• Journal of Ocean Engineering and Technology
• /
• v.8 no.1
• /
• pp.96-104
• /
• 1994

The use of advanced composite materials has grown in recent years in aerospace and other structures. Out of various kinds of repairing methods the one selecteh for this study is an idealized case which simulates a situation where a damaged laminate has been repaired by drilling a hole and therefter plugging the hole with reinforcement. Two typesof reinforcement are investigated ;adhesively bonged plug reinforcement or snug-fit unbonded plug in the hole. For each case of reinforcement, four different sizes of hole diameter and three types of reinforcing material(steel, aluminum, plexiglass) are employed for investigation. The experiment are mainloy forced on the evaluation of ultimate strength of laminate with reinforced hole in comparison to its counterpart with the open hole.

• Computers and Concrete
• /
• v.5 no.6
• /
• pp.525-544
• /
• 2008

In this research, the self-centering effect in precast and prestressed reinforced concrete structures was investigated experimentally. The reinforced concrete beams and columns were precast and connected by post-tensioning tendons passing through the center of the beams as well as the panel zone of the connections. Three beam-to-interior-column connections were constructed to investigate parameters such as beam to column interfaces (steel on steel or plastic on plastic), energy dissipating devices (unbonded buckling restrained steel bars or steel angles) and the spacing of hoops in the panel zone. In addition to the self-centering effect, the shear strength in the panel zone of interior column connections was experimentally and theoretically evaluated, since the panel zone designed by current code provisions may not be conservative enough to resist the panel shear increased by the post-tensioning force.

• Proceedings of the Acoustical Society of Korea Conference
• /
• 1998.06e
• /
• pp.247-250
• /
• 1998

The scattering of plane ultrasonic waves by the nuclear fuel pin of liquid metal reactor in sodium is studied. According to the internal composition in the cladding tube, the fuel pin has three cross sections, i.e. helium gas plenum, sodium-filled section, and fuel insertion section. The scattering spectra for each section of the fuel pin are different. The circumnavigating ultrasonic waves of each section are analyzed by the resonance scattering method. The whispering gallery wave modes are generated in the sodium-filled plenum section and the fuel rod insertion section with a sodium-gap. The circumferential wave modes are propagated in the cladding tube of the helium gas plenum section. The annular gap between the cladding tube and metal uranium pellet rod affects the scattering spectra. The different propagation characteristics can be utilized for the nondestructive method of detecting the unbonded area and measuring the level of the sodium-filled section of the fuel pin.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2006.05a
• /
• pp.178-181
• /
• 2006

The purpose of this study is to investigate the inelastic behavior of precast segmental prestressed concrete bridge piers. A computer program, named RCAHEST (Reinforced Concrete Analysis in Higher Evaluation System Technology), for the analysis of reinforced concrete structures was used. Material nonlinearity is taken into account by comprising tensile, compressive and shear models of cracked concrete and a model of reinforcing steel. An unbonded tendon element based on the finite element method, that can represent the interaction between tendon and concrete of prestressed concrete member, is used. A joint element is newly developed to predict the inelastic behaviors of segmental joints. The proposed numerical method for the inelastic behavior of precast segmental prestressed concrete bridge piers is verified by comparison with reliable experimental results.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2010.05a
• /
• pp.83-84
• /
• 2010

Precast beam column joints with thru-connectors are developed from precedent study. The seismic performance is evaluated by experimental method. The test results of the precedent study showed that failure modes for all specimens were a compression failure by characteristics of unbonded tendon. Thus, variable considered in the research program for a tensile failure include the use of dog-boned longitudinal steel and concrete confined with steel spirals. The analysis of structural characteristics and evaluation of seismic performance of specimens was conducted by the experimental way. Comparison of result with the test specimens indicates that seismic performance is higher than the precedent study due to concrete confinement effect from steel spirals.

• Proceedings of the Earthquake Engineering Society of Korea Conference
• /
• 2002.09a
• /
• pp.274-281
• /
• 2002

In this study a analytical model for a structure with buckling-restrained unbonded knee-braces is proposed, and a performance-based seismic design procedure for such a system Is provided. The proposed structure system has advantage of simplifying the structural design procedure in that the hinge-connected main structural members, such as beams and columns, are designed only for gravity loads, and all the lateral seismic load is resisted by the braces. The design procedure is based on the concept of equivalent damping, and is implemented to the capacity spectrum method. Parametric study is performed with design variables such as yield stress and cross-sectional area of knee-braces to find out proper slope of the braces.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1997.04a
• /
• pp.635-642
• /
• 1997

This research focused on the development of concrete overlay and test, which was conducted at 88 Highway 105k, 2 lanes of 290 m. The field application test consists of 6 cm and 10 cm bonded concrete overlay and 25 cm unbonded concrete overlay, using the slag cement for opening lanes for traffic early. The overlay were placed in a day. The whole period of traffic closing wes 8 day and it was reopened to traffic after concrete overlay has cured for 3 day. 5 cracks were founded when the field test section was investigated after 1 month, but all these may not make significant problems to overlay because these initiated and growed at the same line of repair section. The rideability and skid resistance become much better like in the new pavement after overlay. The structural capacity against deflection was much. which were verified by FWD(Falling Weight Deflectometer). The field test section is being used in a good condition and the results of field application and pavement performance analysis are encouraging. This rehabilitation methods may be adopted in Korea after a more field performance verifications.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2002.04a
• /
• pp.200-207
• /
• 2002

Energy dissipation capacity and earthquake responses of steel structures installed with unbonded braces(UB) were investigated. Nonlinear dynamic time history analyses were carried out to investigate the seismic response of multi-story model structures with UB having various size and strength. Various techniques were applied to determine proper story-wise distribution of UB in multi-story structures. The analysis results show that the maximum displacements of structures generally decrease as the stiffness of UB increases. However there are cases that the maximum displacement and accumulated damage increases as the stiffness of UB increases, which needs to be checked before deciding proper amount of UB.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2006.11a
• /
• pp.193-196
• /
• 2006

Unlike external bonded plate or carbon fiber, the external unbonded strengthening has some advantages in speed and simplicity of installation. It is not required surface preparations and not affected by environmental conditions. A set of six laboratory tests on RC beams strengthened using the technique are reported, results compared with non-strengthened specimens. The main test parameters are the cross-sectional area of the high-tension bar and the distance of stirrups. Test result show that the beams reinforced are superior to reference specimens, especially for the strength and deformation capacity. Also, it is shown that good efficiencies can be achived in shear strength of the beam.

• Journal of the Korean Society for Precision Engineering
• /
• v.16 no.3 s.96
• /
• pp.208-214
• /
• 1999

The purpose of this paper is to develop a profile modification technique of spur gears and its computer program for the prevention of gear tooth overlap. In the gear system, tooth overlap produces an impact at the initial contact of some tooth pairs. In this analysis, contact surface was assumed to be unbonded and frictionless under small deformation and stain. The problem is formulated by a variational statement with inequality constraint. Tooth load sharing is obtained by the application of contact theory, and overlap is known by the analysis of deformation. After carrying out the profile modification of gear tooth, we verified the reasonable results.