• Journal of Mechanical Science and Technology
• /
• v.19 no.9
• /
• pp.1790-1800
• /
• 2005

The examination on the operating mechanism of a pulsating heat pipe (PHP) using visualization revealed that the working fluid in the PHP oscillated to the axial direction by the contraction and expansion of vapor plugs. This contraction and expansion is due to the formation and extinction of bubbles in the evaporating and condensing section, respectively. In this paper, a theoretical model of PHP was presented. The theoretical model was based on the separated flow model with two liquid slugs and three vapor plugs. The results show that the diameter, surface tension and charge ratio of working fluid have significant effects on the performance of the PHP. The following conclusions were obtained. The periodic oscillations of liquid slugs and vapor plugs were obtained under specified parameters. When the hydraulic diameter of the PHP was increased to d=3mm, the frequency of oscillation decreased. By increasing the charging ratio from 40 to 60 by volume ratio, the pressure difference between the evaporating section and condensing section increased, the amplitude of oscillation reduced, and the oscillation frequency decreased. The working fluid with higher surface tension resulted in an increase in the amplitude and frequency of oscillation. Also the average temperature of vapor plugs decreased.

• Journal of Advanced Marine Engineering and Technology
• /
• v.36 no.7
• /
• pp.869-875
• /
• 2012

In the past decades, extensive studies on convection heat transfer on internal flow have been conducted by using high specific surface area, by increasing heat transfer coefficient and swirl flow, and by improving the transport properties. In this study, we applied a tangential slot swirl generator to improve heat transfer in a horizontal circular copper tube. The Al-Mg particles (approximately $100{\mu}m$ to $130{\mu}m$) were employed for this experimental work. The copper tube was heated uniformly by winding a heating coil with a resistance of 9 ohm per meter for heat transfer. Using Al-Mg particles, experiments were performed in the Reynolds number range of 5,000 to 13,130, with and without swirl. Experimental data transfers or comparisons between Nusselt numbers with and without swirl along the test tube and Reynolds numbers are presented. The Nusselt number is improved by increasing Reynolds numbers or swirl intensities along the test tube.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.6 no.3
• /
• pp.98-104
• /
• 2007

The carbon fiber reinforced carbon composite (CFRC) materials are necessary for the advanced industries that require the thermal resistance. And the development and research for CFRC has been in progress in the field of aerospace and defense industry. CFRC have several advantages and special properties such as excellent anti ablation, outstanding strength retention at very high temperature, high heat capacity and thermal transport, high specific stiffness and strength, and high thermal shock resistance. They have been used as aircraft brake, rocket nozzle, nose cones, jet engine turbine wheels, and high speed craft. Since the technology related to CFRC was prohibited from importing and exporting, we developed our own technology to produce F-16 B32 brake disk made out of CFRC, and then we performed various tests to observe the characteristics of CFRC-based brake disk developed in this study in view of density, strength, friction, specific heat, and heat conductivity.

• The Korean Journal of Community Living Science
• /
• v.25 no.3
• /
• pp.383-388
• /
• 2014

This study was examined the physical characteristics (geometry, yield strength, thousand-seeds weight, true density, and moisture content) required for mechanization-related technologies such as (harvesting, washing, transport, and drying). Large differences in the size and shape of boxthorn berries(Jangmyeong, Bullo, Chungmyeong, and Hokwang) are used to analyze these physical properties. The average diameter, volume, surface area, and sphericity rate are calculated using long and short diameters of the boxthorn berry according to its variety. Hokwang has the largest measured surface area, and Bullo, the smallest. Average yield strength is 1.78 kPa and the mechanical pressure of soft boxthorn berries is not more than 1 kPa. Bullo has the highest true density. The optimum drying time for the measurement of moisture content is 4 hours at the drying temperature of $100^{\circ}C$.

• Journal of the Korean Society of Visualization
• /
• v.3 no.1
• /
• pp.3-19
• /
• 2005

Novel optical techniques are presented for three-dimensional tracking of nanoparticles; Optical Serial Sectioning Microscopy (OSSM) and Ratiometric Total Internal Reflection Fluorescent Microscopy (R-TIRFM). OSSM measures optically diffracted particle images, the so-called Point Spread Function (PSF), and dotermines the defocusing or line-of-sight location of the imaged particle measured from the focal plane. The line-of-sight Brownian motion detection using the OSSM technique is proposed in lieu of the more cumbersome two-dimensional Brownian motion tracking on the imaging plane as a potentially more effective tool to nonintrusively map the temperature fields for nanoparticle suspension fluids. On the other hand, R-TIRFM is presented to experimentally examine the classic theory on the near-wall hindered Brownian diffusive motion. An evanescent wave field from the total internal reflection of a 488-nm bandwidth of an argon-ion laser is used to provide a thin illumination field of an order of a few hundred nanometers from the wall. The experimental results show good agreement with the lateral hindrance theory, but show discrepancies from the normal hindrance theory. It is conjectured that the discrepancies can be attributed to the additional hindering effects, including electrostatic and electro-osmotic interactions between the negatively charged tracer particles and the glass surface.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.27 no.5
• /
• pp.596-603
• /
• 2003

Present study has been conducted to see the relative effects of adding N: to fuel-side and air-side on flame structure, soot formation and NOx emissions. Experiments were carried out to ascertain to what degree chemical kinetics and/or molecular transport effects can explain the differences in soot formation and NOx emission by studying laminar diffusion flames. Direct photograph was taken to see the flame structure. CARS techniques was used to get the flame temperature profiles. And spatial distribution of soot could be obtained by PLII method. CHEMKIN code was also used to estimate the global residence time to predict NOx emissions at each condition. Results from these studies indicate that fuel-side dilution is more effective than air-side dilution in view of NOx emissions. However, air-side dilution shows greater effectiveness over fuel-side dilution in soot formation. And turbulent mixing and heat transfer problems were thought to be considered in practical applications.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.1 no.3
• /
• pp.158-166
• /
• 2001

Based on uniform hot carrier injection (optically assisted electron injection) across the $Si-SiO_2$ interface into the gate insulator of n-channel IGFETs, the threshold voltage shifts associated with electron injection of $1.25{\times}l0^{16}{\;}e/\textrm{cm}^2 between 0.5 and 7 MV/cm were found to decrease from positive to negative values, indicating both a decrease in trap cross section ($E_{ox}{\geq}1.5 MV/cm$) and the generation of FPC $E_{ox}{\geq}5{\;}MV/cm$). It was also found that FNC and large cross section NETs were generated for $E_{ox}{\geq}5{\;}MV/cm$. Continuous, uniform low-field (1MV/cm) electron injection up to $l0^{19}{\;}e/\textrm{cm}^2 is accompanied by a monatomic increase in threshold voltage. It was found that the data could be modeled more effectively by assuming that most of the threshold voltage shift could be ascribed to generated bulk defects which are generated and filled, or more likely, generated in a charged state. The injection method and conditions used in terms of injection fluence, injection density, and temperature, can have a dramatic impact on what is measured, and may have important implications on accelerated lifetime measurements.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.14 no.5
• /
• pp.424-432
• /
• 2002

Numerical analysis has been conducted to characterize deposition rates of aerosol particles onto a heated, rotating disk with electrostatic effect under the laminar flow field. The particle transport mechanisms considered were convection, Brownian diffusion, gravitational settling, thermophoresis and electrophoresis. The aerosol particles were assumed to have a Boltzmann charge distribution. The electric potential distribution needed to calculate local electric fields around the disk was calculated from the Laplace equation. The Coulomb, the image, the dielectrophoretic and the dipole-dipole forces acting on a charged particle near the conducting rotating disk were included in the analysis. The averaged particle deposition vetocities and their radial distributions on the upper surface of the disk were calculated from the particle concentration equation in a Eulerian frame of reference, along with a rotation speed of 0∼1,000rpm, a temperature difference of 0∼5K and a charged disk voltage of 0∼1000V.Finally, an approximate deposition velocity model for the rotating disk was suggested. The present numerical results showed relatively good agreement with the results of the present approximate model and the available experimental data.

• Korean Journal of Pharmacognosy
• /
• v.7 no.1
• /
• pp.3-13
• /
• 1976

The hitherto existing gap in the field of chromatographic methods has been filled by the direct coupling of a suitable oven (TAS-oven) with TLC. The sample to be examined is heated either isothermally or linearly within the temperature gradient of $50{\sim}450^{\circ}C$. The volatile and/or thermolytically evolved substances are fractionated on the TLC-layer and subsequently chromatographed under standard conditions. Transport mechanisms from the sample to the TLC-layer, applications of the TAS-procedure and further developments are discussed. Thermofractography, developed from the TAS-procedure, is demonstrated on different groups of natural substances such as alkaloids, amino acids, nucleic acids. nucleosides, nucleotides, triglycerides and other lipids, pyrone glycosides and aglycon. Experimental work and results on the thermolysis of macromolecular natural and synthetic substances, natural polyphenols, tanning agents and leather and the possibilities of differentiating various lignins, carbohydrate and synthetic polymers are reported. Further, it is shown that classical reactions in the microgram range, e.g. zinc dust distillation, sulphur-and selenium dehydrogenation and catalytic dehydrogenation, can be coupled directly with TLC. Also described is a method which allows to investigate the gaseous compounds evolved during thermofractography in the range of up to $450^{\circ}C$. Thermal procedures coupled with TLC open up the following new possibilities for chemical microanalysis: fractionated separation of distillable and sublimable components, fractionated thermolysis and carrying out of thermal reactions in the ultra micro range.

• Journal of the Korean Society of Visualization
• /
• v.10 no.3
• /
• pp.16-20
• /
• 2012

In the past decades, extensive studies on convection heat transfer on internal flow have been conducted by using high specific surface area, by increasing heat transfer coefficient and swirl flow, and by improving the transport properties. In this study, we applied a tangential slot swirl generator to improve heat transfer in a horizontal circular copper tube. The Al-Mg particles (approximately $100{\mu}m$ to $130{\mu}m$) were employed for this experimental work. The copper tube was heated uniformly by winding a heating coil with a resistance of 9ohm per meter for heat transfer. Using Al-Mg particles, experiments were performed in the Reynolds number range of 5,000 to 13,130, with and without swirl. Experimental data transfers or comparisons between Nusselt numbers with and without swirl along the test tube and Reynolds numbers are presented. The Nusselt number is improved by increasing Reynolds numbers or swirl intensities along the test tube.