• The Journal of the Korea Contents Association
• /
• v.6 no.3
• /
• pp.38-45
• /
• 2006

A dual-level low voltage differential signalling (DLVDS) circuit is proposed aiming at reducing transmission lines for a LCD driver IC. We apply two data to the proposed DLVDS circuit as inputs. Then, the transmitter converts two inputs to two kinds of fully differential signals. In this circuit, two transmission lines are sufficient to transfer two inputs while keeping the LVDS feature. However, the circuit has a common mode bias fluctuation due to difference of the input bias and the reference bias. We compensate the common mode bias fluctuation using a feedback circuit of the current source bias. The receiver recovers the original input data through a level decoding circuit. We fabricated the proposed circuit using $0.25{\mu}m$ CMOS technology. The simulation results of proposed circuit shows 1-Gbps/2-line data rate and 35mW power consumption at 2.5V supply voltage, respectively.

• Proceedings of the KIEE Conference
• /
• 2002.04a
• /
• pp.183-185
• /
• 2002

This paper proposes the test method for the testing of a RLC parallel circuit on the electronic circuit board. This method utilizes a guarding circuit and a phase detection circuit. The guarding circuit separates electrically the tested device or circuit from printed circuit board. Phase detector estimates the phase difference from two signals, voltage and current. This method computes R. L and C value from phase difference($\theta$) and impedance value(Z) obtained by enforcing two other frequence stimulus under the guarding state.

• Journal of the Semiconductor & Display Technology
• /
• v.20 no.4
• /
• pp.108-113
• /
• 2021

In this paper, a totem pole PFC was structured in two methods with FET and diode for low-speed switch while GaN FET was used for high-speed switch. Internal power loss, power conversion efficiency and steady-state characteristics of the two methods were compared in the totem pole bridgeless PFC circuit which is widely applied in large-capacity and high-efficiency switching rectifier of 500W or more. In order to compare and confirm the steady-state characteristics under equal conditions, a 2kW class totem pole bridgeless PFC was constructed and the experimental results were analyzed. From the experimental results, it was confirmed that the low-speed switch operation has a large difference in efficiency due to the internal conduction loss of the low-speed switch at a low input voltage. Especially, input power factor and load characteristic showed no difference regardless of the low-speed switch operation.

• The Journal of the Acoustical Society of Korea
• /
• v.32 no.4
• /
• pp.361-368
• /
• 2013

As one way to describe the behavior of a vibrating string, analogies to a transmission line have been made based on the fact that they have oppositely travelling waves on each of them. In such analogies, a rigid end to the string has been represented as an open circuit, and the displacement of the string as the current on the transmission line. However it turns out that the rigid end corresponds to a short circuit, the displacement to the voltage by the theory of the transmission line, and it is confirmed by experiments with circuit simulations. Based on these discoveries, a transmission line based plucked string model comprising a transmission line, two piecewise linear current sources, and switches is proposed. The proposed model is validated by showing that the voltage at the arbitrarily chosen location, and the voltage calculated over an infinitesimal portion at the end of the transmission line are consistent with the displacement at the corresponding location and the force on the rigid end of the string from the well known difference form of a wave equation governing the behavior of the string with its fundamental frequency tuned to that for the proposed model, respectively. Moreover, the applicability of the proposed model to modeling string and wind instruments is presented.

• Journal of the Institute of Convergence Signal Processing
• /
• v.13 no.4
• /
• pp.201-206
• /
• 2012

The indirect-contact ECG measurement is a newly developed method for unconstrained and nonconscious measurement in daily life. This study introduced a new method of electrode circuit design developed for reducing the 60Hz power line noise observed at the indirect-contact ECG measurement. By the introduced common-mode-driven shielding, the voltage of the electrical shield surrounding the capacitive coupling electrode is maintained at the same as the common mode voltage. Though the method cannot reduce the level of common mode voltage itself, that reduces effectively the differential mode noise converted from the common mode voltage by the difference of cloth impedance between the two capacitive coupling electrode. The experiment results using the actual indirect-contact ECG showed that the 60Hz power line noise was reduced remarkably though the reduction ratio was smaller than the expected by the theory. Especially, the reduction ratio became large for the large difference of cloth. It is expected that the introduced method is useful for reducing the power line noise under condition of poor electrical grounding.

• Journal of the Korean Society for Precision Engineering
• /
• v.33 no.3
• /
• pp.217-223
• /
• 2016

In this paper, the movement of a liquid metal droplet in a channel by continuous electrowetting effect is analyzed. The channel is fabricated using two glass substrates and silicone rubber as spacers, and a mercury droplet and dilute sulfuric acid are added into the channel. The droplet is moved according to voltage applied at both ends of the channel through an electrolyte. According to the shape of the droplet and the applied voltage, the velocity of the droplet is changed. The velocity is proportional to the applied voltage and inversely proportional to the length of the droplet, both theoretically and experimentally. Contact angle hysteresis and a meniscus change were also found in the moving state. This implies the existence of a threshold in movement by Laplace pressure difference. The experiment indicated that the sliding angle was inversely proportional to the width of the droplet but that the voltage threshold was proportional to the width.

• Proceedings of the KIEE Conference
• /
• 1994.07a
• /
• pp.183-185
• /
• 1994

A new method for determination of electric parameter of cell membranes is proposed. Two circular electrodes is designed to have repulsive force. From the potential energy analysis, stable points where a cell is levitated between electrodes exist and move as frequency or voltage change. The levitated cell in the stable point fall freely when DEP force is zero. The DEP force is dependent on the frequency and the force is zero at the critical frequency. The critical frequency is determined by measuring the difference between the time taken at zero-applied voltage and the time taken at the frequency and the voltage. For example, the critical frequency and stable points of N.crassa slime cell is numerically evaluated. In the exeriment, polystyrene in water is levitated at the stable point. We show that the stable point move as the applied voltage is changed.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.21 no.4
• /
• pp.789-794
• /
• 2017

Subthreshold current model is presented using analytical potential distribution of junctionless cylindrical surrounding-gate (CSG) MOSFET and threshold voltage shift is analyzed by this model. Junctionless CSG MOSFET is significantly outstanding for controllability of gate to carrier flow due to channel surrounded by gate. Poisson's equation is solved using parabolic potential distribution, and subthreshold current model is suggested by center potential distribution derived. Threshold voltage is defined as gate voltage corresponding to subthreshold current of $0.1{\mu}A$, and compared with result of two dimensional simulation. Since results between this model and 2D simulation are good agreement, threshold voltage shift is investigated for channel dimension and doping concentration of junctionless CSG MOSFET. As a result, threshold voltage shift increases for large channel radius and oxide thickness. It is resultingly shown that threshold voltage increases for the large difference of doping concentrations between source/drain and channel.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.17 no.6
• /
• pp.486-494
• /
• 2012

In this paper, we proposes the three-phase embedded Z-source inverter consisting of the three embedded Z-source converters and it's the output voltage control method. Each embedded Z-source converter can produce the bipolar output capacitor voltages according to duty ratio D such as single-phase PWM inverter. The output AC voltage of the proposed system is obtained as the difference in the output capacitor voltages of each converter, and the L-C output filter is not required. Because the output AC voltage can be stepped up and down, the boost DC converter in the conventional two-stage inverter is unnecessary. To confirm the validity of the proposed system, PSIM simulation and a DSP based experiment were performed under the condition of the input DC voltage 38V, load $100{\Omega}$, and switching frequency 30kHz. Each converter is connected by Y-connection for three-phase loads. In case that the output phase voltage is the same $38V_{peak}$ as the input DC voltage and is the 1.5 times($57V_{peak}$), the simulation and experimental results ; capacitor voltages, output phase voltages, output line voltages, inductor currents, and switch voltages were verified and discussed.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.7 no.4
• /
• pp.287-298
• /
• 2007

A two-dimensional treatment of the potential distribution under the depletion approximation is presented for poly-crystalline silicon thin film transistors. Green's function approach is adopted to solve the two-dimensional Poisson's equation. The solution for the potential distribution is derived using Neumann's boundary condition at the silicon-silicon di-oxide interface. The developed model gives insight into device behavior due to the effects of traps and grain-boundaries. Also short-channel effects and drain induced barrier lowering effects are incorporated in the model. The potential distribution and electric field variation with various device parameters is shown. An analysis of threshold voltage is also presented. The results obtained show good agreement with simulated results and numerical modeling based on the finite difference method, thus demonstrating the validity of our model.