• Journal of Advanced Marine Engineering and Technology
• /
• 제20권1호
• /
• pp.44-48
• /
• 1996

In manufacturing of exact products, the offsetting is required to transfer the design data of shape to manufacturing data. In offsetting the degeneracies are occurred, and these problems are mere difficult in freeform shapr manufacuring. This paper is using the geometric properties of B-spline curves to solve the degeneracy of offsetting and to generating of enhanced offsetting. The offsetting of B-spline control polygon spans generates exact control polygon of original shapes. This method is faster in generating offset curve than the normal offsetting, and the resulted offset curves are exact. The additional property of this method is using to control offset shape as B-spline curves. We believe that this method is as effective solution for modifying of offset curves.

• 수산해양기술연구
• /
• 제27권4호
• /
• pp.321-327
• /
• 1991

Experiments of quenching were made with cylindrical specimens of carbon steel S45C of diameters from 12 to 30mm were performed. The specimens were heated by electric furnace and quenched by immersion method. In order to analyze the temperature profile(cooling curves) of carbon steel including the latent heat of phase transformation, nonlinear heat conduction problem was calculated by the numerical method of inverse heat conduction problem using the apparent heat capacity method. The difference between the calculated and the experimented cooling curves was caused by the latent heat of phase transformation, and the effects of the latent heat were especially manifest at the cooling curves of center of specimens. The temperature and the quantity of the latent heat of phase transformation depend on the cooling speed at A sub(1) transformation point, and the region for cooling speed to become zero was caused by the latent heat of phase transformation.

• 천문학회지
• /
• 제39권1호
• /
• pp.25-30
• /
• 2006

We completed four color light curves of the near-contact binary CN And during three nights from September to December 2004 using the 61-cm reflector and BV RI filters at Sobaeksan Observatory. We determined four new times of minimum light (two timings for primary eclipse, two for secondary). Newly obtained BV RI light curves and the radial velocity curves from Rucinski et a1. (2000) were simultaneously analyzed to derive the system parameters of CN And. We used the semi-detached mode 4 of the 2003-version of the Wilson-Devinney binary model, and interpreted the asymmetry of the light curve by introducing two spots; a cool spot on the primary component and a hot spot on the secondary component. New photometric parameters are not much different from those of Cicek et a1. (2005), and it is considered that the system is in the era of broken contact. From the orbital period study with all available timings including our data, we found a continous period decrease with a rate of $P_{obs}=--1.82{\times}10^{-7}\;d\;yr^{-1}$ that can be explained with two possible mechanisms. We think the most likely cause of the period decrease is a thermal mass transfer from the primary to the secondary component, rather than angular momentum loss due to a magnetic stellar wind.

• Journal of Advanced Marine Engineering and Technology
• /
• 제19권2호
• /
• pp.20-26
• /
• 1995

The very rapid cooling problem from $820^{\circ}$C to $20^{\circ}$C on the surface of the steel by thermal conduction including the latent heat of phase transformation of steel and by transient boiling heat transfer of water are considered to principal problem in quenching. The transient boiling process of water at the surface of specimen during the quenching process were experimentally analyzed. Then the heat flux was numerically calculated by the numerical method of inverse heat condition problem. In this report, the simulation program to calculate the cooling curves for large rolls was made using the subcooled transient boiling curve as a boundary condition. By this simulation program, the cooling curves of rolls from D=50mm to D=200mm were calculated and the effects of agitation of circulation of water also investigated.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 1996년도 가을 학술발표회 논문집
• /
• pp.337-344
• /
• 1996

• 대한기계학회논문집A
• /
• 제26권10호
• /
• pp.2104-2113
• /
• 2002

A finite element model is developed for the process of squeeze casting of metal matrix composites (MMCs) in cylindrical molds. The fluid flow and the heat transit. are fundamental phenomena in squeeze casting. To describe heat transfer in the solidification of molten aluminum, the energy equation is written in terms of temperature and enthalpy are applied in an axisymmetric model which is similar to the experimental system. A one dimensional flow model simulates the transient metal flow. A direct iteration technique was used to solve the resulting nonlinear algebraic equations, using a computer program to calculate the enthalpy, temperature and fluid velocity. The cooling curves and temperature distribution during infiltration and solidification were calculated fer pure aluminum. Experimentally, the temperature was measured and recorded using thermocouple wire. The measured time-temperature data were compared with the calculated cooling curves. The resulting agreement shows that the finite element model can accurately estimate the solidification time and predict the cooling process.

• Steel and Composite Structures
• /
• 제21권1호
• /
• pp.157-175
• /
• 2016

It was found that the lateral stiffness changes obvious at the transfer position of the section configuration from SRC to RC. This particular behavior leads to that the transfer columns become as the important elements in SRC-RC hybrid structures. A comprehensive study was conducted to investigate the seismic behavior of SRC-RC transfer columns based on a low cyclic loading test of 16 transfer columns compared with 1 RC column. Test results shows three failure modes for transfer columns, which are shear failure, bond failure and bend failure. Its seismic behavior was completely analyzed about the failure mode, hysteretic and skeleton curves, bearing capacity deformation ability, stiffness degradation and energy dissipation. It is further determined that displacement ductility coefficient of transfer columns changes from 1.97 to 5.99. The stiffness of transfer columns are at the interval of SRC and RC, and hence transfer columns can play the role of transition from SRC to RC. All specimens show similar discipline of stiffness degradation and the process can be divided into three parts. Some specimens of transfer column lose bearing capacity swiftly after shear cracking and showed weak energy dissipation ability, but the others show better ability of energy dissipation than RC column.

• 설비공학논문집
• /
• 제3권1호
• /
• pp.51-60
• /
• 1991

The aim of this study is to investigate the heat transfer characteristics in the transient cooling process of a high temperature wall. The slow transient cooling experiment was carried out with a copper block of high thermal capacity. The results of these experiments are as follows. 1. Temperature histories measured by the thermocouple, which is 0.99, 2.00, 2.99mm from the heat transfer surface showed monotonous during the cooling process. These variation are the curves of typical temperature histories in film-boiling, transition-boiling, and nucleate-boiling regions. 2. The temperature histories were measured by thermocouple installed in the copper block. The variations of the surface heat fluxes and surface temperature were computed from the numerical solution method TDMA from the measured temperature histories for radial position one dimensional heat transfer inverse problem. The boiling curves were found by the computed temperature histories. 3. The rewetting point which starts to change from film boiling to nucleate boiling is not connected with the mass velocity and it were found that the temperature of rewetting point indicated about $100^{\circ}C$. 4. The heat flux of rewetting point was about $10^5Kcal/m^2h$, at that time, the heat transfer coeficient indicated about $1000Kcal/m^2h^{\circ}C$ irrelevent to mass velocity. 5. The wall superheat decreases as the pressure increases. But I found that rewetting point appeared under higher condition in the wall temperature.

• Journal of Electrochemical Science and Technology
• /
• 제3권4호
• /
• pp.165-171
• /
• 2012

An experimental study of mass transfer to an amalgamated copper rotating disc electrode has been employed to determine an empirical correlation for the mass transfer rate in laminar flow. The study was performed in a three-electrodes configuration using 0.1 M boric acid and 0.1M potassium chloride as supporting electrolyte with Zn (II) concentration in the range (25-100 mg $dm^{-3}$). Polarization curves at different zinc ion concentration are reported. Hydrogen and oxygen reduction has also been considered.The diffusion coefficients and mass transfer coefficient were obtained using limiting diffusion current technique based on zinc ion reduction. A least squares analysis indicates that the laminar flow results for 13067 < Re > 57552 and 550 < Sc > 1390 can be correlated by the following equation with correlation coefficient (CR) equal to 0.98: $sh=0.61Re^{0.5}Sc^{1/3}$.

• 반도체디스플레이기술학회지
• /
• 제11권1호
• /
• pp.35-39
• /
• 2012

$YAlO_3:Tb{_x}^{3+}$ has been synthesized by a combustion process and the concentration x of Tb was varied from 0.001 and 0.05 mol% per mole of $YAlO_3$. The emission optical properties on the $YAlO_3:Tb{_x}^{3+}$ have been investigated by time-resolved photoluminescence spectra and decay curves of center wavelength. The emission color changes from blue to green with increasing the $Tb^{3+}$ concentration from x= 0.001 to 0.05 mole fraction in $YAlO_3$ host. This emission color change can be explained in terms of cross-relaxation processes. Decay curves of emission intensity indicate that the type of energy transfer is donor-acceptor transition.