• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2018년도 춘계학술대회 논문집
• /
• pp.43.2-43.2
• /
• 2018

송전 및 배전선 선로에 사용되는 핵심 부품인 ACSR (Aluminum Conductor Steel Reinforced, 강심 알루미늄 연선) cable은 우수한 기계적 성질, 가벼운 중량, 내부식성 특징을 가지고 있어 송전 및 배전선 선로에 핵심 부품으로 사용된다. 하지만, 국내외 혹한 다설 지역에 설치된 ACSR cable에서 빙설해로 인한 단락 또는 지락 사고가 지속적으로 발생하고 있다. 빙설해에 의한 송전선로의 고장은 급격한 전압 강하로 인해 전기 품질에 큰 영향을 주어 민원제기의 주요 원인이 되며, 고장의 파급효과가 국지적으로 발생하지 않고 광범위하게 발생하는 특징이 있기 때문에 이에 대한 대응이 필요한 실정이다. 이러한 문제를 해결하기 위해 ACSR cable의 주 소재인 알루미늄에 대한 판상(Plate) 결빙강도 파악 및 결빙방지 소재개발 연구가 국내외에서 활발히 진행 중이나, 실제 원형의 전선다발이 나선형으로 감겨있는 구조의 ACSR cable 결빙 접합강도를 시험을 통해서 명확히 제시한 연구결과는 아직 보고된 바 없다. 본 연구에서는 실제 송전용 ACSR cable을 대상으로 얼음 간의 주 전단 응력, 파단에너지 등의 결빙특성을 정량적으로 측정할 수 있는 3D 스캔을 활용한 결빙특성 평가시험기를 개발하고, 345kV급 ACSR cable에 대한 결빙특성을 평가결과를 제시하였다. 또한 ACSR cable에 현재 상용화되고 있는 결빙방지 코팅소재를 적용함으로써 코팅소재의 적합성을 ARF(Adhesion reduction factor) 지표를 통해서 비교 평가한 결과를 포함한다.

• 센서학회지
• /
• 제15권6호
• /
• pp.386-390
• /
• 2006

This paper describes the ohmic contact formation of polycrystalline 3C-SiC films deposited on thermally grown Si wafers. In this work, a TiW (titanium tungsten) film as a contact material was deposited by RF magnetron sputter and annealed with the vacuum process. The specific contact resistance (${\rho}_{c}$) of the TiW contact was measured by using the C-TLM (circular transmission line method). The contact phase and interfacial reaction between TiW and 3C-SiC at high-temperature as also analyzed by XRD (X-ray diffraction) and SEM (scanning electron microscope). All of the samples didn't show cracks of the TiW film and any interfacial reaction after annealing. Especially, when the sample was annealed at $800^{\circ}$ for 30 min., the lowest contact resistivity of $2.90{\times}10{\Omega}cm^{2}$ was obtained due to the improved interfacial adhesion. Therefore, the good ohmic contact of polycrystalline 3C-SiC films using the TiW film is very suitable for high-temperature MEMS applications.

• Journal of electromagnetic engineering and science
• /
• 제16권1호
• /
• pp.7-12
• /
• 2016

This paper presents the design of a negative group delay circuit (NGDC) using the filter synthesis approach. The proposed design method is based on a frequency transformation from a low-pass filter (LPF) to a bandstop filter (BSF). The predefined negative group delay (NGD) can be obtained by inserting resistors into resonators. To implement a circuit with a distributed transmission line, a circuit conversion technique is employed. Both theoretical and experimental results are provided for validating of the proposed approach. For NGD bandwidth and magnitude flatness enhancements, two second-order NGDCs with slightly different center frequencies are cascaded. In the experiment, group delay of $5.9{\pm}0.5ns$ and insertion loss of $39.95{\pm}0.5dB$ are obtained in the frequency range of 1.935-2.001 GHz.

• 전자공학회논문지A
• /
• 제28A권9호
• /
• pp.721-728
• /
• 1991

In this paper, a magneto-optic modulator has been designed by using single crystal BSO and polycrystal ZnSe as Faraday cells. And practical core-type optical current sensors using pure iron and permalloy have been prepared and experimented. In order to obtain efficient magnetic field detection, LED(NEC OD08358, 0.87 $\mu$m) was used as optical source, PIN-PD(OD-8454)as optical receiver and multi-mode optical fiber (100/140$\mu$m) as transmission line. The characteristics matrix of the optical element was calculated by Stokes parameter, and optic modulation characteristics equations were derived by Muller matrix. Electromagnetic analysis program (FLUX 2D, micro VAX 3600) by finite element method was used to find the magnetic flux density around the core. The measuring error of the output voltage to input current has been masured below 5% in the range of 50A to 1000A. As the temperature was changed from -20$^{\circ}C$ to 60$^{\circ}C$, the maximum measurement error of the optical output has been found to be 0.5% at 60$^{\circ}C$. These experimental results show good temperature and linearity characteristics. The SNR of the overall system was 47dB in case of 600A (250.2 Oe) conductor current and the system has good noise immunity.

• Journal of Magnetics
• /
• 제21권1호
• /
• pp.61-64
• /
• 2016

In this study, we report the as-prepared MgO-doped $BaFe_{12}O_{19}$, which was prepared by calcination technique and high-energy ball milling process, as an electromagnetic wave absorber. The phase analysis of $BaFe_{12}O_{19}$ and the as-prepared MgO-doped $BaFe_{12}O_{19}$ was detected utilizing X-ray Diffractometer (XRD). The microstructure was characterized using Scanning Electron Microscope (SEM). By means of the transmission/reflection coaxial line method, the electromagnetic properties and microwave absorbing properties of the as-prepared electromagnetic wave absorber were studied. It is found that the electromagnetic wave absorber has a minimum reflection loss value of -41 dB at 4.27 GHz with a matching thickness of 2.6 mm. The experiment results revealed that the as-prepared electromagnetic wave absorber could find potential applications in many military as well as commercial industries.

• 대한의용생체공학회:학술대회논문집
• /
• 대한의용생체공학회 1993년도 춘계학술대회
• /
• pp.38-41
• /
• 1993

For efficient transmission and storage of digital images, the requirements of image compression is incresing. Because the medical images contain diagnostic information small distortion has been more important factor than the low rate in such images. Generally the distortion in image is the difference of pixel values. However the image is percieved by human visual systems. So it is reasonable that human visual system characteristics be used as criteria of the image compression. In this paper, the Just Noticeable Difference curve is used as criteria of determining the homogeniety of a block and acceptibility of distortions. And Block Truncation Coding using spatial masking effect of eyes is adopted to code the blocks which contain line components. And small blocks which varies slowly can be approximated to polynomial functions successfully. We proposed the hybrid block coding scheme based on the block characteristics and human visual system characteristics. Simulation to several kinds of the medical images using this method showed that medical images can be compressed 5:1 - 10:1 without noticeable distortion.

• 한국분말재료학회지
• /
• 제6권1호
• /
• pp.27-35
• /
• 1999

A study was made on the fabrication of nanostructured Fe-Co powders by mechanical alloying and their magnetic properties. Microstrural development during the process of MA was inverstigated by means of X-ray diffraction, differential thermal analyzer, scanning electron microscopy and transmission electron microscopy. The magnetic properties of NS Fe-Co powders were evaluated through the measurements of the saturation magnetization $(M_s)$ as well as the coercivity $(H_c)$. The average grain size calculated from line braodening in XRD peak was about 10nm or less and confirmed by TEM. In this experiment, two different milling methods (cycle opertion and conventional milling) were used. Cycle operation had an advantage over the conventional milling method in that more refined powders can be obtained. Solid state alloying of the components was confirmed from both the change of the saturation magnetization and the change of lattice parameter with Co contentration. Maxium $M_s$ was obtained at the composition of 30at.%Co. Relatively high coercivities of 10~150e were obtained for the compositions investigated, and this seems to be due to the high amount of internal strain introduced during milling.

• 제어로봇시스템학회논문지
• /
• 제16권1호
• /
• pp.25-32
• /
• 2010

The paper proposes a hierarchical fault detection method for the high voltage equipment using a microphone array which detects the location of fault and the thermal imaging and CCD cameras which verifies the fault and stores the image, respectively. There are partial arc discharges on the faulty insulators, which generates a specific pattern of sound. Detecting the signal using the microphone array, the location of the faulty insulator can be estimated. The 6th band-pass filter was applied to remove noise signal from wind or external influence. When the mobile robot carries the thermal and CCD cameras to the possible place of the fault insulator, the fault insulators or power transmission wires can be detected by the thermal images, which are caused by the aging or natural erosion. Finally, the CCD camera captures the image of the fault insulator for the record. The detection scheme of fault location using the microphone array and the thermal images have been proved to be effective through the real experiments. As a result of this research, it becomes possible to use a mobile robot with the integrated sensors to detect the fault insulators instead of a human being.

• 전자공학회논문지D
• /
• 제36D권8호
• /
• pp.19-26
• /
• 1999

개방단말 동축선 프로브의 제작오차가 프로브에 접촉된 매질의 복소유전율 측정에 얼마나 강한 영향을 미치는 지를 살펴보기 위한 수치계산을 수행하였다. 몇 가지 종류의 유전체를 접촉시킨 개방단말 동축선 프로브의 반사계수는 FDTD 방법을 적용해 수치계산 하였다. 이러한 계산된 반사계수들을 새로운 가상의 전송선 모델에 적용시켜 복소유전율로 확산하였는데, 본 논문에서 사용한 방법은 기존의 방법보다 물리적으로 더 의미가 있는 방법이다. 개방단말 프로브에 약간의 제작오차가 있을 때에도 복소유전율에는 큰 오차가 발생함을 알 수 있었다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 하계학술대회 논문집 Vol.9
• /
• pp.25-26
• /
• 2008

Electrical properties of Pt/Ti/Au/Pt contacts to n-GaAs were characterized as the V/III ratio of GaAs grown by metalorganic chemical vapor deposition were 25, 50, and 100, respectively. The samples have been annealed during 30sec at 350 and $450^{\circ}C$ in rapid thermal annealing, and those specific contact resistance investigated by using transmission line method. According to experimental results, the specific contact resistance between p-metal and GaAs was decreased as the V/III ratio was lower. These results indicate that Si doping concentration of GaAs increased as the vacancy of V-series of GaAs was high.