• 한국진공학회지
• /
• 제13권1호
• /
• pp.39-45
• /
• 2004

UV-나노임프린팅 (Ultraviolet-Nanoimprinting Lithography:UV-NIL) 공정 기술은 수십 나노에서 수 나노미터 크기의 구조물을 적은 비용으로 대량생산 할 수 있다는 장점을 가지고 있는 기술로 최근 전세계적으로 연구가 활발히 진행되고 있다. 본 연구에서는 반도체 공정 중 마스크 제작 공정을 이용하여 나노패턴을 가진 5${\times}$5${\times}$0.09 인치 크기의 수정스탬프(quartz stamp)를 제작하였고, 임프린팅 (imprinting)시에 레지스트(resist)와 스탬프(stamp) 사이에서 발생하는 점착현상(adhesion)을 방지하고자 그 표면에 Fluoroalkanesilane(FAS) 표면처리를 하였다. 웨이퍼의 평탄도를 개선하고 친수(hydrophilic) 상태의 표면을 만들기 위해 그 표면에 평탄화층을 스핀코팅하였고, 1 nl의 분해능을 가진 디스펜서(dispenser)를 이용하여 레지스트 액적을 도포하였다. 스템프 상의 패턴과 레지스트에 임프린트된 패턴은 SEM, AFM 등을 이용하여 측정하였으며, EVG620-NIL 장비를 이용한 임프린팅 실험에서 370 nm - 1 um 크기의 다양한 패턴을 가진 스탬프의 패턴들이 정확하게 레지스트에 전사됨을 확인하였다.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2008년도 추계학술발표대회 및 제15회 신소재 심포지엄
• /
• pp.21.1-21.1
• /
• 2008

• 반도체디스플레이기술학회지
• /
• 제10권4호
• /
• pp.53-59
• /
• 2011

Recently there have been considerable attentions on nanoimprint lithography (NIL) by the display device and semiconductor industry due to its potential abilities that enable cost-effective and high-throughput nanofabrication. Although one of the current major research trends of NIL is large-area patterning, the technical difficulties to keep the uniformity of the residual layer become severer as the imprinting area increases more and more. In this paper we focused on the deformation of the $2^{nd}$ generation TFT-LCD sized ($370{\times}470mm^2$) large-area soft mold in the UV imprinting process. A mold was fabricated with PDMS(Poly-dimethyl Siloxane) layered glass back plate(t0.5). Besides, the mold includes large surrounding wall type protrusions of 1.9 mm width and the via-hole(7 ${\mu}m$ diameter) patterend area. The large surrounding wall type protrusions cause the proximity effect which severely degrades the uniformity of residual layer in the via-hole patterend area. Therefore the deformation of the mold was calculated by finite element analysis to assess the effect of large surrounding wall type protrusions and the flexiblity of the mold. The deformation of soft mold was verified by the measurements qualitatively.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회A
• /
• pp.1934-1938
• /
• 2008

Formation of air bubble is the one of common defects in UV nano imprint lithography. Location of dispensing and volume of droplets are among the most important parameters in the process. ]n this study, UV curable resin droplets with different volumes were dispensed at different locations and pressed to investigate air bubble formation. By varying volume of droplet and dispensing location, process conditions were found for minimum air bubble area.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2010년도 춘계학술대회 논문집
• /
• pp.635-636
• /
• 2010

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2010년도 춘계학술대회 논문집
• /
• pp.525-526
• /
• 2010

• 한국기계가공학회지
• /
• 제16권1호
• /
• pp.96-101
• /
• 2017

We have developed a compact desktop-sized nanopatterning system driven by the Roll-to-Roll (R2R) nanoimprinting (NIL) principle. The system realizes the continuous and high-speed stamping of various nanoscale patterns on a large-area flexible substrate without resorting to ponderous and complicated instruments. We first lay out the process principle based on continuous NIL on a UV-curable resin layer using a flexible nanopatterned mold. We then create conceptual and specific designs for the system by focusing on two key processes, imprinting and UV curing, which are performed in a continuous R2R fashion. We build a system with essential components and optimized modules for imprinting, UV curing, and R2R conveying to enable simple but effective nanopatterning within the desktop volume. Finally, we demonstrate several nanopatterning results such as nanolines and nanodots, which are obtained by operating the built desktop R2R NIL system on transparent and flexible substrates. Our system may be further utilized in the scalable fabrication of diverse flexible nanopatterns for many functional applications in optics, photonics, sensors, and energy harvesters.

• 한국기계가공학회지
• /
• 제10권4호
• /
• pp.76-81
• /
• 2011

UV imprinting process can manufacture high-functional optical components with low cost. If hard polymers can be used as transparent molds at this process, the cost will be much lower. However, there are limited researches to predict the machinability and the burr of hard polymers. Therefore, a new method to predict them by analyzing load-depth curves which can be obtained by the instrumented indentation test was developed in this study. The load-depth curve contains elastic deformation and plastic deformation simultaneously. The ratio of the plastic deformation over the sum of the two deformation is proportional to the ductility of materials which is one of the parameters of the machinability and the burr. The instrumented indentation tests were performed on the transparent molds of the hard polymers and the values of ratio were calculated. The machinability and the burr of three kinds of hard polymers were predicted by the ratio, and the prediction was in agreement with the experimental results from the machined surfaces of the three kinds of hard polymers.

• 한국생산제조학회지
• /
• 제18권6호
• /
• pp.697-701
• /
• 2009

A simple method for the fabrication of porous nano-master for the anti-reflection effect on the transparent substrates is presented. In the conventional fabrication methods for antireflective surface, coating method using materials with low refractive index has usually been used. However, it is required to have a high cost and long processing time for mass production. In this paper, we developed a porous nano-master with anti-reflective surface for the molding stamper of the injection mold, hot embossing and UV imprinting by using the aluminum anodizing process. Through two-step anodizing and etching processes, a porous nano-master with anti-reflective surface was fabricated at the large area. Pattern size Pore diameter and inter-pore distance are about 130nm and 200nm, respectively. In order to replicate anti-reflective structure, hot embossing process was performed by varying the processing parameters such as temperature, pressure and embossing time etc. Finally, antireflective surface can be successfully obtained after etching process to remove selectively silicon layer of AAO master.

• 한국재료학회지
• /
• 제16권4호
• /
• pp.225-230
• /
• 2006

Nanoimprint lithography (NIL) is a novel method of fabricating nanometer scale patterns. It is a simple process with low cost, high throughput and resolution. NIL creates patterns by mechanical deformation of an imprint resist and physical contact process. The imprint resist is typically a monomer or polymer formulation that is cured by heat or UV light during the imprinting process. Stiction between the resist and the stamp is resulted from this physical contact process. Stiction issue is more important in the stamps including narrow pattern size and wide area. Therefore, the antistiction layer coating is very effective to prevent this problem and ensure successful NIL. In this paper, an antistiction layer was deposited and characterized by PECVD (plasma enhanced chemical vapor deposition) method for metal stamps. Deposition rates of an antistiction layer on Si and Ni substrates were in proportion to deposited time and 3.4 nm/min and 2.5 nm/min, respectively. A 50 nm thick antistiction layer showed 90% relative transmittance at 365 nm wavelength. Contact angle result showed good hydrophobicity over 105 degree. $CF_2$ and $CF_3$ peaks were founded in ATR-FTIR analysis. The thicknesses and the contact angle of a 50 nm thick antistiction film were slightly changed during chemical resistance test using acetone and sulfuric acid. To evaluate the deposited antistiction layer, a 50 nm thick film was coated on a stainless steel stamp made by wet etching process. A PMMA substrate was successfully imprinting without pattern degradations by the stainless steel stamp with an antistiction layer. The test result shows that antistiction layer coating is very effective for NIL.