• 토지주택연구
• /
• 제9권3호
• /
• pp.1-8
• /
• 2018

유럽과 미국에서는 말뚝기초 설계에 한계상태설계법 사용이 거의 정착되었으며, 세계적 추세에 따라 국내에서도 국토해양부가 한계상태설계법에 기반한 교량하부기초 설계기준을 제정하였지만, 국내 말뚝공법 및 지반조건에 대한 저항계수 연구가 부족하여 당장 설계에 반영하기에는 어려운 여건이었다. 이에 본 연구에서는 국내에서 많이 사용되고 있는 PHC 매입말뚝의 저항계수를 구하기 위하여 LH설계기준과 도로교설계기준 방법으로 산정한 지지력과 LH 현장에서 실시한 정재하시험(21회)과 동재하시험(EOID 21회, Restrike 21회) 결과를 신뢰성분석을 실시하였으며, 선행 논문(재하시험에 의한 PHC 매입말뚝의 저항계수 산정)에서 수행한 결과보다 2배 이상 많은 데이터를 추가하여 분석하였다. 그 결과 정재하지지력(극한)으로 구한 저항계수는 설계식 및 목표신뢰도지수에 따라 0.64~0.83, 동재하지지력(극한)으로 구한 저항계수는 0.42~0.55로 나와 정재하지지력(극한)으로 구한 저항계수보다 약 33% 작게 나타났다. 반면 수정동재하지지력(EOID의 극한선단지지력 + Restrike의 극한주면지지력)으로 구한 저항계수는 0.55~0.71로 나와 정재하지지력(극한)으로 구한 저항계수와 비교 시 그 차이가 약 14%로 줄어들었다. 데이터 추가에 의해 저항계수를 산정한 결과 이전 저항계수와 같거나 0.04정도 증가하여 데이터가 2배 이상 추가되어도 저항계수가 의미 있을 정도로 크게 변하지 않은 것으로 나타났다. 결론적으로 본 연구에서 정재하 및 동재하시험으로 산정한 전체 저항계수는 전반적으로 도로교설계기준(2015)에서 제시한 저항계수 0.3보다 커서 경제적인 설계가 가능한 것으로 나타났다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2010년도 춘계 학술발표회
• /
• pp.1286-1293
• /
• 2010

The ground anchor used in domestic area, which resists by adhesion between anchor body and the ground to the external force, seems not to be adequate for soft ground and urban area where the boundary between structures is close because the ground is disturbed and lost its strength during boring. In order to overcome such a shortcoming an expanded anchor system has been developed. The ground expansion is accomplished by means of Pulse Discharge Technology. In this technology, a high voltage of electricity is stored and discharged in milliseconds which induces high pressure acting on the ground. By making a couple of bulbs, a passive resistance as well as shaft resistance are mobilized, and therefore a higher pullout resistance comparing existing ground anchors is developed.In this study, a couple of full scale tests were conducted in order to figure out how much the resistance of an expanded anchor increases comparing to the straight. As a result, it was found that a remarkable increase in ultimate pullout capacity is observed for the soft ground and as the number of bulb increases. In addtion, as a result of applying to a cut slope reinforcement, it appeared that the length of fixed zone of anchor can be reduced effectively.

• 한국주조공학회지
• /
• 제13권4호
• /
• pp.333-341
• /
• 1993

The effects of alloying elements on the structure and mechanical properties of compacted/vermicular graphite cast irons containing copper, tin and molubdenum for producing pearlite matrix, and also containing phosphorus and boron for increasing wear resistance, were investigated. The Brinell hardness and ultimate tensile strength of the specimens with the range of compositions, [1.5% Cu-0.05% Sn-(0.2-0.4)% Mo-(0.2-0.6)% P-(0.035-0.070)% B], was found to fall within in the following range, depending on their composition; Brinell hardness of BHN 250-315, ultimate tensile strength of $28.1-40.3kg/mm^2$. It was also found within this experiment that CV graphite cast irons possessing higher amount of phosphide eutectic exhibit better wear resistance, but the wear resistance became deteriorate when the area fraction of phosphide eutectics exceed more than 10%. From these experimental results, it could be concluded that the CV graphite cast iron containing 1.5% Cu, 0.05% Sn, 0.4% Mo, 0.2% P and 0.035% B showed good mechanical and wear resistance properties.

• 한국지반공학회논문집
• /
• 제23권9호
• /
• pp.51-63
• /
• 2007

암반에 근입된 현장타설말뚝의 주면거동특성을 분석하고자, 편마암질의 풍화암/연암지역에서 현장 말뚝재하시험(압축재하 4회, 인발시험 5회)을 수행하였다. 이를 통해 암반 풍화, 굴착면 거칠기, 말뚝 직경, 재하방향 등의 요소들이 암반 근입 현장타설말뚝의 주면 전단거동을 결정짓는 주요요소임을 확인할 수 있었다. 본 연구에서는 국내에서 수행된 암반 근입 현장타설말뚝의 재하시험 사례를 토대로 국내 암반조건을 반영한 극한주면마찰력($f_{max}$)을 제안하였다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2009년도 세계 도시지반공학 심포지엄
• /
• pp.1354-1359
• /
• 2009

Ground anchor should not be used in soft clay, because anchor resistance can not be guaranteed. However, there is a way to increase the capacity of anchors. The anchor is an underreamed anchor by using high voltage electric discharge energy. In this study, a series of field test were carried out in order to find ultimate load of underreamed anchors in weathered soil at the new apartment construction site located in Inchon, Korea. Data were analyzed in order to define a relation between ultimate load and the number of electric discharge.

• Steel and Composite Structures
• /
• 제38권5호
• /
• pp.599-615
• /
• 2021

The ultimate strength behaviour of sandwich composite beams with J-hooks and normal weight concrete (SCSSBJNs) are studied through two-point loading tests on ten full-scale SCSSBJNs. The test results show that the SCSSBJN with different parameters under two-point loads exhibits three types of failure modes, i.e., flexure, shear, and combined shear and flexure mode. SCSSBJN failed in different failure modes exhibits different load-deflection behaviours, and the main difference of these three types of behaviours exist in their last working stages. The influences of thickness of steel faceplate, shear span ratio, concrete core strength, and spacing of J-hooks on structural behaviours of SCSSBJN are discussed and analysed. These test results show that the failure mode of SCSSBJN was sensitive to the thickness of steel faceplate, shear span ratio, and concrete core strength. Theoretical models are developed to estimate the cracking, yielding, and ultimate bending resistance of SCSSBJN as well as its transverse cross-sectional shear resistance. The validations of predictions by these theoretical models proved that they are capable of estimating strengths of novel SCSSBJNs.

• 토지주택연구
• /
• 제7권4호
• /
• pp.281-289
• /
• 2016

압축 부재인 PHC 말뚝(직경 600mm)도 강선의 부착력을 높이면 83.6~91.6tonf의 극한 인장력에 대해 구조적으로 저항할 수 있는 것으로 실험결과 나타났다. 이러한 시험결과에 안전율을 고려하여 적절한 허용값을 제시하면 부상방지 앵커를 대체하거나 절감시킬 수 있는 것으로 기대되었다. 이를 위해서는 구조적 인장성능과 함께 실제 지반에 시공된 매입말뚝의 인발저항 거동이 규명되어야 한다. 본 연구에서는 현장에 시공된 실제 매입말뚝의 인발거동 특성을 파악하기 위하여 정적 인발재하시험을 실시하여 주면마찰력 산정식과 비교하였다. 또한, 간편하게 인발저항력을 평가하기 위하여 PDA를 이용한 동재하시험을 실시하여 정적 인발재하시험 결과와 비교하였다. 그 결과, 매입말뚝의 시멘트풀이 충분히 경화한 후인 15일 후에는 LH 주면마찰력 산정식의 마찰력과 정적인발재하시험결과가 잘 일치하였고 동재하시험에서 구한 마찰력과도 비교적 잘 일치하는 것으로 나타났다.

• Structural Engineering and Mechanics
• /
• 제21권2호
• /
• pp.221-235
• /
• 2005

In this paper, the shear resistance behaviour of reinforced concrete (RC) dapped end beams is investigated by 24 tests until failure load. The main parameters considered are the dapped end height, the type and effective range to provided the stirrups and the bent form of the longitudinal reinforcement. The failure behaviour of dapped end beams is presented and some conclusions are given. Inclined stirrups and longitudinal bent reinforcement have more influence on the shear capacity than vertical stirrups. Additionally, the shear mechanism of dapped end beams is analysed. Relatively simple semi-empirical equations for shear strength have been derived based on the results of 22 dapped end beams. The predicted results are in close agreement with the experimental ones. Finally, some design suggestions for the ultimate shear strength of dapped end beams are presented.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2006년도 춘계학술발표회 논문집(I)
• /
• pp.50-53
• /
• 2006

An experimental investigation on the behavior of reinforced concrete coupling beams is presented. The test variables are the span-to-depth ratio, the ratio of flexural reinforcement and the ratio of shear rebar. The distribution of arch action and truss action which compose the mechanism of shear resistance is discussed. This study proposes the deformation model for reinforced concrete coupling beams considering the bond slip of flexural reinforcement. The yielding of flexural reinforcements determines yielding states and the ultimate states of reinforced concrete coupling beam are defined as the ultimate compressive strain of struts and the degradation of compressive strength due to principal tensile strain of struts. It is expected that this model can be applied to displacement-based design methods.

• 한국지진공학회:학술대회논문집
• /
• 한국지진공학회 2006년도 학술발표회 논문집
• /
• pp.233-240
• /
• 2006

An experimental investigation on the behavior of reinforced concrete coupling beams is presented. The test variables are the span-to-depth ratio, the ratio of flexural reinforcement and the ratio of shear rebar. The distribution of arch action and truss action which compose the mechanism of shear resistance is discussed. This study proposes the deformation model for reinforced concrete coupling beams considering the bond slip of flexural reinforcement. The yielding of flexural reinforcements determines yielding states and the ultimate states of reinforced concrete coupling beam are defined as the ultimate compressive strain of struts and the degradation of compressive strength due to principal tensile strain of struts. It is expected that this model can be applied to displacement-based design methods.