DOI QR코드

DOI QR Code

Analysis of pipe thickness reduction according to pH in FAC facility with In situ ultrasonic measurement real time monitoring

  • Oh, Se-Beom (Material Safety Technology Development Division, Korea Atomic Energy Research Institute) ;
  • Kim, Jongbeom (Material Safety Technology Development Division, Korea Atomic Energy Research Institute) ;
  • Lee, Jong-Yeon (Material Safety Technology Development Division, Korea Atomic Energy Research Institute) ;
  • Kim, Dong-Jin (Material Safety Technology Development Division, Korea Atomic Energy Research Institute) ;
  • Kim, Kyung-Mo (Material Safety Technology Development Division, Korea Atomic Energy Research Institute)
  • Received : 2021.04.05
  • Accepted : 2021.07.30
  • Published : 2022.01.25

Abstract

Flow accelerated corrosion (FAC) is a type of pipe corrosion in which the pipe thickness decreases depending on the fluid flow conditions. In nuclear power plants, FAC mainly occurs in the carbon steel pipes of a secondary system. However, because the temperature of a secondary system pipe is over 150 ℃, in situ monitoring using a conventional ultrasonic non-destructive testing method is difficult. In our previous study, we developed a waveguide ultrasonic thickness measurement system. In this study, we applied a waveguide ultrasonic thickness measurement system to monitor the thinning of the pipe according to the change in pH. The Korea Atomic Energy Research Institute installed FAC-proof facilities, enabling the monitoring of internal fluid flow conditions, which were fixed for ~1000 h to analyze the effect of the pH. The measurement system operated without failure for ~3000 h and the pipe thickness was found to be reduced by ~10% at pH 9 compared to that at pH 7. The thickness of the pipe was measured using a microscope after the experiment, and the reliability of the system was confirmed with less than 1% error. This technology is expected to also be applicable to the thickness-reduction monitoring of other high-temperature materials.

Keywords

Acknowledgement

This work was supported by a National Research Foundation of Korea (NRF) grant funded by the Korean government (2017M2A8A4015158).

References

  1. H. Keller, Erosionskorrosion an nassdampfturbinen, VGB-Kraftwerkste 54 (1974) 292-295.
  2. R.B. Dooley, V.K. Chexal, Int. J. Pres. Ves. Pip. 77 (2000) 85-90. https://doi.org/10.1016/S0308-0161(99)00087-3
  3. T. Sydberger, U. Lotz, J. Electrochem. Soc. 129 (1982) 276-283. https://doi.org/10.1149/1.2123812
  4. D.J. Kim, S.W. Kim, J.Y. Lee, K.M. Kim, S.B. Oh, G.G. Lee, J.B. Kim, S.S. Hwang, M.J. Choi, Y.S. Lim, S.H. Cho and H.P. Kim, Flow Accelerated Corrosion Assessment for SA106 Pipe with Elbow and Weld, NET (in press).
  5. R.B. Dooley, V.K. Chexal, Flow accelerated corrosion in pipe wall downstream of orifice for water and air-water bubble flows, Int. J. Pres. Ves. Pip. 77 (2000) 85-90. https://doi.org/10.1016/S0308-0161(99)00087-3
  6. B. Chexal, J. Horowitz, B. Dooley, P. Millett, C. Wood, R. Jones, M. Bouchacourt, F. Nordmann, P.S. Paul, W. Kastner, Flow-accelerated Corrosion, EPRI TR106611-R1, 1998.
  7. I.S. Woosey, Assessment and Avoidance of Erosion-Corrosion Damage in PWR Feed Pipe Work, Corrosion and Erosion Aspects of the Pressure Boundary Components of Light Water Reactors, IAEA, 1990.
  8. W. Kastner, K. Riedle, H. Tratz, Experimental inspections on material loss due to erosion-corrosion, VGB Kraftw. 64 (5) (1984) 411-423.
  9. G.G. Lee, E.H. Lee, S.W. Kim, D.J. Kim, Development of statistical modeling methodology for flow accelerated corrosion: effect of flow rate, water temperature, pH, and Cr content, KPV 12 (2) (2016) 40-49.
  10. Flow Accelerated Corrosion in Power Plants, EPRI Report, TR-106611-R1, Palo Alto, CA, 1998.
  11. D.J. Kim, H.C. Kwon, H.P. Kim, Corrosion Sci. 50 (2008) 1221. https://doi.org/10.1016/j.corsci.2008.01.008
  12. Y.H. Choi, S.C. Kang, Evaluation of piping integrity in thinned main feedwaterpipes, Nucl. Eng. Technol. 32 (2000) 67-76.
  13. A. Baba, C.T. Searfass, B.R. Tittermann, High temperature ultrasonic transducer up to 1000 C using lithium niobate single crystal, Appl. Phys. Lett. 97 (2010) 232901. https://doi.org/10.1063/1.3524192
  14. A. Megriche, L. Lebrun, M. Troccaz, Materials of Bi4Ti3O12 type for high temperature acoustic piezo-sensors, Sens. Actuators, A 78 (1999) 88-91. https://doi.org/10.1016/S0924-4247(99)00223-X
  15. P. Berge, J. Ducreux, P. Saint, Effects of chemistry on corrosion-erosion of steels in water and wet steam, Water Chemistry II, BN (1980) 19-23. Paper 2.
  16. Y.M. Cheong, K.M. Kim, D.J. Kim, High-temperature ultrasonic thickness monitoring for a pipe thinning in FAC proof test facility, Nuclear Eng. Technol. 49 (2017) 1463-1471. https://doi.org/10.1016/j.net.2017.05.002
  17. B. Chexal, J. Horowitz, B. Dooley, P. Millett, C. Wood, R. Jones, M. Bouchacourt, F. Nordmann, P.S. Paul, W. Kastner, EPRI TR-106611-R1, 1998. www.pdfsearch.asia.
  18. F.B. Celga, P. Cawley, J. Allin, J. Davies, High-temperature (>500 ℃) wall thickness monitoring using dry-coupled ultrasonic waveguide transducers, IEEE Trans. Ultrason. Ferroelectrics Freq. Contr. 58 (2011) 156-167. https://doi.org/10.1109/TUFFC.2011.1782
  19. Y.M. Cheong, J.H. Kim, J.H. Hong, H.K. Jeong, Measurement of dynamic elastic constants of RPV steel weld due to localized microstructural variation, J. Korean Soc. Non-Destruct. Test. 20 (2001) 559-564.
  20. S. B Oh, Y.M. Cheong, D.J. Kim, K.M. Kim, On-line monitoring of pipe wall thinning by a high temperature ultrasonic waveguide system at the flow accelerated corrosion proof facility 19 (2019) 1-10.
  21. W.Y. Maeng, B.S. Choi, J.W. Yeon, D.W. Kang, H.B. Lee, C.S. Wang, Handbook of Water Chemistry in Nuclear Power Plant, Donghwae, KAERI, 2009.
  22. V. Kain, Flow accelerated corrosion: Forms, mechanisms and case studies, Procedia Engineering 86 (2014) 576-588. https://doi.org/10.1016/j.proeng.2014.11.083
  23. T. Ohira, K. Fujiwara, F. Inada, K. Yoneda, D.H. Lister, A. Feicht, International Conference on FAC, 2010. Lyon, France.