• Proceedings of the KSR Conference
• /
• 2002.10b
• /
• pp.1035-1040
• /
• 2002

Railway plate girder bridges have characteristics that are not show dominant frequency in dynamic response frequencies like obtained vertical acceleration on the bridge during the train passing because the train loading relatively bigger than the bridge self-weight. This paper experimentally confirmed in FFT result has various frequencies due to inherent characteristic of railway train loading. To establish classification of dynamic frequency range in railway bridge acceleration during the train passing, vibration frequencies result from experimental test are analyzed concerning actuation vibration factors. Factors are train velocity, train type, mass ratio of vehicle/bridge, stiffness of bridge, bridge/track and vehicle/track. From the result, it is proposed that the frequencty classfication table with corresponding factors. Using the proposed table to develop rehabilitation technique of the plate girder bridge, to expect vibration reduction and comfort enhancement of the railway plate girder bridge.

• Proceedings of the KSR Conference
• /
• 1998.11a
• /
• pp.194-201
• /
• 1998

It is extremely necessary to use such a secure way to transmit information to a train, which is needed for operating a train. In our system, The information including the allowable velocity of the train, train existence in current area, and other data necessary for operating train, is transmitted in the form of FM signal. Received by the receiver located on train, the signal is filtered, demodulated and analyzed to extract the original information. The analysis of the demodulated signal is done through FFT algorithm using sliding slot. These all are processed digitally by hardware which is implemented by 32bit DSP. The experiments show the validity of the algorithm we presented.

• Particle and aerosol research
• /
• v.11 no.1
• /
• pp.21-28
• /
• 2015

In this study, the flow around a subway train running in an underground tunnel was numerically estimated. For the validation of the numerical results, the airflow velocity at a point underneath a subway train was measured using an ultrasonic anemometer. Then, the trajectories of particles generated at the contact points between the wheels and rails were numerically predicted. By considering the airflow velocity and particle trajectories, the space underneath the T-Car (trailer car) was expected to be appropriate for the room for the installation of a dust-removal system.

• Journal of the Korean Society for Precision Engineering
• /
• v.29 no.7
• /
• pp.770-777
• /
• 2012

This paper deals with the design and modal characteristics analysis of a drive-train for a paralleltype hybrid electric vehicle (HEV). The function of the drive-train system (DTS) in the HEV combines or divides the torque and velocity from the internal combustion engine along with the induction motor. The system consists of a compound planetary gear and unit's electromagnetic clutch to provide the operation modes such as Engine Only (EO), Electric Vehicle (EV), and Hybrid Electric Vehicle (HEV) modes. In order to investigate the characteristics of the velocity and torque flow for the system, dynamic models of the HEV with DTS are derived from the prototype DTS. The performance of the derived dynamic models is evaluated by both computer simulations and experiments according to each mode.

• Journal of the Korean Society of Safety
• /
• v.23 no.4
• /
• pp.1-6
• /
• 2008

This experiments are perfol1ned to investigate the effect of ventilation velocity on a high pressure water mist tire suppression in train. The experiment is conducted in half scale modeled train of a steel-welled enclosure (5.0m${\times}$2.4m${\times}$2.2m). The ventilation velocity is controlled by the ventilation duct through an inverter in the range of 0 to 3m/s. The coverage-radius and an injection angle of an high pressure water mist system are measured. The mist nozzle with 5-injection holes is operated with pressure 60bar. The heptane pool fires are used. The fire extinguishment times and the temperature are measured for the ventilation velocities. In conclusion, because the momentum of injected water mist is more dominant than that of ventilation air, the characteristics of water mist, the fire extinguishment times and the temperature are affected very little by ventilation velocity.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.10
• /
• pp.681-687
• /
• 2017

We investigated the potential for wind-power generation using the wind produced by express trains. We built equipment to detect the wind velocity, including wind meters and a data analyzer. We considered various conditions that might change the wind. First, we measured the velocity and duration of the wind at three locations distinguished by the presence of a tunnel and a valley landscape. We analyzed the changes in the wind according to the geometric conditions. Also, we analyzed the changes in the wind according to three different heights relative to the train. We also compared the wind produced by a KTX train and an SRT train. Finally, we used the results to derive the wind power energy harvested from the wind and discuss the expected utility.

• Journal of Advanced Marine Engineering and Technology
• /
• v.35 no.1
• /
• pp.108-117
• /
• 2011

Old train carriages have been used to create artificial reefs (AR) as part of programs to enhance ocean fisheries and recreational resources. This study conducted hydraulic modeling experiments to estimate the structural stability of a train carriage AR. By applying fixed- and movable-bed conditions and Froude similitude, theoretical and hydraulic experiments revealed major design forces(e.g., water waves and currents). The results of this study showed that some dimensionless design parameters (e.g., surf similarity parameters, water particle velocity, scouring, and deposition) also affect the stability of an AR under various wave and current field conditions. In the fixed-bed condition, movement of the AR occurred when dimensionless water particle velocity based on the surf similarity parameter was larger than about 0.32. In the moveable-bed condition, the settlement depth (field values) of the AR ranged from 6 to 30 cm. The results indicated that characteristics of the sediment/bed condition and the direction of external forces acting on an AR should be considered when selecting AR sites.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.52 no.5
• /
• pp.197-202
• /
• 2003

When a high-speed train reduces its operating velocity while decelerating from a maximum of 350 to 50 [km/h], the train applies eddy-current brakes, which results in a deceleration time of approximately 3minutes. Therefore, a high current is utilized in order to obtain a large braking force. Consequently, the temperature of the electromagnet and rail increases significantly. In this paper, The thermal characteristics on a single magnet pole with convection heat transfer coefficient are simulated by using 2D-FEM. To verify the analysis results, the computed temperatures are compared with the experimentally measured temperature at stationary state. Furthermore, transient-state thermal analysis is performed to predict the magnet temperatures as the train is decelerating.

• Proceedings of the KIEE Conference
• /
• 2003.04a
• /
• pp.432-434
• /
• 2003

The korean high speed train(350km/h), composed of 7cars that are 2 power cars, 2 motorized car and 3 trailer cars, has been developed and is under on-line test. To verify the design requirements about the functions and traction performances of this train, KRRI(Korea Railroad Research Institute) decided to evaluate traction performances of the train during on-line test. For this purpose, such as torque, velocity, voltage and current, must be measured. KRRI has developed the measurement system that can be measured vast and various signals effectively. In this paper, we introduce traction performances of korean high speed train. The traction measurement items are focused on the verification of motor block performances.

• 한국전산유체공학회:학술대회논문집
• /
• 2000.05a
• /
• pp.91-98
• /
• 2000

The three-dimensional unsteady compressible Full Navier-Stokes equation solver with sliding multi-block method has been applied to analyze three dimensional characteristics of the flow field and compression wave around the high speed train which Is entering into a tunnel. The numerical scheme of AF + ADI was used to efficiently solve Navier-Stokes equations in the curvilinear coordinate system. The vortex formation around the nose region was found and the generation of compression wave due to the blockage effects was observed ahead of the train in the form of plane wave. The three dimensional characteristics of the flow field compared to the analytic results were discussed in detail. The variation of pressure of tunnel wall surface and velocity profile of the train are identified as the train enters into a tunnel. The changes in aerodynamic forces and streamlines of each specific sections are also discussed and presented.