• The Transactions of the Korean Institute of Power Electronics
• /
• v.16 no.6
• /
• pp.533-541
• /
• 2011

This paper studies modeling of Jeju 80kV HVDC system and its controller by using PSCAD/EMTDC program. Reduced ac network is applied to verify interaction between ac network and dc system. Design parameter is applied to the converter transformer, harmonic filter and dc transmisstion line to simulate dc system. HVDC controller is divided into a rectifier controller and a inverter controller according to the converter operating mode. The inverter controller is composed of current control, voltage control and extingtion angle control. The rectifier controller is composed of current control and voltage control. Both controller has VDCOL characteristics so that current order is dependant on voltage variation. Step response, ac network single phase fault, three phase fault is simulated to verify the dynamic performance of controller model in both transient state and steady state.

• Korean Journal of Optics and Photonics
• /
• v.18 no.2
• /
• pp.155-161
• /
• 2007

A new and simple method of 3-dimensional circuit modeling and analysis is proposed and verified experimentally for the first time by determining 3-dimensional current flow and 2-dimensional light distribution in blue InGaN/GaN multi-quantum well (MQW) light emitting diode (LED) devices. Circuit parameters of the LED consist of the resistance of the metallic film and epitaxial layer, and the intrinsic diode which represents the active region emitting the light. The circuit parameters are extracted from the transmission line model (TLM) and current-voltage relation. We applied the >> proposed method and extracted circuit parameters to obtain the light emission pattern in a top-surface emitting-type LED. The current spreading effect is analyzed theoretically and quantitatively with a variation of the resistance of metallic and epitaxial layers. The emitting-light distribution of the fabricated blue LED showed a good agreement with the analyzed result, which shows the dark emission intensity at the corner of the p-electrode.

• The KIPS Transactions:PartC
• /
• v.13C no.7 s.110
• /
• pp.881-888
• /
• 2006

The position of the bridged tap is determined by that of the outlet in most modern apartments, since most of the indoor wiring utilizes the bus wiring structure when deploying the indoor communication line. These bridged taps deteriorate transmission performance in the specific frequency at the time of high-speed multimedia communication, which uses a high frequency bandwidth, since the duality of return loss worsens and line attenuation increases rapidly. As a result, analysis on this phenomenon is required. In this study, the test model is created by modeling the intercommunication facility of the apartment that is the most representative residential house type, and by understanding the structure and the environment of the indoor wiring. Also, how the bridge tap affects performance is analyzed when the VDSL service is provided, so that problems of intercommunication lines can be identified and methods for improving the proper intercommunication line can be suggested, which is suitable for accommodating high-speed multimedia service of the future.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.12 no.3
• /
• pp.320-330
• /
• 2012

In this paper, we investigate the power integrity of grid structures for power and ground distribution on printed circuit board (PCB). We propose the 2D transmission line method (TLM)-based model for efficient frequency-dependent impedance characterization and PCB-package-integrated circuit (IC) co-simulation. The model includes an equivalent circuit model of fringing capacitance and probing ports. The accuracy of the proposed grid model is verified with test structure measurements and 3D electromagnetic (EM) simulations. If the grid structures replace the plane structures in PCBs, they should provide effective shielding of the electromagnetic interference in mobile systems. An analytical model to predict the shielding effectiveness (SE) of the grid structures is proposed and verified with EM simulations.

• Journal of Power Electronics
• /
• v.9 no.2
• /
• pp.133-145
• /
• 2009

In this paper a modular high performance MV-to-LV rectifier based on a cascaded H-bridge rectifier is presented. The proposed rectifier can directly connect to the medium voltage levels and provide a low-voltage and highly-stable DC interface with the consumer applications. The input stage eliminates the necessity for heavy and bulky step-down transformers. It corrects the input power factor and maintains the voltage balance among the individual DC buses. The second stage includes the high frequency parallel-output DC/DC converters which prepares the galvanic isolation, regulates the output voltage, and attenuates the low frequency voltage ripple ($2f_{line}$) generated by the first stage. The parallel-output converters can work in interleaving mode and the active load-current sharing technique is utilized to balance the load power among them. The detailed analysis for modeling and control of the proposed structure is presented. The validity and performance of the proposed topology is verified by simulation and experimental results.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.43 no.7
• /
• pp.1206-1213
• /
• 1994

This paper presents the operation principle and design rule of the Rogowski coil which can measure the transient current and describes the calibration and application experimental results for performance evaluation. It is obtained that the response curves of the Robowski coil with the turns of 300 and the passive integrator to sinusoidal input give a good linearity up to the frequency of 500 [kHz] and the current measurement system gaving the Rogowski coil is the frequency bandwidth of 40 [Hz]~700 [kHz]. As an application experiment for the fabricated modeling power transmission line, the impulse current, which limitates the direct lightning return stroke to overhead ground wire, is measured by the Rogowski coil and its fast Fourier transformation is carried out. The equivalent circuit of the Rogowski coil considering the stray capacitances is proposed, and the theoretical analysis is in good agreement with the measurement results. Also, it is found that for high frequency domain the stray capacitance such as a distributed capacitance to the shield and the capacitance between windings of coil should be considered in designing the Rogowski coils since the resonance originates from the stray capacitance and the self-inductance of the Rogowski coil.

• Proceedings of the KIEE Conference
• /
• 2000.07b
• /
• pp.623-625
• /
• 2000

For the finite element analysis of highly saturated rotating machines involving rotation of a rotor such as dynamic analysis. cogging torque analysis and etc, so much time is needed because a new system matrix equation should be solved for each iteration and time step. It is proved in this paper that. in linear systems. the computational time can be greatly reduced by using the domain decomposition method (DDM). In nonlinear systems. however. this advantage vanishes because the stiffness matrix changes at each iteration especially when using the Newton-Raphson (NR) method. The transmission line modeling (TLM) method resolves this problem because in TLM method the stiffness matrix does not change throughout the entire analysis. In this paper, a new technique for FEA of rotating machines including rotation of rotor and non-linearity is proposed. This method is applied to a test problem. and compared with the conventional method.

• Journal of Advanced Marine Engineering and Technology
• /
• v.37 no.5
• /
• pp.527-532
• /
• 2013

The wireless visible light communication technology has received great attention for high-data rate services in the room and underwater. However, performance of a visible light seawater link is limited by multiple constraints from the current light source and detector technology, and underwater channel conditions. In this paper, performance of the line of sight underwater link was analyzed in terms of signal to noise ratio and bit error rate of the detector. Roles of different parameters such as data rate, transmission distance, and attenuation coefficient, are studied. Through the modeling and simulation of the OOK and L-PPM modulation technologies for undersea environment application, the advantages and limitations are described in detail.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.27 no.9C
• /
• pp.829-835
• /
• 2002

DSL(digital subscriber line) transceiver designers have concerned the impulsive noise as well as NEXT(near-end crosstalk) and FEXT(far-end crosstalk) immunities Down as the strongest sources that limit the DSL channel capacity. In these noise environment the analysis on the performance of DSL should be needed. Therefore, in this paper we have estimated and simulated the SNR(signal-to-noise ratio) margin of DMT(discrete multi-tone) signal in Gauss, NEXT, FEXT and impulse noise environment by modeling an Middleton's Class A impulse signal with the test Cook pulses. As a result, it is known that the transmission rate of uplink is limited by noise characteristics rather than by loop length, but that of downlink limited complexly by both of noise characteristics and loop length. In conclusion, these results will be utilized as the threshold of ADSL performance in the complex noise environment including impulse noise.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.39 no.8
• /
• pp.52-63
• /
• 2002

In this paper, we developed a numerical analysis model by using ADI-FDTD method to analyze three-dimensional interconnect structure. We discretized maxwell's curl equation by using ADI-FDTD. We introduced PML(Perfectly Matched Layer) absorbing boundary condition to solve the effect of the reflected wave at the interface. Evaluating the numerical model of PML and ADI-FDTD, we simulated the electric field distribution in time domain. We compare standard FDTD with ADI-FDTD, and analysis the result.