• Transactions of Materials Processing
• /
• v.19 no.6
• /
• pp.363-371
• /
• 2010

In ultrasonic vibration drawing, the drawing forces can be reduced by applying ultrasonically oscillating dies. Ultrasonic vibration drawing has been considered as a means of accommodating high-level drawing processes such as shaped wire, ultrafine wire, and the wire drawing operation in semidry or dry condition. Prior studies were attempted to analyze the mechanism of improved drawing performances, such as reduced drawing force and improved lubrication characteristic. However, researches on design rule for ultrasonic vibration drawing system are not yet carried out. The principal objectives of this work are to design a set of tooling capable to superimpose the oscillations and to observe by experiments the influence of the ultrasonic oscillations on the wire drawing.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2015.05a
• /
• pp.224-225
• /
• 2015

Ultrasonic velocity method is applied to measure and correlate the strength of concrete to the velocity of the ultrasonic wave. With voids inside, mortar specimens may show the lower strength and it is intended to detect such change using the ultrasonic velocity method in this study. The amount of voids was varied and the measured data represented the condition of the mortar with voids. The test results can be used to predict the strength of concrete with voids using ultrasonic velocity method.

• Proceedings of the KSME Conference
• /
• 2004.04a
• /
• pp.25-30
• /
• 2004

In this paper, the compensation of interfacial scatter due to adhesive layer and adherend thickness ratio variation was applied to improve measuring precision by calculating ultrasonic attenuation coefficient in the Al/Epoxy dissimilar bonded components. The optimum condition of theoretical value and experimental measuring accuracy by the ultrasonic method in the Al/Epoxy dissimilar bonded components have been investigated. From the experimental results, we proposed a measurement method of the interfacial crack lengths by the ultrasonic attenuation coefficient and discussed it.

• Journal of the Korean Society for Railway
• /
• v.3 no.2
• /
• pp.77-83
• /
• 2000

This study proposes the integrity evaluation of the bogie frame using ultrasonic fractography analysis. Analysis objectives in this study are to investigate fracture planes of damaged zone by the A-scan method. The surface condition of fracture planes shows degree of degradation by the stress concentration. The detection of the natural defects in the bogie frame is performed using the characteristics of echodynamic pattern in ultrasonic signal. Results of ultrasonic testing agree fairly well with those of actual fracture plane. In quantitative fractography analysis, microstructures of actual fracture plane turned out to be intergranular and transgranular fracture. Proposed ultrasonic fractography analysis in this study can be used for the integrity evaluation of the bogie frame.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.27 no.6
• /
• pp.576-581
• /
• 2007

Ultrasonic nonlinearity has been considered as a promising method to evaluate the micro damage of material; however, its magnitude is so small that its measurement is not easy. Especially, when we use contact PZT transducer, if the contacting pressure is not kept in constant during the measurement then there exists extraneous fluctuation in the measured nonlinearity caused by the unstable contact condition, In this paper, we developed a pneumatic control system to keep the contacting pressure of transducer in constant during the measurement and analyzed the effect of contacting pressure to the ultrasonic nonlinearity measurement As a result, we found that the pressure of transducer in our measurement system should be greater than 170 kPa to measure the ultrasonic nonlinear parameter in stable with no dependency on the contacting pressure.

• Journal of the Korean Society of Hazard Mitigation
• /
• v.11 no.1
• /
• pp.101-105
• /
• 2011

Determination of ultrasonic frequency and experimental design approach to optimization of ultrasonic soil-washing process for remediation of diesel contaminated soil were investigated. Ultrasonic frequencies of 35, 72, and 100 kHz were used for determination of optimal frequency. $MINITAB^{(R)}$ program was used for experimental design of optimal washing condition. The optimal ultrasonic frequency was 35 kHz. Even though the number of cavitation bubble is little, however cavitation bubbles involving larger energy compared with high frequency was generated. Therefore, the removal efficiency at low frequency was higher than at high frequency. However the input energy has to be considered when the process is applied. The statistical tests from a factorial experiment shows that the application of ultrasound and mechanical mixing are the most important factor for design of an ultrasonic soil washing process. The lab-scale experiments are required to get the optimal condition of ultrasound and mechanical mixing for application of ultrasonic soil washing process.

• Korean Journal of Agricultural Science
• /
• v.46 no.1
• /
• pp.85-92
• /
• 2019

This study was intended to provide basic data for a health functional food study by exploring antioxidant activity of reflux extract according to the concentration of ethanol and the extract of ultrasonic waves extracted and reflux extracted under the same solvent conditions. In the same solvent condition, the reflux extract ($75.10{\pm}1.99mg$) showed a higher total phenol content than the ultrasonic wave extract ($51.74{\pm}2.28mg$). Flavonoids also had a higher reflux extract ($25.05{\pm}1.53mg$) than did ultrasonic extracts ($16.23{\pm}1.95mg$). Reflux extract according to ethanol concentration was found to have a higher phenol content than the 70% ethanol extract ($40.60{\pm}1.49mg$) in 60% ethanol extract. Flavonoid content was also similar to phenol content in reflux extract as determined by ethanol concentration from 60% ethanol ($25.05{\pm}1.53mg$) to 70% ethanol extract ($6.60{\pm}0.46mg$). In addition, the antioxidant activity (DPPH, TEAC, FRAP, ORAC) of the reflux extract in the same solvent conditions tended to be higher than that of ultrasonic extracts. Also, 60% ethanol extract had better antioxidant activity than 70% ethanol extract. However, an analysis of phenolic acid content through HPLC showed that the ultrasonic extract had a higher content in the same solvent condition than did the reflux extract. Not only the presence of phenolic acid, but also those of other compounds are believed to be attributed to the activity of antioxidants. Therefore, further studies are needed to clarify this phenomenon.

• 제어로봇시스템학회:학술대회논문집
• /
• 1991.10a
• /
• pp.1209-1213
• /
• 1991

This paper describes a new method for performance improvement ultrasonic ranging system using V40 controller. Detectable range of ultrasonic ranging system depends on transducer frequency and bandwidth of the receiver, and damping of the transducer, etc. Conventional ranging systems are somewhat inaccurate because they do not have capability of compensating changes in medium condition. The novel ranging system overcomes this disadvantage by placing in the same medium a dummy sensor functioning as a standard calibrating instrument and by providing data processing capability using V40 controller.

• Journal of Biosystems Engineering
• /
• v.21 no.2
• /
• pp.167-174
• /
• 1996

A Fuzzy Logic Controller(FLC) was developed for the autonomous operation of speedsprayer in an orchard. The autonomous operation with the FLC was graphically simulated under the real condition of the orchard. Image processing was used to find out the direction of running and four ultrasonic sensors were used to detect obstacles for the running. The simulation results showed that the speedsprayer could be operated autonomously with the FLC combined with the image processing and the ultrasonic sensors.

• Journal of Sensor Science and Technology
• /
• v.13 no.1
• /
• pp.66-71
• /
• 2004

Pt-doped zinc oxide (ZnO:Pt) films were deposited by ultrasonic spray pyrolysis. Resistivity variation with Pt concentration was measured. The Pt distribution in ZnO:Pt films was studied through Auger Electron Spectroscopy (AES). The ZnO:Pt films were annealed in the ambient of air, water vapor and ozone, respectively. The variation in crystallographic properties and surface morphologies with respect to the annealing condition was observed by X-Ray Diffraction (XRD) and Scanning Electron Microscopy (SEM). The resistivity variation of the films with the annealing condition was measured. Finally, Atomic Force Microscopy (AFM) measurements were carried out to study the effects of the annealing on the roughness of ZnO:Pt films.