details is automatically transmitted to our computer. Our system interfaced with fwd complete blood count analyzers(Sysmex NE-8000 and Coulter STKS) for unidirectional data tansmission from analyzer to computer. The authors suggests that this system based on down-sized computer could provide a progressive approach to total LIS based on local area network, and the implemented system could serve as a model for other hospital's LIS for routine hematology. 30609 T00401030609 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed a composite that is consisted of calcium phosphate and collagen. To use as the structural matrix of the composite, collagen was purified from human umbilical cord. The obtained collagen was treated by pepsin to remove telopeptides, and finally, the immune-free atelocollagen was produced: The cross linked atelocollagen was highly resistant to the collagenase induced collagenolysis. The cross linked collagen demonstrated an improved tensile strength. 30618 T00401030618 ^x This paper is a study on the design of adptive filter for QRS complex detection. We propose a simple adaptive algorithm to increase capability of noise cancelation in QRS complex detection with two stage adaptive filter. At the first stage, background noise is removed and at the next stage, only spectrum of QRS complex components is passed. Two adaptive filters can afford to keep track of the changes of both noise and QRS complex. Each adaptive filter consists of prediction error filter and FIR filter The impulse response of FIR filter uses coefficients of prediction error filter. The detection rates for 105 and 108 of MIT/BIH data base were 99.3% and 97.4% respectively. 30619 T00401030619 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed and produced a composite that is consisted of calcium phosphate and collagen. Human umbilical cord origin pepsin treated type I atelocollagen was used as the structural matrix, by which sintered or non-sintered carbonate apatite was encapsulated to form an inorganic-organic composite. With cross linking atelocollagen by UV ray irradiation, the resistance to both compressive and tensile strength was increased. Collagen degradation by the collagenase induced collagenolysis was also decreased. 30620 T00401030620 ^x We have developed a monoleaflet polymer valve as an inexpensive and viable alternative, especially for short-term use in the ventricular assist device or total artificial heart. The frame and leaflet of the polymer valve were made from polyurethane, To evaluate the hemodynamic performance of the polymer valve a comparative study of flow dynamics past a polymer valve and a St. Jude Medical prosthetic valve under physiological pulsatile flow conditions in vitro was made. Comparisons between the valves were made on the transvalvular pressure drop, regurgitation volume and maximum valve opening area. The polymer valve showed smaller regurgitation volume and transvalvular pressure drop compared to the mechanical valve at higher heart rate. The results showed that the functional characteristics of the polymer valve compared favorably with those of the mechanical valve at higher heart rate. 30621 T00401030621 ^x Explosive evaporative removal process of biological tissue by absorption of a CW laser has been simulated by using gelatin and a multimode Nd:YAG laser. Because the point of maximun temperature of laser-irradiated gelatin exists below the surface due to surface cooling, evaporation at the boiling temperature is made explosively from below the surface. The important parameters of this process are the conduction loss to laser power absorption (defined as the conduction-to-laser power parameter, Nk), the convection heat transfer at the surface to conduction loss (defined as Bi), dimensionless extinction coefficient (defined as Br.), and dimensionless irradiation time (defined as Fo). Dependence of Fo on Nk and Bi has been observed by experiment, and the results have been compared with the numerical results obtained by solving a 2-dimensional conduction equation. Fo and explosion depth (from the surface to the point of maximun temperature) are increased when Nk and Bi are increased.To find out the minimum laser power for explosive evaporative removal process, steady state analysis has been also made. The limit of Nk to induce evaporative removal, which is proportional to the inverse of the laser power, has been obtained. 30622 T00401030622 ^x N1 and N2 gross neural action potentials were measured from the round window of the guinea pig cochlea at the onset of the acoustic stimuli. N1-N2 audiograms were made by means of regulating stimulant intensities in order to produce constant N1-N2 potentials as criteria for different input tone pip frequencies. The lowest threshold was measured with an input tone pip I5 dB SPL in intensity and 12 KHz in frequency when the animal was in normal physiological condition. The procedure of experimental measurements is explained in detail. This experimental approach is very useful for the investigation of the Cochlear function. Both noN1inear and active functions of the Cochlea can be monitored by N1-N2 audiograms. 30623 T00401030623 ^x In electrical impedance tomography(EIT), we use boundary current and voltage measurements toprovide the information about the cross-sectional distribution of electrical impedance or resistivity. One of the major problems in EIT has been the inaccessibility of internal voltage or current data in finding the internal impedance values. We propose a new image reconstruction method using internal current density data measured by NMR. We obtained a two-dimensional current density distribution within a phantom by processing the real and imaginary MR images from a 4.77 NMR machine. We implemented a resistivity mage reconstruction algorithm using the finite element method and sensitivity matrix. We presented computer simulation results of the mage reconstruction algorithm and furture direction of the research. 30624 T00401030624 ^x A new method of digital image analysis technique for discrimination of cancer cell was presented in this paper. The object image was the Thyroid eland cells image that was diagnosed as normal and abnormal (two types of abnormal: follicular neoplastic cell, and papillary neoplastic cell), respectively. By using the proposed region segmentation algorithm, the cells were segmented into nucleus. The 16 feature parameters were used to calculate the features of each nucleus. A9 a consequence of using dominant feature parameters method proposed in this paper, discrimination rate of 91.11% was obtained for Thyroid Gland cells. 30625 T00401030625 ^x An electrical stimulator was designed to induce locomotion for paraplegic patients caused by central nervous system injury. Optimal stimulus parameters, which can minimize muscle fatigue and can achieve effective muscle contraction were determined in slow and fast muscles in Sprague-Dawley rats. Stimulus patterns of our stimulator were designed to simulate electromyographic activity monitored during locomotion of normal subjects. Muscle types of the lower extremity were classified according to their mechanical property of contraction, which are slow muscle (msoleus m.) and fast muscle (medial gastrocneminus m., rectus femoris m., vastus lateralis m.). Optimal parameters of electrical stimulation for slow muscles were 20 Hz, 0.2 ms square pulse. For fast muscle, 40 Hz, 0.3 ms square pulse was optimal to produce repeated contraction. Higher stimulus intensity was required when synergistic muscles were stimulated simultaneously than when they were stimulated individually. Electrical stimulation for each muscle was designed to generate bipedal locomotion, so that individual muscles alternate contraction and relaxation to simulate stance and swing phases. Portable electrical stimulator with 16 channels built in microprocessor was constructed and applied to paraplegic patients due to lumbar cord injury. The electrical stimulator restored partially gait function in paraplegic patients. 30626 T00401030626 ^x Two-Dimensional modelling of the Cochlear biomechanics is presented in this paper. The Laplace partial differential equation which represents the fluid mechanics of the Cochlea has been transformed into two-dimensional electrical transmission line. The procedure of this transformation is explained in detail. The comparison between one and two dimensional models is also presented. This electrical modelling of the basilar membrane (BM) is clearly useful for the next approach to the further. Development of active elements which are essential in the producing of the sharp tuning of the BM. This paper shows that two-dimension model is qualitatively better than one-dimensional model both in amplitude and phase responses of the BM displacement. The present model is only for frequency response. However because the model is electrical, the two-dimensional transmission line model can be extended to time response without any difficult. 30627 T00401030627 ^x A method has been proposed for the fully automatic detection of left ventricular endocardial boundary in 2D short axis echocardiogram using geometric model. The procedure has the following three distinct stages. First, the initial center is estimated by the initial center estimation algorithm which is applied to decimated image. Second, the center estimation algorithm is applied to original image and then best-fit elliptic model estimation is processed. Third, best-fit boundary is detected by the cost function which is based on the best-fit elliptic model. The proposed method shows effective result without manual intervention by a human operator. 30628 T00401030628 ^x The intelligent trajectory control method that controls moving direction and average velocity for a prosthetic arm is proposed by pattern recognition and force estimations using EMG signals. Also, we propose the real time trajectory planning method which generates continuous accelleration paths using 3 stage linear filters to minimize the impact to human body induced by arm motions and to reduce the muscle fatigue. We use combination of MLP and fuzzy filter for pattern recognition to estimate the direction of a muscle and Hogan's method for the force estimation. EMG signals are acquired by using a amputation simulator and 2 dimensional joystick motion. The simulation results of proposed prosthetic arm control system using the EMf signals show that the arm is effectively followed the desired trajectory depended on estimated force and direction of muscle movements. 30638 T00401030638 ^x A new neural network architecture for the recognition of patterns from images is proposed, which is partially based on the results of physiological studies. The proposed network is composed of multi-layers and the nerve cells in each layer are connected by spatial filters which approximate receptive fields in optic nerve fields. In the proposed method, patterns recognition for complicated images is carried out using global features as well as local features such as lines and end-points. A new generating method of matched filers representing global features is proposed in this network. 30659 T00401030659 ^x An implementation scheme of the magnetic nerve stimulator using a switching mode power supply is proposed. By using a switching mode power supply rather than a conventional linear power supply for charging high voltage capacitors, the weight and size of the magnetic nerve stimulator can be considerably reduced. Maximum output voltage of the developed magnetic nerve stimulator using the switching mode power supply is 3,000 volts and switching time is about 100 msec. Experimental results or human nerve stimulations using the developed stimulator are presented. 30768 T00401030768 ^x In this paper, we describe the design methodology and specifications of the developed module-based bedside monitors for patient monitoring. The bedside monitor consists of a main unit and module cases with various parameter modules. The main unit includes a 12.1" TFT color LCD, a main CPU board, and peripherals such as a module controller, Ethernet LAN card, video card, rotate/push button controller, etc. The main unit can connect at maximum three module cases each of which can accommodate up to 7 parameter modules. They include the modules for electrocardiograph, respiration, invasive blood pressure, noninvasive blood pressure, temperature, and SpO2 with Plethysmograph.

• Journal of Distribution Research
• /
• v.14 no.2
• /
• pp.67-95
• /
• 2009

The purpose of this study is to empirically examine the transference of trust process, an important factor to consumer's purchase decision-making. Even though several researchers have discussed the trust transference process, there is no research related to this concept. Specifically we have focused on the transference of trust from the retailer to low involvement private label (PL) products. PL products were chosen as transference of trust occurs under ambiguity due to lack of information about the product and their manufacturer. PL products provide relatively less information than national brand (NB) products. In addition, retailers have been rapidly expanding their PL product categories. To identify the theoretical and empirical limitations of prior studies, we discuss several theories explaining the transference of trust: 'Balance theory' and 'availability heuristic' in transference of cognitive trust; 'affective transference' and 'affect as information' in transference of affective trust. An empirical test was performed. A self completion questionnaire was developed and administered to a convenience sample of PL users. 206 usable questionnaire were received. The results show that the transference of trust plays a mediating role linking the retailer to the manufacturer and to the product. Although our model, which included the transference process of trust as a mediating effect, did not improve the competitive model, the coefficients of the respective paths were found to be better. This study confirms the transference of cognitive trust from the retailer to both the manufacturer and the product, but not for affective trust. We offer the explanation that PL products may tend to have affective trust resulting from brand familiarity but not to their PL manufacturers.

• Korean Journal of Poultry Science
• /
• v.40 no.1
• /
• pp.25-29
• /
• 2013

This study was conducted to evaluate the antimicrobial and antioxidant effects of ripened medicinal herb extracts from wood vinegar. The wood vinegar was collected from heated oaks. The Allium sativum (AS), Atractylodes ovate (AO), Cin-namomum zeylanicum (CZ), Coptidis rhizome (CR), Houttuynia cordata (HC), Phellodendron chinense (PC) and Syzygium aromaticum (SA) extracts were collected using wood vinegar, and they were ripened under room temperature for 50 days. All ripened medicinal herb extracts were used to test the antimicrobial and antioxidant activities. For the Lactobacillus, clear zone of 6 different medicinal herb except for CR ranged from 1.28 to 1.63 mm. 3.30 and 3.48 mm of clear zone were determined when CZ and SA were applied to Salmonella and E. coli, respectively (p<0.05), and they showed the largest clear zone as compared to other herbs. The clear zones of CR for Salmonella and E. coli were 2.21 and 3.34 mm, and each clear zone of CR was smaller than that of CZ (p<0.05) but was similar to that of SA (p>0.05). The amount of polyphenol and flavonoid was the highest in SA and CR, and they were 4.28 and 0.38 mg/mL, respectively (p<0.05). The CR shown 0.38 mg/mL flavonoid, had the highest DPPH, and it was 0.41 mM. The DPPH of HZ was significantly lowered in accordance with high amount of polyphenol and flavonoid, 2.56 and 0.20 mg/mL (p<0.05). In conclusion, CZ, SA, and CR showed high antimicrobial and antioxidant potentials, and therefore, may be used as alternatives to antibiotics for poultry diets.

• Asia pacific journal of information systems
• /
• v.22 no.3
• /
• pp.53-74
• /
• 2012

A challenge in fostering virtual communities is the continuous supply of knowledge, namely members' willingness to contribute knowledge to their communities. Previous research argues that giving away knowledge eventually causes the possessors of that knowledge to lose their unique value to others, benefiting all except the contributor. Furthermore, communication within virtual communities involves a large number of participants with different social backgrounds and perspectives. The establishment of mutual understanding to comprehend conversations and foster knowledge contribution in virtual communities is inevitably more difficult than face-to-face communication in a small group. In spite of these arguments, evidence suggests that individuals in virtual communities do engage in social behaviors such as knowledge contribution. It is important to understand why individuals provide their valuable knowledge to other community members without a guarantee of returns. In virtual communities, knowledge is inherently rooted in individual members' experiences and expertise. This personal nature of knowledge requires social interactions between virtual community members for knowledge transfer. This study employs the social capital theory in order to account for interpersonal relationship factors and identity theory for individual and group factors that may affect knowledge contribution. First, social capital is the relationship capital which is embedded within the relationships among the participants in a network and available for use when it is needed. Social capital is a productive resource, facilitating individuals' actions for attainment. Nahapiet and Ghoshal (1997) identify three dimensions of social capital and explain theoretically how these dimensions affect the exchange of knowledge. Thus, social capital would be relevant to knowledge contribution in virtual communities. Second, existing research has addressed the importance of identity in facilitating knowledge contribution in a virtual context. Identity in virtual communities has been described as playing a vital role in the establishment of personal reputations and in the recognition of others. For instance, reputation systems that rate participants in terms of the quality of their contributions provide a readily available inventory of experts to knowledge seekers. Despite the growing interest in identities, however, there is little empirical research about how identities in the communities influence knowledge contribution. Therefore, the goal of this study is to better understand knowledge contribution by examining the roles of social capital and identity in virtual communities. Based on a theoretical framework of social capital and identity theory, we develop and test a theoretical model and evaluate our hypotheses. Specifically, we propose three variables such as cohesiveness, reciprocity, and commitment, referring to the social capital theory, as antecedents of knowledge contribution in virtual communities. We further posit that members with a strong identity (self-presentation and group identification) contribute more knowledge to virtual communities. We conducted a field study in order to validate our research model. We collected data from 192 members of virtual communities and used the PLS method to analyse the data. The tests of the measurement model confirm that our data set has appropriate discriminant and convergent validity. The results of testing the structural model show that cohesion, reciprocity, and self-presentation significantly influence knowledge contribution, while commitment and group identification do not significantly influence knowledge contribution. Our findings on cohesion and reciprocity are consistent with the previous literature. Contrary to our expectations, commitment did not significantly affect knowledge contribution in virtual communities. This result may be due to the fact that knowledge contribution was voluntary in the virtual communities in our sample. Another plausible explanation for this result may be the self-selection bias for the survey respondents, who are more likely to contribute their knowledge to virtual communities. The relationship between self-presentation and knowledge contribution was found to be significant in virtual communities, supporting the results of prior literature. Group identification did not significantly affect knowledge contribution in this study, inconsistent with the wealth of research that identifies group identification as an important factor for knowledge sharing. This conflicting result calls for future research that examines the role of group identification in knowledge contribution in virtual communities. This study makes a contribution to theory development in the area of knowledge management in general and virtual communities in particular. For practice, the results of this study identify the circumstances under which individual factors would be effective for motivating knowledge contribution to virtual communities.

• Tuberculosis and Respiratory Diseases
• /
• v.44 no.1
• /
• pp.154-161
• /
• 1997

Background : Although the long term adverse effects of cigarette smoking on health are well known, the acute possible detrimental effects of smoking on pulmonary or cardiovascular function, especially when these systems are stressed by the metabolic demands of exercise, have not been well studied The purpose of this study is to determine the acute action of cigarette smoking on cardiopulmonary function under stress. Method : Twenty -one healthy smoking subjects were studied. Before exrecise testing, history taking, physical examination and baseline studies, including CBC, chest PA, PFT and EKG, were done. The subjects performed an incremental bicycle exercise test to exhaustion on two occasions, one without smoking and the other after smoking 5 cigarettes/h for 2 hours. All indices of P.F.T. and bicycle ergometry were compared between before and after smoking. Results : 1. $VO_2$max and $O_2$ pulse showed significant decrease in smoking day. 2. Although there were no significant differences, anaerobic threshold showed a tendency of decrease and HRmax showed that of increase in smoking day. 3. P.F.T. and respiratory indices showed no significant change io smoking day. Conclusion : Cigarette smoking has immediate adverse effect, especially on the cardiovascular system rather than the respiratory system. These results would be due to the effect of elevated HbCO and/or impaired blood flow in response to the exercise stimulus.

• Culinary science and hospitality research
• /
• v.22 no.3
• /
• pp.66-78
• /
• 2016

The purpose of this study was to provide hotel bakery organizations with useful information for human resources management based on a substantial clarification of the relationship and correlation of hotel bakery employees' self-leadership, self-efficacy, and organizational commitment. Resources were gathered from June 20, 2015 to July 10, 2015 by distributing a total of 500 surveys, from which 377 were collected. Excluding 23 survey forms not suitable for the analysis, 354 survyes were processed through factor analysis, reliability test, and multivariant structural analysis using SPSS 18.0 and AMOS 18.0 to verify the hypotheses. The findings of the analysis can be summarized as follows: first, behavior-centered strategies, natural compensation, and constructive thinking strategies had a significantly positive impact on self-efficacy. Second, in the analysis of impact of self-efficacy on organizational commitment, it was significant for emotional immersion, but did not have a significantly positive impact on normative immersion. Third, in the relationship between self-leadership and organizational commitment, behavior-centered strategies and natural compensation did not have a significant impact on emotional immersion. However, constructive thinking strategies had a significant impact. The following implications can be derived based on the above findings: this study implies the possibility of future studies on the variables of self-efficacy as it set behavior-centered strategies, natural compensation, and constructive thinking strategies as the preliminary factors under hotel bakery employees' self-leadership; and it analyzed the causality of each factor with emotional immersion and normative immersion as the subordinate factors of self-efficacy and organizational commitment to show that self-leadership and self-efficacy of hotel bakery employees based on emotional immersion and normative immersion can stably improve the organization of hotel bakeries.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.40 no.12
• /
• pp.1781-1786
• /
• 2011

This study was conducted to investigate the cause of microbiological contamination in yogurt and evaluate the effect of physicochemical treatment on the growth inhibition of Hanseniaspora uvarum isolated from yogurt. The yeast strain Hanseniaspora uvarum Y1 was subjected to heat and pH treatments. H. uvarum Y1 was killed at $70^{\circ}C$ and $80^{\circ}C$ after 15 min and survived in a wide pH range from pH 2 to 9. However, it did not survive under pH 1 and over pH 10. In a disk diffusion susceptibility test on H. uvarum Y1, a clear zone (5 mm) of growth inhibition was observed upon treatment with electrolyzed water. The effect of ozone gas on the growth of H. uvarum Y1 was evaluated by viable cell count. Initial cell numbers of $10^2$ and $10^3$ CFU/mL of H. uvarum Y1 were completely killed by treatment for 10 and 30 min, respectively. H. uvarum Y1 was also sterilized by microwave treatment for 1 min. When treated with gamma-irradiation, the rate of killing of H. uvarum Y1 was proportional to the irradiation dose. and complete killing occurred at a dose of 50 kGy.

• Journal of Korea Water Resources Association
• /
• v.44 no.10
• /
• pp.797-807
• /
• 2011

Phenomenon of vegetation recruitment on the sand bar is drastically rising in the streams and rivers in Korea. In the 1960s prior to industrialization and urbanization, most of the streams were consisted of sands and gravels, what we call, 'White River'. Owing to dam construction, stream maintenance, etc. carried out since the '70s, the characteristic of flow duration and sediment transport have been disturbed resulting in the abundance of vegetation in the waterfront, that is, 'Green River' is under progress. This study purposed to identify the correlation among water level, water temperature, rainfall, soil moisture and soil texture out of the factors which give an effect on the vegetation recruitment on the sand bar of unregulated stream. To this purpose, this study selected the downstream of Naeseong Stream, one of sand rivers in Korea, as the river section for test and conducted the monitoring and analysis for 289 days. In addition, this study analyzed the aerial photos taken from 1970 to 2009 in order to identify the aged change in vegetation from the past to the present. The range of the tested river section was 361 m in transverse length and about 2 km in longitudinal length. According to the survey analysis, the tested river section in Naeseong Stream was a gaining river showing the higher underground-water level by 20~30 m compared to Stream water level. The difference in the underground water temperature was less than $5^{\circ}C$ by day and season and the Stream temperature did not fall to $10^{\circ}C$ and less from May when the vegetation germination begins in earnest. The impact factor on soil moisture was the underground water level in the lower layer and the rainfall in the upper layer and it was found that all the upper and lower layer were influenced by soil particle size. The soil from surface to 1 m-underground out of 6 soil moisture-measured points was sand with the $D_{50}$ size of 0.07~1.37 mm and it's assumed that the capillary height possible in the particle size would reach around 14~43 cm. On the other hand, according to the result of space analysis on the tested river section of unregulated stream for 40 years, it was found that the artificial disturbance and drought promoted the vegetation recruitment and the flooding resulted in the frequency extinction of vegetation communities. Even though the small and large scales of recruitment and extinction in vegetation have been repeated since 1970, the present vegetation area increased clearly compared to the past. It's found that the vegetation area is gradually increasing over time.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.58 no.4
• /
• pp.416-423
• /
• 2013

Germination is controlled by internal factors of seeds and external factors such as water, temperature and light. We investigated the relationship between germination characteristics of four waxy rice cultivars and patterns of water uptake, antioxidant enzymes and free soluble sugars during early imbibition. Seed viabilities by tetrazolium test of four different rice cultivars were higher than 95% and germination rates of the hulled rice seeds were on 95% average. However, germination rate of intact rice among four cultivars showed a big difference depending on temperature. Water uptake of hulled and intact rice seeds during imbibition reached a stationary phase at around 30% moisture content. Although rates of water uptake were faster in hulled rice and high temperature than intact rice and low temperature condition, difference of those among cultivars was greater under low temperature than high temperature. The time required for rice seeds to uptake 30% water was negatively correlated with percentage of germination, germination energy, germination speed and mean germination time. Guaiacol peroxidase activity at 24h of imbibition was correlated with germination energy and germination speed but not percentage of germination. Catalase activity, soluble protein and maltose concentration at 24h of imbibition were not correlated with characteristics of germination. These results suggest that a time required for rice seeds to uptake 30% of water significantly correlated with germination and guaiacol peroxidase activity during early imbibition plays an important role in initiation of germination.

• The Korean Journal of Pesticide Science
• /
• v.17 no.4
• /
• pp.460-467
• /
• 2013

This study was conducted to reduce the using amount of chemical fungicides for the control of red-pepper Phytophthora blight. Effect of combination application of two microbial fungicides and two chemical fungicides for the control of red-pepper Phytophthora blight was examined in vitro, in greenhouse and under field conditions. Each microbial fungicides and chemical fungicides was two-fold diluted and mixed-soil drenched. In the greenhouse pot assay, the mixed application of B. pumilus QST2808 and a mixture of dimethomorph + ethaboxam (De) among four mixed applications of two microbial fungicides (B. pumilus QST2808, P. polymyxa AC-1) and two chemical fungicides showed the highest control effect against Phytophthora blight. Also, control effect of mixed application of B. pumilus QST2808 and De was similar to that of single application of De (dimethomorph + ethaboxam) or Mo (mancozeb + oxadixyl). In the field test, when the microbial fungicides (B. pumilus QST2808, P. polymyxa AC-1) and the chemical fungicide(De) for the control of Phytophthora blight of red pepper were mixed-soil drenched four times at 7~10 day-intervals, the control values were in the range of 78.8% to 82.0%. On the other hand when each of the two chemical fungicides (De, Mo) were soil drenched four times at 7~10 day-intervals, the control value were 65.7% to 85.8%. Consequently, the mixed application of the microbial fungicides and chemical fungicides could be recommended as a control method for reducing the using amount of chemical fungicides.