• Journal of the Korean Electrochemical Society
• /
• v.10 no.1
• /
• pp.25-30
• /
• 2007

Proton exchange membrane fuel cell(PEMFC) performance could be affected by various factors such as cell temperature, total pressure, partial pressure of reactants and relative humidity. Hydrogen ion is combined with water to form hydronium ion [$H_3O^+$] and pass through membrane resulting electricity generation. Cooling system is needed to remove heat and other uses on large scale fuel cell. In case that collant conductivity is increased, fuel cell performance could be decreased because produced electricity could be leaked through coolant. In this study, triple distilled water(TDW) and antifreeze solution containing ethylene glycol was used to observe resistance change. Resistance of TDW was taken 28 days to reach preset value, and effect on fuel cell operation was not observed. Resistance of antifreeze solution was not reached to preset value up to 48 days, but performance failure occurred presumably caused by bipolar plate junction resulting stoppage resistance experiment. Generally PEMFC humidification is performed near-saturated operating conditions at various temperatures and pressures, but non-humidifying condition could be applied in small scale fuel cell to improve efficiency and reduce system cost. However, it was difficult to operate large scale fuel cell without humidifying, especially higher than $50{\sim}60^{\circ}C$. In case of small flux such as 0.78 L/min, temperature difference between inlet and outlet was occurred larger than other cases resulting performance decrease. Non-humidifying performance experiments were done at various cell temperature. When both of anode and cathode humidification were removed, cell performance was strongly depended on cell operating temperature.

• Applied Biological Chemistry
• /
• v.20 no.1
• /
• pp.88-94
• /
• 1977

A laboratory study was made of liming on the extractability of phosphate added to the uncultivated acid soils differing in clay content. The experiments were conducted with different rates of calcium carbonate and triple superphosphate at field capacity and 50% field capacity. The concentration of extractable phosphate was greatly reduced by simultaneous addition of calcium carbonate in the loam soil. When samples of the loam soil were preincubated for ranging from 0 to 50 days in the presence of calcium carbonate prior to phosphate application, the extractable phosphate concentration increased with preincubation time, and more phosphate was extracted from the soil maintained at 50% field capacity during the incubation. However, the extractable phosphate concentration in the sandyloam soil did not change with preincubation time and was not affected by moisture status. It may be concluded that the extractability of added phosphate was influenced by not only liming time but physical properties of soil.

• Journal of Sasang Constitutional Medicine
• /
• v.7 no.2
• /
• pp.59-88
• /
• 1995

Three groups have participated in this study. 1) The first group consists of 57 patients were who had been treated in the Oriental Medical Hospital at Kyung Hee Medical Center. 2) The second group consists of 37 outpatients who had been treated in the Oriental Medical Hospital at Kyung Hee Medical Center. 3) The third group consists of 76 students of the Oriental Medical School at Kyung Hee University. The following conclusions were made in comparison with EAV measurement values, SaSang Constitution Classfication and CVA. 1. The following conclusions were made in comparison with EAV measurement values and Type(SaSang Constitution Classfication). 1) The analsis of the Correlation in Normal group with EAV measurement values and Type(SaSang Constitution Classfication). 2) The analysis of the correlation in patient group with EAV measurement values showed significant differences in Right meridians(Nerval degeneration vessel, Circulation, Allergy) and in Left meridian(Liver). 3) The analysis of the correlation in Total(Normal+patient)group with EAV measurement values showed significant differences in Right meridians(Large intestine, Nerval degeneration vessel, Circulation, Allergy, Pancreas) and in Left meridians(Lymph vessel, Nerval degeneration vessel, Spleen, liver). 4) The above results showed common-significant differences in Right Allery meridian and in Left Liver meridian. 2. The analysis of the correlation in EAV measurement values and Group (Cerebrovascular accident) showed significant differences in Right meridians(Lymph vessel, Lung, Nerval degeneration vessel, Allergy, Paren & Epith. degeneration vessel, Triple warmer, Heart, Pancreas, Stomach, Fibroid degeneration vessel, Skin, Fatty degeneration vessel, Heart, Stomach, Fibroid degeneration vessel, Skin, Fatty degeneration vessel, Bile duct, Kidney). 3. The analysis of the correlation in EAV measurement values and Para(GROUPS according to PARALYSIS)showed significant differences in Left Stomatch meridian. The analysis of the correlation in EAV measurement values and Para(GROUPS according to PARALYSIS) about the differance of right measurement values and left measurement values showed significant differences in Nerval degeneration vessel, Stomatch, Gall bladder & Bile duct, Kidney and Urinary Bladder meridians. 4. The analysis of the correlation in EAV measurement values and Compl(GROUPS according to COMPLICATION with CVA)showed significant differences in Right meridians(Lymph vessel, Articular degeneration vessel, Fatty degeneration vessel) and in Left meridians(Lung, Stomatch, Fatty degeneration vessel). 5. The analysis of the correlation in Type and MORPHOROGICAL DIAGRAMING (HTOUPS according to MORPHOROGY) showed significant differences in Cranium region, Chest region, Stomatch region and Umbilicum region. 6. The analysis of the correlation in BAZ measurement values and Group(Cerebral Vascular Attack)showed significant differences, the analysis on the correlation of BAZ measurement values and Type(SaSang Constitution Classfication) didn't show any significant differences. 7. In comparison with Actual measurement vales and Voll's measurement values, BAZ measurement values agree with Voll's measurement values but CMP measurement values lower than the Voll's measurement values. Later We have to research further about classifications of race, age, sex etc. The EAV measurement values have Group(Cerebrovascular accident) more correlative than Type(SaSang Constitution Classfication). The EAV may well be that it will be used as an accessory method in SaSang Constitution Classfication and as a diagnostic method in medicine too.

• Korean Journal of Microbiology
• /
• v.46 no.3
• /
• pp.233-239
• /
• 2010

Four genes (yqfR, yfmL, ydbR, deaD) were identified as putative DEAD-box RNA helicase genes in the genomic sequence of Bacillus subtilis by homology search. To understand the function of these genes, each of the genes was deleted and the constructed strains were tested for their growth charateristics at different temperatures. The growth rate of ydbR deletion mutant ($T_d$=53 min) was a little bit reduced at $37^{\circ}C$ as compared to that of wild type strain (CU1065). But the growth rate of other three (yqfR, yfmL, deaD) deletion mutants ($T_d$=30-40 min) is nearly equal to the growth rate of wild type ($T_d$=32 min). On the other hands, the growth rate of deletion mutants were reduced at $22^{\circ}C$ in order of yqfR ($T_d$=151 min), yfmL ($T_d$=214 min), ydbR ($T_d$=343 min), which showed cold-sensitive phenotype. The deletion mutant of deaD ($T_d$=109 min) grew equally as compared to the growth rate ($T_d$=102 min) of the wild type at $22^{\circ}C$ and did not show cold-sensitive growth. Double, triple and quadruple deletion mutants of these genes were constructed, and growth rate of these mutants were measured at various temperature conditions ($22^{\circ}C$, $37^{\circ}C$, $42^{\circ}C$) using LB broth. Multiple deletion mutations showed more severe cold-sensitive growth than single deletion mutations, and double deletion of ydbR and yfmL ($T_d$=984 min) showed most cold-sensitive growth than any other double mutants. Such a cold-sensitive growth of these mutations is quite similar to the result of csdA or srmB deletion in E. coli and suggested that physiological role of ydbR and yfmL is related with ribosome assembly.

• Korean Journal of Acupuncture
• /
• v.24 no.1
• /
• pp.65-77
• /
• 2007

목 적 : 본 연구(硏究)는 수소양삼초경근(手少陽三焦頸筋)의 이론적(理綸的) 근거(根據)를 해부학적(解剖學的)으로 제공(提供)하고 임상(臨床)에 경근(經筋)의 정확(正確)한 적용(適用)을 위함이다. 방 법 : Cadaver에 경근(經筋)을 표시(表示)하고 각각(各各)의경 경혈부위(經穴部位)에 표식(標識)와 pore 작업을 수행하고 각 경혈부(經穴部)를 피부(皮膚), 근막(筋膜), 그리고 근육(筋肉)의 천층(淺層), 중문층(中問層), 그리고 심층부(深層部)를 순서적(順序的)으로 해부(解剖)하여 근육(筋肉), 신경(神經), 혈관(血管) 등을 관찰(觀察)한다. 결 과 및 결 론 : 수소양삼초경근(手少陽三焦經筋)의 해부학적(解剖學的) 고찰(考察) 결과(結果)는 다음과 같다. 1) 근(筋) 육(肉) : 천층에 근막(TE1), 근막확장대(TE2), 근막과 근간결합(TE3), 근막과 신근지대(TE4), 근막과총지신근건(TE5), 근막및 총지신근과 소지신근간(TE6), 근막과 소지신근(TE7), 총지신근(TE8), 척측수근신근과 소지신근간(TE9), 상완삼두근건(TE10, 11), 상완삼두근(TE12), 삼각근(TE13), 삼각근및 극하근과 극상근간(TE14). 승모근(TE15), 흉쇄유돌근(TE-16, 17, 18), 후이개근(TE19, 22), 상이개근(TE20), 전이개근및 이하선근막(TE21), 안륜근(TE23), 중층에 소지신근건과 총지신근건간(TE4), 측두근막과 측두근(TE2O, 22, 23), 심층에 배측골간근(TE3), 시지신근과 골간막(TE5) 장모지신근(TE6), 시지신근(TE7), 장지신근과 장모지외전근간(TE8, 9), 상완삼두근(TE13), 견갑거근(TE15), 두판상근(TE16), 경상설골근과 하악이복근간(TE17) , 이복근(TE18) .2) 신(神) 경(經) : 천층에 척골신경의 배측지(TE1, 2, 3), 후전완피신경(TE4, 5, 6, 8, 9, 10, 11), 내측전완피신경(TE5, 6, 7, 8, 9, 10, 11), 후상완피신경(TE12, 13), 상외측상완피신경(TE13), 외측쇄골상신경(TE14, 15),대이개신경(TE16, 17, 18, 19), 소후두신경(TE19, 20), 이개측두신경(TE20, 21, 22), 안면신경측두지(TE22, 23), 관골측두신경(TE23), 중층에 견갑상신경(TE15), 견갑배신경(TE15), 경상설골근신경(TE17), 후이개신경(TE18, 19, 20), 안면신경측두지(TE20, 21, 22), 심층에 후골간신경(TE5, 6, 7), 요골신경심지(TE8, 9, 12, 13), 견갑상신경(TE14), 액와신경가지(TE14), 부신경(TE16), 안면신경과 부신경가지(TE17), 설인신경(TE17), 설하신경(TE17), 경신경고리(TE17), 미주신경(TE17), 안면신경 (TE18). 3) 혈(血) 관(管) : 천층에 척측정맥배측지(TE1, 2), 고유수장지동맥배측지(TE1), 배측중수골동맥배측지(TE2), 배측중수골정맥(TE3), 척측피정맥(TE4, 5, 6, 7, 8, 9, 10, 11), 배측정맥궁(TE4), 부요측피정맥(TE6, 8, 9),요측피정맥(TE10, 11), 후견봉정맥가지(TE13, 14), 후이개동 ${\cdot}$ 정맥(TE16, 17, 18, 19, 20), 전이개동 ${\cdot}$ 정맥(TE20), 천측두동 ${\cdot}$ 정맥(TE22, 23), 중층에 후상완회선동맥(TE14), 견갑배동맥(TE15), 견갑상동맥(TE15),천측두동 ${\cdot}$ 정맥(TE21), 관골측두동 ${\cdot}$ 정맥(TE23), 심층에 배측중수골동맥(TE3), 배측수근동맥궁(TE4), 후골간동맥(TE4, 5, 6, 7, 8, 9), 전골간동맥(TE6, 7, 9), 심상완동맥(TE10, 11), 상완동맥측부지(TE10, 11), 중간 측부동맥(TE12), 요측측부동맥(TE12), 심상완동맥가지(TE13), 후상완회선동맥(TE13), 견갑상동맥(TE14), 후두동 ${\cdot}$ 정맥(TE16, 17), 내경정맥(TE17). 결 론 : 1. 수소양삼초경근(手少陽三焦經筋)은 근육(筋肉), 그리고 관련(關聯) 신경(神經), 혈관(血管)으로 구성된다. 2. 본 연구(硏究)는 경근(經筋)에 관한 기존(旣存)의 연구(硏究)와 비교(比較)하여 볼 때에 경근(經筋)의 구성요소(構成要素)에 있어서 약간(若干)의 차이(差異)를 보여준다. 3. 해부학적(解剖學的) 연구결동(硏究結東), 경근(經筋) 근육(筋肉)을 지배(支配)하는 신경(神經)${\cdot}$혈관(血管)의 개념(槪念)과 경근(經筋)을 스쳐 지나가는 신경(神經)${\cdot}$혈관(血管)의 개념(槪念)은 구분(區分)된다.

• Journal of Genetic Medicine
• /
• v.8 no.1
• /
• pp.44-52
• /
• 2011

Purpose: Cytogenetic analysis of spontaneous abortions (SABs) provides valuable information to establish the causes of fetal loss, information that is essential to provide accurate reproductive and genetic counseling couples. Such analysis also provides information on the frequencies and types of chromosomal abnormalities and associated risks of recurrence. However, there have only been a few reports of chromosomal abnormalities in small samples of SABs in the Korean population. Here, we report the incidence and spectrum of chromosomal abnormalities for cases of 470 SAB in Korea. Material and Methods: Between 2005 and 2010, a total of 470 products of conception (POC) resulting from SABs were submitted to our laboratory for cytogenetic analysis from various medical sites in Korea. The incidences and types of specific chromosomal abnormalities were determined. The abnormalities were distinguished by gestational age at the time of SAB and by maternal age. Results: The frequency of chromosomal abnormalities in POCs was 54.3% (255/470), including 228 (89.3%) numerical and 27 (10.7%: 3 balanced and 24 unbalanced) structural abnormalities. Among the numerical abnormalities, trisomy was predominant (67.0%), followed by monosomy X (12.5%), polyploidy (8.2%), triple X (0.8%), and autosomal monosomy (0.8%). The overall sex ratio (male: female) among the 470 POCs with normal and abnormal karyotypes were 0.58 and 0.65, respectively. Trisomies were identified for each autosome, with the exceptions of 1, 3, and 19. Among the 171 autosomal trisomies, trisomy 16 was the most common (19.9%), followed by trisomy 22 (13.5%), trisomy 21 (12.3 %), trisomy 15 (9.9%), and trisomies 18 and 13 (5.3%). The frequency of chromosomal abnormalities decreased with gestational age and increased with maternal age, but only because of increases in trisomies and complex abnormalities. Conclusions: We have presented a large collection of cytogenetic data for SABs collected during the past 6 years and provided a database for prenatal genetic counseling of parents who have experienced SABs in Korea.

• Journal of Korean Society of Forest Science
• /
• v.23 no.1
• /
• pp.1-8
• /
• 1974

The seed quality testing for Korean white pine (Pinus koraiensis), their pre-germination and embryo growing process were investigated and the abnormal embryo groups were discriminated by the use of soft X-ray photograph. The study results were as follows ; 1. The embryo reflection was clearly observed for air dried seeds (moisture content was 6.3%) at 30 sec, stratificated seeds at 60 sec (moisture content 24.0-36.0%) and immature seed (moisture content 41.0-64.0%) at 90sec., then the photographing variation for soft X-ray was the radiographing distance at 42cm focus M, voltage 19.5 K.V.P. and Ampere 8 mA. By the above result, the radiographing time for discriminating the embryo reflection was increased by the increase of moisture content in the seeds. 2. The embryo reflection could be clearly observed from the last ten days of June and the embryo length ratio to endosperm length was growing to 65% at the first ten days of September. By the result obtained the soft X-ray photograph was thought to be effective method for the study of inner morphology of seeds. 3. The clear reflection seeds for embryo and endorsperm were observed to 69.7% and the seeds were practically germinated to 75.2% The difference in number between the discriminated seeds by the soft X-ray photograph and the practically germinated seeds was only 6%. According to this results, the soft X-ray photograph was thought to be a effective methods for the germination diagnosis in the shortest time and with the exactness comparatively. 4. Because of the possibility of clearness for observation of pre-germination process, the soft X-ray photograph could be used for the study on the physiology of seed germination. 5. The frequency of abnormal embryos was observed of total 4.4% and their types and subtypes could be classified into twenty groups. Among these groups, single abnormal embryo type was divided into eight subtypes and observed of 2.0 percent, twin embryo was six subtypes and 1.8 percent, triple embryo was five subtypes and 0.5 percent, and inverse type was 0.12 percent.

• Journal of Intelligence and Information Systems
• /
• v.20 no.2
• /
• pp.149-162
• /
• 2014

Course guidance is a mentoring process which is performed before students register for coming classes. The course guidance plays a very important role to students in checking degree audits of students and mentoring classes which will be taken in coming semester. Also, it is intimately involved with a graduation assessment or a completion of ABEEK certification. Currently, course guidance is manually performed by some advisers at most of universities in Korea because they have no electronic systems for the course guidance. By the lack of the systems, the advisers should analyze each degree audit of students and curriculum information of their own departments. This process often causes the human error during the course guidance process due to the complexity of the process. The electronic system thus is essential to avoid the human error for the course guidance. If the relation data model-based system is applied to the mentoring process, then the problems in manual way can be solved. However, the relational data model-based systems have some limitations. Curriculums of a department and certification systems can be changed depending on a new policy of a university or surrounding environments. If the curriculums and the systems are changed, a scheme of the existing system should be changed in accordance with the variations. It is also not sufficient to provide semantic search due to the difficulty of extracting semantic relationships between subjects. In this paper, we model a course mentoring ontology based on the analysis of a curriculum of computer science department, a structure of degree audit, and ABEEK certification. Ontology-based course guidance system is also proposed to overcome the limitation of the existing methods and to provide the effectiveness of course mentoring process for both of advisors and students. In the proposed system, all data of the system consists of ontology instances. To create ontology instances, ontology population module is developed by using JENA framework which is for building semantic web and linked data applications. In the ontology population module, the mapping rules to connect parts of degree audit to certain parts of course mentoring ontology are designed. All ontology instances are generated based on degree audits of students who participate in course mentoring test. The generated instances are saved to JENA TDB as a triple repository after an inference process using JENA inference engine. A user interface for course guidance is implemented by using Java and JENA framework. Once a advisor or a student input student's information such as student name and student number at an information request form in user interface, the proposed system provides mentoring results based on a degree audit of current student and rules to check scores for each part of a curriculum such as special cultural subject, major subject, and MSC subject containing math and basic science. Recall and precision are used to evaluate the performance of the proposed system. The recall is used to check that the proposed system retrieves all relevant subjects. The precision is used to check whether the retrieved subjects are relevant to the mentoring results. An officer of computer science department attends the verification on the results derived from the proposed system. Experimental results using real data of the participating students show that the proposed course guidance system based on course mentoring ontology provides correct course mentoring results to students at all times. Advisors can also reduce their time cost to analyze a degree audit of corresponding student and to calculate each score for the each part. As a result, the proposed system based on ontology techniques solves the difficulty of mentoring methods in manual way and the proposed system derive correct mentoring results as human conduct.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.26 no.12
• /
• pp.605-619
• /
• 2014

This article reviews the papers published in the Korean Journal of Air-Conditioning and Refrigeration Engineering during 2013. It is intended to understand the status of current research in the areas of heating, cooling, ventilation, sanitation, and indoor environments of buildings and plant facilities. Conclusions are as follows. (1) The research works on the thermal and fluid engineering have been reviewed as groups of fluid machinery, pipes and relative parts including orifices, dampers and ducts, fuel cells and power plants, cooling and air-conditioning, heat and mass transfer, two phase flow, and the flow around buildings and structures. Research issues dealing with home appliances, flows around buildings, nuclear power plant, and manufacturing processes are newly added in thermal and fluid engineering research area. (2) Research works on heat transfer area have been reviewed in the categories of heat transfer characteristics, pool boiling and condensing heat transfer and industrial heat exchangers. Researches on heat transfer characteristics included the results for general analytical model for desiccant wheels, the effects of water absorption on the thermal conductivity of insulation materials, thermal properties of Octadecane/xGnP shape-stabilized phase change materials and $CO_2$ and $CO_2$-Hydrate mixture, effect of ground source heat pump system, the heat flux meter location for the performance test of a refrigerator vacuum insulation panel, a parallel flow evaporator for a heat pump dryer, the condensation risk assessment of vacuum multi-layer glass and triple glass, optimization of a forced convection type PCM refrigeration module, surface temperature sensor using fluorescent nanoporous thin film. In the area of pool boiling and condensing heat transfer, researches on ammonia inside horizontal smooth small tube, R1234yf on various enhanced surfaces, HFC32/HFC152a on a plain surface, spray cooling up to critical heat flux on a low-fin enhanced surface were actively carried out. In the area of industrial heat exchangers, researches on a fin tube type adsorber, the mass-transfer kinetics of a fin-tube-type adsorption bed, fin-and-tube heat exchangers having sine wave fins and oval tubes, louvered fin heat exchanger were performed. (3) In the field of refrigeration, studies are categorized into three groups namely refrigeration cycle, refrigerant and modeling and control. In the category of refrigeration cycle, studies were focused on the enhancement or optimization of experimental or commercial systems including a R410a VRF(Various Refrigerant Flow) heat pump, a R134a 2-stage screw heat pump and a R134a double-heat source automotive air-conditioner system. In the category of refrigerant, studies were carried out for the application of alternative refrigerants or refrigeration technologies including $CO_2$ water heaters, a R1234yf automotive air-conditioner, a R436b water cooler and a thermoelectric refrigerator. In the category of modeling and control, theoretical and experimental studies were carried out to predict the performance of various thermal and control systems including the long-term energy analysis of a geo-thermal heat pump system coupled to cast-in-place energy piles, the dynamic simulation of a water heater-coupled hybrid heat pump and the numerical simulation of an integral optimum regulating controller for a system heat pump. (4) In building mechanical system research fields, twenty one studies were conducted to achieve effective design of the mechanical systems, and also to maximize the energy efficiency of buildings. The topics of the studies included heating and cooling, HVAC system, ventilation, and renewable energies in the buildings. Proposed designs, performance tests using numerical methods and experiments provide useful information and key data which can improve the energy efficiency of the buildings. (5) The field of architectural environment is mostly focused on indoor environment and building energy. The main researches of indoor environment are related to infiltration, ventilation, leak flow and airtightness performance in residential building. The subjects of building energy are worked on energy saving, operation method and optimum operation of building energy systems. The remained studies are related to the special facility such as cleanroom, internet data center and biosafety laboratory. water supply and drain system, defining standard input variables of BIM (Building Information Modeling) for facility management system, estimating capability and providing operation guidelines of subway station as shelter for refuge and evaluation of pollutant emissions from furniture-like products.

• The Journal of the Petrological Society of Korea
• /
• v.18 no.3
• /
• pp.223-236
• /
• 2009

Ultramafic xenoliths from southeastern part of Jeju Island can be grouped into two types: Type I and Type II. Type I xenoliths are magnesian and olivine-rich peridotite (mg#=89-91), which are commonly found at the outcrop. Most previous works have been focused on Type I xenoliths. Type II xenoliths, consisting of olivine, orthopyroxene and clinopyroxene with higher Fe and Ti components (mg#=77-83) and lower Mg, Ni, Cr, are reported in this study. They are less common with a more extensive compositional range. The studied Type II xenoliths are wehrlite, olivine-clinopyroxenite, olivine websterite, and websterite. They sometimes show ophitic textures in outcrops indicating cumulate natures. The textural characteristics, such as kink banding and more straight grain boundaries with triple junctions, are interpreted as the result of recrystallization and annealing. Large pyroxene grains have exsolution textures and show almost the same major compositions as small exsolution-free pyroxenes. Although the exsolution texture indicates a previous high-temperature history, all mineral phases are completely reequilibrated to some lower temperature. Orthopyroxenes replacing clinopyroxene margin or olivine indicate an orthopyroxene enrichment event. Mineral phases of Type II are compared with Type I xenoliths, gabbroic xenoliths, and the host basalts. Those from Type II xenoliths show a distinct discontinuity with those from Type I mantle xenoliths, whereas they show a continuous or overlapping relation with those from gabbroic xenoliths and the host basalts. Our petrographic and geochemical results suggest that the studied type II xenoliths appear to be cumulates derived from the host magma-related system, being formed by early fractional crystallization, although these xenoliths may not be directly linked to the host basalt.