• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.07a
• /
• pp.664-667
• /
• 2001

A flat-type L$_1$-B$_{8}$ Mode Ultrasonic motor(USM) uses longitudinal-bending multi-mode vibrator which is constructed with the metal-piezoceramic composite thin plate vibrator. Especially, the characteristics of vibrating displacement of the vibrator are important for the fabrication of USM. So, in this study, we tried to analyze them by the FEM(finite element method) simulation program. ANSYS 5.6 we used is a finite element software enabling the analysis of 2 or 3 dimensional structure of piezoelectric materials. Using this made us analyzing the resonance frequency and calculating displacement of vibrator and then the position of the projection.n.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07b
• /
• pp.674-677
• /
• 2002

In this paper, two kinds of windmill type motors which have a disk shape and a ring shape piezoelectric ceramics were studied. And characteristics of two models were compared with each others. A windmill type ultrasonic motor is composed of a stator, a rotor, and a ball bearing. The stator is made of a piezoelectric ceramics and two metals endcaps. When the piezoelectric ceramics vibrate, displacement of torsonal vibration appear at metal endcaps. The motor with 11.0[mm] diameter was studied by finite element analysis. The voltage of 100[V] was supplied at each model. Resonance frequency of 206.875[KHz] was obtained at the disk type, but ring type was 137.562[KHz]. The maximum torsonal displacement of $1.112[{\mu}m]$ was obtained at the disk type, but ring type was $1.698[{\mu}m]$.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07b
• /
• pp.634-637
• /
• 2002

Transducer for linear ultrasonic motor with symmetric and anti-symmetric modes was studied. The transducer was composed of two Langevin-type vibrators. In order to excite two vibration modes, Two Langevin-type vibrators must have 90-degree phase difference with each other. As result, tip of transducers moves in elliptical motion. In this paper, vibration shape of transducer was simulated and The resonant frequency and maximum displacement were calculated using the FEA (Finite Element Analysis).

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.11a
• /
• pp.219-220
• /
• 2006

In this study, m order to develop multilayer ceramics vibrator for ultrasonic nozzle, PMN-PNN-PZT ceramics were fabricated using $Li_2CO_3-Na_2CO_3$ as sintering aids and their piezoelectric and dielectric characteristics were investigated according to the aomunt of PbO. With increasing PbO contents. secondary phases were increased and phase structure were changed from tetragonal structure to rhombohedral structure and also electromechanical coupling factor were linearly decreased. At the composition ceramics with the sintering temperature of $870^{\circ}C$ and 1 mol% excess PbO, density, electromechanical coupling factor, dielectric constant, piezoelectric d constant and mechanical quality factor showed the optimum value of $7.879g/cm^2$, 0.55, 1149, 328pC/N, 1224, respectively for multilayer ceramics vibrator application for ultrasonic nozzle.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2000.11a
• /
• pp.930-933
• /
• 2000

In this report experimental ultrasonic machine system has been fabricated and experimental machining has been performed using glass as a workpiece material. As grit size increases, material removal rate(MRR) was observed to be increased at decreased applied tool pressure on the workpiece, however at the higher applied pressure above $2-4\;kg/cm^2$ for smaller grit size, the MRR was not increased. Also better surface roughness was obtained for smaller grit size. Microchipping was observed from the microscopic examination and the pattern is similar to the iso-stress field where cracking is considered to be initiated near the surface.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.19 no.1
• /
• pp.58-63
• /
• 2006

In this Paper, ZnO films mixed with iron oxide were prepared by an ultrasonic spray pyrolysis method. The chemical composition and structural properties as a function of the Fe atomic ratio in the deposition solution were studied. Zinc acetate and ferrous chloride were used as precursors of Zn and Fe, respectively. Fe atomic ratio to Zn varied from 0.15 to 10.0. Substrate temperature was fixed at $250^{\circ}C$. The crystallographic properties and surface morphologies of the films were studied by X-ray diffraction (XRD) and scanning electron microscopy (SEM), respectively. Electron probe X-ray microanalysis (EPMA) and X-ray photoelectron spectroscopy (XPS) were carried out to analyse the chemical composition and state of Zn and Fe atoms.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.15 no.10
• /
• pp.914-920
• /
• 2002

This study investigates the mechanism of a dual mode probe that generates both of the longitudinal and shear waves simultaneously with a single FZT element. Most of conventional ultrasonic probes are constructed to generate either longitudinal or shear waves. After poling, PZT has the hexagonal 6mm crystal symmetry. All possible crystal cuts are checked to determine appropriate Euler transformation angles for efficient excitation of dual modes. For the selected cut, performance of the dual mode element is analyzed through numerical simulation and experiments. Results of the analysis determine the optimal crystal cut for simultaneous generation of P and S waves of equal strength.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.11a
• /
• pp.195-198
• /
• 2004

ZnO films were Prepared by ultrasonic spray Pyrolysis on MgO substrates. The surface morphology and crystallinity were observed as a function of substrate temperature by SEM and XRD, respectively. PL properties of the ZnO films were studied by using Cd-He laser. UV light around 3.37 eV was pronounced in the PL spectra. The origin of the PL peak was discussed.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07b
• /
• pp.756-759
• /
• 2003

In this study, an ultrasonic transducer is fabricated with a 1-3 type composite resonator. Pulse-echo responses of an ultrasonic transducer are investigated in underwater with the designated water-levels. LED output signals of a level limit switch with changing a water level are obtained by using the currently developed self-made 1-3 type composite transducer and electric measuring unit. LED is turned on at above the up-limit level with increasing a water level, and LED is turned on at less than the down-limit level with decreasing a water level.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.26 no.3
• /
• pp.198-205
• /
• 2006

The necessity of nondestructively inspecting austenitic steels, fiber-reinforced composites, and other inherently anisotropic materials has stimulated considerable interest in developing beam models for anisotropic media. The properties of slowness surface playa key role in the beam models based on the paraxial approximation. In this paper, we apply a modular multi-Gaussian beam (MMGB) model to study the effects of material anisotropy on ultrasonic beam profile. It is shown that the anisotropic effects of beam skew and excess beam divergence enter into the MMGB model through parameters defining the slope and curvature of the slowness surface. The overall beam profile is found when the quasilongitudinal(qL) beam propagates in the symmetry plane of transversely isotropic austenitic steels. Simulation results are presented to illustrate the effects of these parameters on ultrasonic beam diffraction and beam skew. The MMGB calculations are also checked by comparing the anisotropy factor and beam skew angle with other analytical solutions.