• Journal of Electrical Engineering and Technology
• /
• v.1 no.1
• /
• pp.106-109
• /
• 2006

In this paper, the design and characteristics of a novel ultrasonic motor are investigated. Such a motor is appropriate far use in the optical zoom or auto focusing functions of the lens system in mobile phones. Its design and simulation of performances are carried out by FEM commercial software (ATILA). The shape of the motor is similar to a square without one side, on which an optical lens can be mounted. Two sheets of piezoelectric ceramics are adhered to both sides of two legs of the elastic body, respectively To drive the ultrasonic motor, the voltage is applied to two sheets of piezoelectric ceramics bonded to one leg. The rotation direction can be easily changed by switching the piezoelectric sheets bonded to the other leg, to which voltage is applied. A proto type of the motor is fabricated and its outer size is $10^*10^*2[mm3]$ including the camera lens of which the diameter is 7.5(mm). Its power consumption is about 0.3[W] and the speed of rotation is adjustable from 10 to 200[rpm] according to the applied voltage

• Proceedings of the KSME Conference
• /
• 2000.11b
• /
• pp.732-737
• /
• 2000

The purpose of this study is to compare the SMD(Sauter mean diameter) with different vibrant plates. Each vibrant plates have different surface roughness. Also liquid film thickness are measured for explanation how to concern atomization. Ultrasonic waves is used for vibration. Immersion liquid method is used for the measure of SMD and also liquid film thickness is measured using of point needle method. Distilled water and gasoline fuel are used to liquids. Supplied liquid flow rates are $18{\sim}296cc/min$. Centerline average roughness of vibrant plates are 0.5, 2.0, 4.7, $9.5\;{\mu}m$ and diameter of vibrant plate is 60mm. In result, good atomization of liquid is obtained in widen flow rates. The mean droplet size is increased in orders of 4.7, 2.0. 9.5, $0.5\;{\mu}m$ surface roughness. Distilled water has a big mean droplet size than gasoline fuel in low flow rate. Above the 78cc/min flow rates, distilled water has a small mean droplet size than gasoline fuel. Liquid films changes are measured with ultrasonic power. Also, cavitation effect on sprays is observed.

• Journal of Institute of Control, Robotics and Systems
• /
• v.13 no.3
• /
• pp.218-223
• /
• 2007

The dissipation of high-power ultrasonic energy at the faces of the defect causes an increase in temperature. It is resulted from localized selective heating in the vicinity of cracks because of the friction effect. In this paper the measurement of size and direction of crack using UET(Ultrasound Excitation Thermography) is described. The ultrasonic pulse energy is injected into the sample in one side. The hot spot, which is a small area around the crack tip and heated up highly, is observed. The hot spot, which is estimated as the starting point of the crack, is seen in the nearest position from the ultrasonic excitation point. Another ultrasonic pulse energy is injected into the sample in the opposite side. The hot spot, the ending point of the crack, is seen in the closest distance from the injection point also. From the calculation of the coordinates of both the first hot spot and the second hot spot observed, the size and slope of the crack is estimated. In the experiment of STS fatigue crack specimen(thickness 14mm), the size and the direction of the crack was measured.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.49 no.11
• /
• pp.167-174
• /
• 2012

In this paper a ultrasonic oil level meter for measuring oil levels of vehicle transmissions is designed and its effectiveness is shown by experiments. On a FPGA(Field Programmable Gate Array) project IDE(Integrated Development Environment), all digital circuits for the meter is designed using a FPGA, which enables simplicity and high performance of the meter as well as short developing time. Also, power supplying circuit and analog circuits to process low voltage ultrasonic echo signal are designed and simulated. Under experiments, the designed level meter is verified to provide accuracy to within 1mm.

• 유체기계공업학회:학술대회논문집
• /
• 2005.12a
• /
• pp.287-294
• /
• 2005

Flow rate measurement uncertainties of the ultrasonic flow meter are generally influenced by many different factors, such as Reynolds number, flow distortion, turbulence intensity, wall surface roughness, velocity integration method along the acoustic paths, and transducer installation method, etc. Of these influencing factors, one of the most important uncertainties comes from the velocity integration method. In the present study, a optimization weighting factor method for 5-chord, which is given by a function of the chord locations of acoustic paths, is employed to obtain the mean velocity in the flow through a pipe. The power law profile is assumed to model the axi-symmetric pipe flow and its results are compared with the present weighting factor concept. For an asymmetric pipe flow, the Salami flow model is applied to obtain the velocity profiles. These theoretical methods are also compared with the previous Gaussian, Chebyshev, and Tailor methods. The results obtained show that for the fully developed turbulent pipe flows with surface roughness effects, the present weighting factor method is much less sensitive than Chebyshev and Tailor methods, leading to a better reliability in flow rate measurement using the ultrasonic flow meters.

• Journal of the Korean Ceramic Society
• /
• v.51 no.4
• /
• pp.243-247
• /
• 2014

Spherical NiO-YSZ particles were synthesized by ultrasonic spray pyrolysis (USP). The morphology of the synthesized particles can be modified by controlling parameters such as precursor pH, carrier-gas flow-rate, and temperature of the heating zone. The synthesized spherical NiO-YSZ particles have rough surface morphology at high carrier-gas flow-rates due to rapid gas exhaustion and insufficient particle ordering. The Ni-YSZ cermet anode synthesized by ultrasonic spray pyrolysis at a flow rate of l L/min, with precursor solution at pH4, showed a higher maximum power density of 256 $mW/cm^2$ compared to a conventionally mixed Ni-YSZ anode (185 $mW/cm^2$) at $800^{\circ}C$. While the area-specific resistance of conventionally mixed Ni-YSZ anodes increases gradually with operation time (indicating performance degradation), the Ni-YSZ anode synthesized by USP does not exhibit any performance degradation, even after 500 h.

• Journal of the Korean Society of Safety
• /
• v.33 no.6
• /
• pp.58-65
• /
• 2018

The life span of the porcelain insulator was made to be 30 years, but currently many of the 154kV NGK porcelain insulators using in Korea are found to have passed the production life. Accidents caused by aged mechanical breakdown can lead to disruption of power supply in some areas, large economic losses, and casualties. Therefore, ultrasonic method, which is one of the non - destructive test methods, is applied as a method for evaluating the integrity of porcelain insulators. In this study, the experiment on the interface of cap was conducted and the difference between the energy difference and the attenuation coefficient of the reflected wave was derived according to the interface state of the steel - cement. The results of this study are expected to be used as the basic data of the ultrasonic testing to evaluate the interface condition of the porcelain insulator cap.

• Corrosion Science and Technology
• /
• v.18 no.5
• /
• pp.196-205
• /
• 2019

Surface modification techniques are known to improve SCC by adding large compressive residual stresses to metal surfaces. This surface modification technology is attracting attention because it is an economical and practical technology compared to the maintenance method of existing nuclear power plants. Surface modification techniques include laser, water jet and ultrasonic peening, pinning and ultrasonic Nano-crystal surface modification (UNSM). The focus of this study was on the effect of ultrasonic amplitude in UNSM treatment on the corrosion properties of Alloy 600. A microstructure analysis was conducted using an optical microscope (OM), scanning electron microscope (SEM) and electron backscattering diffraction (EBSD). A cyclic polarization test and AC-impedance measurement were both used to analyze the corrosion properties. UNSM treatment influences the corrosion resistance of Alloy 600 depending on its amplitude. Below the critical amplitude value, the pitting corrosion properties are improved by grain refinement and compressive residual stress, but above the critical amplitude value, crevices are formed by the formation of overlapped waves. These crevices act as corrosion initiators, reducing pitting corrosion resistance.

• Nuclear Engineering and Technology
• /
• v.54 no.1
• /
• pp.186-192
• /
• 2022

Flow accelerated corrosion (FAC) is a type of pipe corrosion in which the pipe thickness decreases depending on the fluid flow conditions. In nuclear power plants, FAC mainly occurs in the carbon steel pipes of a secondary system. However, because the temperature of a secondary system pipe is over 150 ℃, in situ monitoring using a conventional ultrasonic non-destructive testing method is difficult. In our previous study, we developed a waveguide ultrasonic thickness measurement system. In this study, we applied a waveguide ultrasonic thickness measurement system to monitor the thinning of the pipe according to the change in pH. The Korea Atomic Energy Research Institute installed FAC-proof facilities, enabling the monitoring of internal fluid flow conditions, which were fixed for ~1000 h to analyze the effect of the pH. The measurement system operated without failure for ~3000 h and the pipe thickness was found to be reduced by ~10% at pH 9 compared to that at pH 7. The thickness of the pipe was measured using a microscope after the experiment, and the reliability of the system was confirmed with less than 1% error. This technology is expected to also be applicable to the thickness-reduction monitoring of other high-temperature materials.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2021.05a
• /
• pp.207-208
• /
• 2021

The non-destructive method using ultrasonic waves has been applied in many studies due to its low damage to the structure and its simple evaluation method and high precision. On the other hand, if the concrete is subjected to a high-temperature, the mechanical properties may be deteriorated due to the micro-crack network and the damage may be severe depending on the strength of the concrete. Therefore, this study attempts to evaluate the fundamental wave behavior of different strength ranges using the ultrasonic non-destructive method for concrete that has been subjected to high-temperature. As a result, the relative power of the fundamental wave was decreased as temperature increase. And it was confirmed that the 2nd and 3rd harmonics were generated at 110 MPa. However, to check the 2nd, 3rd harmonics 110 MPa or less, there is a need for further research considering the ultrasonic output, the output of the sender and receiver, and the appropriate frequency accordingly.