• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 춘계학술대회논문집A
• /
• pp.684-689
• /
• 2000

In this paper, the equations of motion about vehicle, powertrain and brake system were derived. The vehicle has eight degrees of freedom with nonlinear tire model and the powertrain has two degrees of freedom containing engine, torque converter and four speed automatic transmission. The brake system has two states about front and rear brake line pressures. The transient tire model with first order time lag is also subjoined for low speed or stop-and-go simulation. The modeling was derived considering two points - the fidelity and the simplicity. The simulation using this model is similar with real vehicle dynamic behavior and the model is made as simple as possible far fast simulation. It is validated that the derived vehicle model can be applicable to the real time simulation.

• 동력기계공학회지
• /
• 제6권2호
• /
• pp.73-81
• /
• 2002

In this study, electronically controlled automatic transmission adopted on a subcompact model in the market was modelled, and the driving performances of the transmission were simulated with the models. Kinetic and dynamic models of working components are established. The driving simulation program is developed with those models, and the various driving conditions are analyzed. With the results, the dynamic behaviour of the engine and the automatic transmission is easily understood. Especially, the transient performances of torque converter and clutches are deeply analyzed. Skipping the vehicle road test by using this analyzing tool, we can expect the cost down and the reduction of the development period of automatic transmission.

• Tribology and Lubricants
• /
• 제17권6호
• /
• pp.426-434
• /
• 2001

The hermetic reciprocating compressor driven by the BLDC motor rotating with variable speeds, is modelled and analyzed for dynamic characteristics. The governing equations of piston, connecting rod and crank-shaft of the reciprocating compression mechanism and characteristics of driving torque of the motor are obtained. Dynamic behavior of the crankshaft supported on 2 journal bearings is analyzed considering compression load and eccentric unbalance for the 4 rotating speeds of crankshaft. And. reaction forces generated from oil film in the journal bearings are analyzed under transient condition using Reynolds' equation. To take into account the dynamic characteristics depending on the variable rotating speeds, comparison on the dynamic behavior of crank-shaft is made for the 4 operating modes of the compressor. Results show that the magnitude of crankshaft locioperating on the lower rotating speeds is more larger than the higher ones due to reduction of inertia force of the reciprocating piston.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1988년도 전기.전자공학 학술대회 논문집
• /
• pp.93-97
• /
• 1988

The sliding mode control is an effective method to establish robustness against parameter variations and disturbance. But, in sliding mode strategy, the control function is discontinuous on the hyperplane. Consequently, the control input chatters at high frequency. When we apply such a control to the induction motor drive system, that causes a torque ripple and current harmonics, which are harmful to the system. In this paper, we introduce a low pass filter between sliding mode control output and driver input to overcome that problem. The band-width of this filter is varied according to the error funtion to improve transient responses.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2001년도 춘계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.147-149
• /
• 2001

The single-phase line-start permanent magnet motor has been shown to be capable of very desirable steady state performance, but known to have undesirable starting performance. This is because magnetic braking torque. So, it is very important to predict starting performance accurately when designing the line-start motors. In this paper, starting performance was calculated by combination of d-q axis voltage equations and mechanical dynamic equations. D-q axis voltage components were derived by winding angle and turns ratio transformations.

• 대한전기학회논문지
• /
• 제40권2호
• /
• pp.200-206
• /
• 1991

In this paper, an output feedback is used to reduce the effect of the vibration in the control of a flexible one-link robot arm. A PD control method with a time varying gain is proposed to improve the performance of the system in tip deflection and settling time for the step reference input. By making the change of feedback gain smoothly, th input torque can be made smooth. When there is a payload with unknown mass, an interpolation method which uses the inrehgrated value of the transient response of the hub angle is proposed for the estimation of teh payload mass. This method can be used when the reference input is known and we can get highly accurate estimate for the unknown payload. It is also demonstrated that flexible one-link arm can be controlled prettry accurately by an output feedback in a noisy environment without knowing the mass of the payload.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2004년도 하계학술대회 논문집 B
• /
• pp.1007-1009
• /
• 2004

This paper describes the design and the performance analysis of high speed induction motor considering end-ring using F.E.M.. To investigate the flux distribution, the induced rotor current, the designed high speed induction motor is analyzed by 3-D F.E.M.. Also, to identify the design specification, the performance characteristic is analyzed and estimated into the torque, the current and the output power at the static and the transient state.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2007년도 제38회 하계학술대회
• /
• pp.1039-1040
• /
• 2007

This paper is derived a solutions for an analytical model of an induction motor and the formula of regenerative power, based on spiral vector. The torque is controlled linearity through variations of the slip angular velocity, based on the field acceleration method (FAM). And also PWM inverter fed induction motor drives is schemed to be easily a regenerative power. The experimental tests verify the performance of the FAM, proving that good behavior of the drive is achieved in the transient and steady state operating condition. and are discussed to shave the power that regenerative power is measured at the operating acceleration or deceleration of servo system.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2004년도 하계학술대회 논문집 A
• /
• pp.304-306
• /
• 2004

Recently, operating equipment with the high quality is necessary as technology is developing rapidly and equipment becomes more accurate. Therefore, the importance of diagnosis has been rising in modem industries. This paper presents that the induction motor is driven by invertor. We were using EMTP (Electromagnetic Transient Program) to study different characteristics of induction motor caused by faults; single phasing and the short circuit fault. After having the fault occurred in feeder cable, motor current, flux and torque waveform are analyzed

• Journal of Power Electronics
• /
• 제5권2호
• /
• pp.151-159
• /
• 2005

The errors generated from current measurement paths are inevitable, and they can be divided into two categories: offset error and scaling error. The current data including these errors cause periodic speed ripples which are one and two times the stator electrical frequency respectively. Since these undesirable ripples bring about harmful influences to motor driving systems, a compensation algorithm must be introduced to the control algorithm of the motor drive. In this paper, a new compensation algorithm is proposed. The signal of the integrator output of the d-axis current regulator is chosen and processed to compensate for the current measurement errors. Usually the d-axis current command is zero or constant to acquire the maximum torque or unity power factor in the ac drive system, and the output of the d-axis current regulator is nearly zero or constant as well. If the stator currents include the offset and scaling errors, the respective motor speed produces a ripple related to one and two times the stator electrical frequency, and the signal of the integrator output of the d-axis current regulator also produces the ripple as the motor speed does. The compensation of the current measurement errors is easily implemented to smooth the signal of the integrator output of the d-axis current regulator by subtracting the DC offset value or rescaling the gain of the hall sensor. Therefore, the proposed algorithm has several features: the robustness in the variation of the mechanical parameters, the application of the steady and transient state, the ease of implementation, and less computation time. The MATLAB simulation and experimental results are shown in order to verify the validity of the proposed current compensating algorithm.