• Journal of the Society of Naval Architects of Korea
• /
• v.51 no.1
• /
• pp.8-15
• /
• 2014

In this study, flow characteristics around the hull form of KLNG are investigated by numerical simulations. The numerical simulations of the turbulent flows with the free surface around KLNG have been carried out at Froude number 0.1964 using the FLUENT 6.3 solver with Reynolds stress turbulence model. Several GEOSIM models are adopted to consider the scale effect attendant on Reynolds number. Furthermore, a full scale ship is calculated and the result is compared with the numerical results of GEOSIM models. The calculated results of GEOSIM models and the full scale ship are compared with the experiment data of MOERI towing tank test and Inha university towing tank test. Moreover, wake distribution on the propeller plane of the full scale ship is estimated using the numerical results of GEOSIM models. The prediction result is directly compared with the simulation result in full scale.

• Journal of Ocean Engineering and Technology
• /
• v.23 no.4
• /
• pp.38-46
• /
• 2009

Two sets of numerical simulations were carried out for a planing hull model ship. In the first, the WAVIS 1.4 linear and nonlinear potential solver was utilized with the free support condition, in which the running posture was determined during calculation. The linear and nonlinear potential calculation results showed qualitative agreement in the trim and resistance coefficient with the MOERI towing tank test. However, the nonlinear potential calculation gave better results than the linear method. In the next simulation, Fluent 6.3.26 with a VOF model and the WAVIS 1.4 nonlinear potential solver were used with the given running posture from the measurement carried out in the MOERI towing tank. Fluent with the VOF method had substantially better agreement with model test results than the results from the WAVIS nonlinear potential calculation for the total resistance coefficient, and for the bow and stern wave patterns, in spite of the much greater computational costs. Both methods can be utilized in planing hull design when their limitations are perceived, and the running posture should be predicted correctly.

• 한국기계연구소 소보
• /
• s.10
• /
• pp.63-77
• /
• 1983

This paper presents the hydrodynamic performance characteristics of a planing boat which was tested with a new dynamometer system specifically designed to measure towing force along the thrust plane, the change in trim angle and the vertical displacement of the model center of gravity from still water condition. The test conditions include systematic variations in the three positions of LCG and the three load coefficients of a high speed planing boat.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.23 no.5
• /
• pp.595-602
• /
• 2017

In Korea, much research and development have occurred to enhance the technological competitiveness of tuna purse seining fisheries. Due to these efforts, fishing efficiency has been improved with the development of radar, sonar and global positioning systems for fish detection and revisions to the hull forms of tuna purse seiners. However, for skiff boats, net boats and speed boats, which are auxiliary working boats mounted on tuna purse seiners, technology has lagged behind relative to the modernization of the main vessel. In this study, the hull of an existing propeller-based net boat with steel wire net to protect tuna was changed to the hull of a water jet propulsion vehicle to reduce resistance and improve maneuverability. As a result, a prototype of a water jet propulsion option was produced according to the aluminum structure strength standards specified by the Ministry of Oceans and Fisheries, and safety was confirmed by performing a drop test. Moreover, through a sea trial test, an existing net boat was shown to have a speed of 12.0knots and a towing force of 2,545 kgf at 2,500 RPM. The prototype had a speed of 26.7 knots and a towing force of 2,011 kgf at 3,200 RPM, which satisfied the towing capacity standards of auxiliary working boats mounted on tuna purse seiners.

• Journal of Advanced Marine Engineering and Technology
• /
• v.38 no.10
• /
• pp.1217-1224
• /
• 2014

This paper provides a practical scaling method to solve an old problem for scaling and developing the speed and resistance of a model to full-scale submarine in fully submerged underwater test. In every experimental test in towing tank, water tunnel and wind tunnel, in the first step, the speed of a model should be scaled to the full-scale vessel (ship or submarine). In the second step, the obtained resistance of the model should be developed. For submarine, there are two modes of movement: surface and submerged mode. There is no matter in surface mode because, according to Froude's law, the ratio of speed of the model to the full-scale vessel is proportional to the square root of lengths (length of the model on the length of the vessel). This leads to a reasonable speed and is not so much for the model that is applicable in the laboratory. The main problem is in submerged mode (fully submerged) that there isn't surface wave effect and therefore, Froude's law couldn't be used. Reynold's similarity is actually impossible to implement because it leads to very high speeds of the model that is impossible in a laboratory and inside the water. According to Reynold's similarity, the ratio of speed of the model to the full-scale vessel is proportional to the ratio of the full-scale length to the model length that leads to a too high speed. This paper proves that there is no need for exact Reynold's similarity because after a special Reynolds, resistance coefficient remains constant. Therefore, there is not compulsion for high speeds of the model. For proving this finding, three groups of results are presented: two cases are based on CFD method, and one case is based on the model test in towing tank. All these three results are presented for three different shapes that can show; this finding is independent of the shapes and geometries. For CFD method, Flow Vision software has been used.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.31 no.4
• /
• pp.340-349
• /
• 1995

There are several problems in a fishing by the midwater pair trawl net which is used in Denmark; steeply decreasing of the net height with the towing speed increasing, the larger volume of the fishing gear in comparison with the size of the trawler, and catching of a float in a mesh, etc. To prevent steeply decreasing of the net height with the towing speed increasing and catching of a float in a mesh, it is sometimes more useful to use the kite instead of floats. This paper describes the hydrodynamic drag and the opening efficiency of the midwater pair trawl net and the midwater kite pair trawl net obtained by the model test in the circulation water channel. The results can be summarized as follows; 1. The hydrodynamic drag of the midwater kite pair trawl net is about 0.7 times smaller than that of the midwater pair trawl net. 2. The net height, mouth area and filtering volume of the midwater kite pair trawl net are smaller then those of the midwater pair trawl net when the towing speed is below 2.5knots, almost the same at 2.7knots, and are larger over 3.0knots. The net width of the midwater kite pair trawl net is same as that of the midwater pair trawl net. 3. The shapes of net mouth of both net are an oval steeply flatted with the towing speed increasing. The filtering volume of the midwater kite pair trawl net is larger then that of the midwater pair trawl net by 3% at 3.0knots, 11% at 4.0knots, and 16% at 5.0knots respectively.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.18 no.6
• /
• pp.591-596
• /
• 2012

Recently, a vessel's maneuvering performance is considered to be an important subject to secure safety at short sea shipping. Especially the high turning performance, which is required to avoid the marine pollution by the ships that was grounded, becomes more severe. In this paper, we discuss the effect of increasing rudder force on turning performance of short sea shipping ship by free running test in towing tank. First of all, we make the 47K PC model ship and high-lift rudder using Coanda effect. And we make the free running test system for the turning test in towing tank. And also we perform the turing test of 47K PC model in several changes of Coanda jet momentum and evaluate the turing performance such as advance and tactical diameter. Finally, we confirm that the increasing of rudder force is very effective to improvement of turning performance of short sea shipping ship.

• Journal of the Society of Naval Architects of Korea
• /
• v.46 no.5
• /
• pp.471-478
• /
• 2009

The present paper deals with characteristics of resistance performance according to the variation of synthetic ice thickness and hull form. The resistance test has been conducted with pack ice condition in Pusan National University towing tank. Stem angle has been chosen as main parameters for the variation of hull form characteristics, which is the most important factor especially in icebreaking cargo vessel. The serial comparisons of resistance test have been done with the variation of hull form parameter as well as with the different thickness of synthetic ice. The different trend of resistance performances with increasing of stem angle has been shown at each synthetic ice thickness. The present test results is expected to be confirmed by comparing the test results in ice tank in the near future.

• Journal of the Society of Naval Architects of Korea
• /
• v.51 no.4
• /
• pp.311-320
• /
• 2014

Test uncertainty of a towed underwater Stereoscopic Particle Image Velocimetry (SPIV) system was assessed in a towing tank. To estimate the systematic error and random error of mean velocity and turbulence properties measurement, velocity field of uniform flow was measured. Total uncertainty of the axial component of mean velocity was 1.45% of the uniform flow speed and total uncertainty of turbulence properties was 3.03%. Besides, variation of particle displacement was applied to identify the change of error distribution. In results for variation of particle displacement, the error rapidly increases with particle movement under one pixel. In addition, a nominal wake of a model ship was measured and compared with existing experimental data by five-hole Pitot tubes, Pitot-static tube, and hot wire anemometer. For mean velocity, small local vortex was identified with high spatial resolution of SPIV, but has serious disagreement in local maxima of turbulence properties due to limited sampling rate.

• Journal of the Society of Naval Architects of Korea
• /
• v.58 no.4
• /
• pp.243-252
• /
• 2021

The present study aims to investigate the interaction of a wire-type turbulence stimulator and the laminar boundary layer on a flat plate by flow field measurement. For the towing tank tests, a one-dimensional Laser Doppler Velocimetry (LDV) attached on a two-axis traverse was used to measure the streamwise velocity component of the boundary layer flow in zero pressure gradient, disturbed by a turbulence stimulator. The wire diameter was 0.5 and 1.0 mm according to the recommended procedures and guidelines suggested by the International Towing Tank Conference. Turbulence development by the stimulator was identified by the skin friction coefficient, mean and Root Mean Square (RMS) of the streamwise velocity. The laminar boundary layer with the absence of the wire-type stimulator was similar to the Blasius solution and previous experimental results. By the stimulator, the mean and RMS of the streamwise velocity were increased near the wall, showing typical features of the fully developed turbulent boundary layer. The critical Reynolds number was reduced from 2.7×10⁵ to 1.0×10⁵ by the disturbances caused by the wire. As the wire diameter and the roughness Reynolds number (Rek) increased, the disturbances by the stimulator increased RMS of the streamwise velocity than turbulent boundary layer.