• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.248-248
• /
• 2016

We have investigated the crystallinity, preferential ordering, and interfacial stability of 1,4,5,8,9,11-hexaazatriphenylene-hexanitrile (HATCN) thin film interconnected with organic/inorganic multilayer. At the region close to the organic-organic interface, HATCN formed low crystalline order with substantial amorphous phase. As film growth continued, HATCN stacked with high crystalline phase. After a sputtering deposition of the indium zinc oxide (IZO) layer on top of HATCN/organic layer, the volume fraction of preferentially ordered HATCN crystals increased without any structural deterioration. In addition, the HATCN surface was kept quite stable by preserving the sharp interface between HATCN and sputtering deposited IZO layers.

• Applied Science and Convergence Technology
• /
• v.24 no.2
• /
• pp.41-46
• /
• 2015

Transparent conductive oxides (TCOs) are essential material in optoelectronics such as solar cells, touch screens and light emitting diodes. Particularly TCOs are attractive material for infrared cut off film due to their high transparency in the visible wavelength range and high infrared reflectivity. Among the TCO, Indium tin oxide has been widely used because of the high electrical conductivity and transparency in the visible wavelength region. But ITO has several limitations; expensive and low environmental stability. On the other hands, fluorine doped tin oxide (FTO) is well known for low cost, weather ability and stable in acidic and hydrogen. In this study, two different magnetron sputtering techniques with RF and DC modes at room temperature deposition of FTO thin film was conducted. The change of oxygen content is influence on the topography, transmittance and refractive index.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2009.11a
• /
• pp.50.1-50.1
• /
• 2009

Transparent conductive oxides (TCOs) play an important role in thin-film solar cells in terms of low cost and performance improvement. Al-doped ZnO (AZO) is a very promising material for thin-film solar cellfabrication because of the wide availability of its constituent raw materials and its low cost. In this study, AZO films were prepared by low pressurechemical vapor deposition (LPCVD) using trimethylaluminum (TMA), diethylzinc(DEZ), and water vapor. In order to improve the absorbance of light, atypical surface texturing method is wet etching of front electrode using chemical solution. Alternatively, LPCVD can create a rough surface during deposition. This "self-texturing" is a very useful technique, which can eliminate additional chemical texturing process. The introduction of a TMA doping source has a strong influence on resistivity and the diffusion of light in a wide wavelength range.The haze factor of AZO up to a value of 43 % at 600 nm was achieved without an additional surface texturing process by simple TMA doping. The use of AZO TCO resulted in energy conversion efficiencies of 7.7 % when it was applied to thep-i-n a-Si:H thin film solar cell, which was comparable to commercially available fluorine doped tin oxide ($SnO_2$:F).

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.358-358
• /
• 2012

The application of BZO (Boron-doped Zinc Oxide) films use as the TCO(Transparent Conductive Oxide) material for display and solar cell industries, where the conductivity of the BZO films plays a critical role for improvement of cell performance. Thin BZO films are deposited on glass substrates by using RF sputter system. Then charging flow rates of O2 gas from zero to 10 sccm, thereby controlling the impurity concentration of BZO. BZO deposited on soda lime glass and RF power was 300 W, frequency was 13.56 MHz, and working pressure was $5.0{\times}10-6$ Torr. The Substrate and glass between distance 200 mm. We measured resistivity, conductivity, mobility by hall measurement system. Optical properties measured by photo voltaic device analysis system. We measured surface build according to oxygen flow rate from XPS (X-ray Photoelectron Spectroscopy) system. The profile of the energy distribution of the electrons emitted from BZO films by the Auger neutralization is measured and rescaled so that Auger self-convolution arises, revealing the detail structure of the valence band. It may be observed coefficient ${\gamma}$ of the secondary electron emission from BZO by using ${\gamma}$-FIB (Gamma-Focused Ion Beam) system. We observed the change in electrical conductivity by correlation of the valence band structure. Therefore one of the key issues in BZO films may be the valence band that detail structure dominates performance of solar cell devices. Demonstrating the secondary electron emission by the Auger neutralization of ions is useful for the determination of the characteristics of BZO films for solar cell and display developments.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.447-447
• /
• 2009

In this study, transparent and conductive Al-doped zinc oxide (AZO) films were prepared on Corning glass and silicon wafer substrate by RF magnetron sputtering method using an Al-doped ZnO target (Al: 2 wt.%) at room temperature as the thickness of 150 nm. We investigated the effects of the RF power between 100 Wand 350 W in steps of 50 W on structural, electrical and optical properties of AZO films. Also, we studied the effects of the working pressure (3, 4 and 5 mtorr) on that condition. The thickness and cross-sectional images of films were observed by field emission scanning electron microscopy (FE-SEM) and all of the films were kept to be constant to $150\pm10$ nm on Coming glass and silicon wafer. A grain size was calculated from X-ray diffraction (XRD) on using the Scherrer' equation and their electrical properties investigated hall effect electronic transport measurement system. Moreover, we measured transmittance of AZO films by UV/VIS spectrometer.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.303-304
• /
• 2008

Al, N-codoped ZnO(ZnO:N,Al) thin films were deposited on n-type Si(100) substrate at $450^{\circ}C$ with various conditions of ambient gas$(N_2:O_2)$ by DC magnetron sputtering method using ZnO:$Al_2O_3$(2wt%) as a target, and then were annealed at 500, 700, $800^{\circ}C$ in $N_2$ gas for one hour. XRD patterns showed that all of the ZnO:N,Al thin films annealed at $80^{\circ}C$ grew with two peaks, which means poor crystallinity of the thin films deposited. Hall effects in Van der Pauw configuration proved that after annealing the films deposited showed low resistivity and high carrier concentration. While the films annealed at $800^{\circ}C$ showed low resistivity of $\sim10^{-2}\Omega$ cm and high carrier concentration of $\sim10^{19}cm^{-3}$.

• Korean Journal of Materials Research
• /
• v.34 no.1
• /
• pp.55-62
• /
• 2024

Fluorine-doped tin oxide (FTO) has been used as a representative transparent conductive oxide (TCO) in various optoelectronic applications, including light emitting diodes, solar cells, photo-detectors, and electrochromic devices. The FTO plays an important role in providing electron transfer between active layers and external circuits while maintaining high transmittance in the devices. Herein, we report the effects of substrate rotation speed on the electrical and optical properties of FTO films during ultrasonic spray pyrolysis deposition (USPD). The substrate rotation speeds were adjusted to 2, 6, 10, and 14 rpm. As the substrate rotation speed increased from 2 to 14 rpm, the FTO films exhibited different film morphologies, including crystallite size, surface roughness, crystal texture, and film thickness. This FTO film engineering can be attributed to the variable nucleation and growth behaviors of FTO crystallites according to substrate rotation speeds during USPD. Among the FTO films with different substrate rotation speeds, the FTO film fabricated at 6 rpm showed the best optimized TCO characteristics when considering both electrical (sheet resistance of 13.73 Ω/□) and optical (average transmittance of 86.76 % at 400~700 nm) properties with a figure of merit (0.018 Ω^-1).

• Korean Chemical Engineering Research
• /
• v.43 no.1
• /
• pp.85-91
• /
• 2005

$SnO_2$ films were prepared at room temperature under a $(CH_3)_4Sn-H_2-O_2$ atmosphere in order to obtain transparent conductive polymer by using ECR-MOCVD (Electron Cyclotron resonance -Metal Organic Chemical Vapor Deposition) system. The electrical properties of the films were investigated as function of process parameters such as deposition time, microwave power, magnetic current power, magnet/showering/substrate distance and working pressure. An increase in microwave power and magnetic current power brought on $SnO_2$ film formation with low electric resistivity. On the other hand, the effects of process parameters described above on optical properties were insignificant in the range of our experimental scope. The transmittance and reflectance of the films prepared by the ECR-MOCVD exhibited their average values of 93-98% at wave length range of 380-780 nm and 0.1-0.5%, respectively. The grain size of the $SnO_2$ films that are also insensitive with the process parameters were in the range of 20-50 nm. On the basis of experimental data obtained in the present study, electrical resistivity of $7.5{\times}10^{-3}ohm{\cdot}cm$, transmittance of 93%, and reflectance of 0.2% can be taken as optimum values.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.1437-1439
• /
• 2009

Electrical and optical properties of $SiO_2$-doped ZnO (SZO) films on the corning 7059 glass substrates by using rfmagnetron sputtering method are investigated. The deposition rate becomes maximum near 3 wt.% and gradually decreases when the $SiO_2$ content further increases. The growth rates at 3 wt.% is $4^{\circ}$A/s. We found that the average transmittance of all films is over 80% in the wavelength range above 500 nm. The optical band gap decreases from 3.52 to 3.33 eV with an increase in thickness. X-ray diffraction patterns show that the film with a relatively low $SiO_2$ content (< 4 wt.%) is amorphous. SZO films at the $SiO_2$ contents of 2 wt.% shows the resistivity of about $3.8{\times}10^{-3}{\cdot}cm$. The sheet resistance decreases with increasing the heat treatment temperature.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.37 no.2
• /
• pp.169-174
• /
• 2024

In this study, the structural, electrical, and optical properties of AZO films of various thicknesses are compared. The AZO films were deposited on a glass substrate by FTS (Facing-Target-Sputtering) This research was conducted to find the optimal thickness for Transparent Conductive Oxide (TCO). AZO has suitable properties for TCO such as low resistivity, and high transmittance. Thin films of all thicknesses showed a transmittance of over 80% in the visible light region and electrical properties improved as thickness increased. It was confirmed that the film of 300 nm thick had the best performance due to its low resistivity, and uniform surface. This research is expected to help find optimal conditions in various fields where TCO is used, such as solar cells, displays, and sensors in the future.