• Structural Engineering and Mechanics
• /
• 제46권1호
• /
• pp.111-135
• /
• 2013

An experimental study has been carried out on square plain concrete (PC) and reinforced concrete (RC) columns strengthened with carbon fiber-reinforced polymer (CFRP) sheets. A total of 78 specimens were loaded to failure in axial compression and investigated in both axial and transverse directions. Slenderness of the columns, number of wrap layers and concrete strength were the test parameters. Compressive stress, axial and hoop strains were recorded to evaluate the stress-strain relationship, ultimate strength and ductility of the specimens. Results clearly demonstrate that composite wrapping can enhance the structural performance of square columns in terms of both maximum strength and ductility. On the basis of the effective lateral confining pressure of composite jacket and the effective FRP strain coefficient, new peak stress equations were proposed to predict the axial strength and corresponding strain of FRP-confined square concrete columns. This model incorporates the effect of the effective circumferential FRP failure strain and the effect of the effective lateral confining pressure. The results show that the predictions of the model agree well with the test data.

• 한국구조물진단유지관리공학회 논문집
• /
• 제24권6호
• /
• pp.25-33
• /
• 2020

취성재료의 변형률 분포와 인장물성과의 상관관계를 분석하기 위해 변형률 분포를 가지도록 탭부분을 변형한 5개 타입-S0, SD1, SD2, SV1, SV2 - 의 탄소섬유보강폴리머(CFRP) 인장시편군을 시험하였다. 변형률 분포가 큰 SD2, SV2 의 극한응력 및 변형률이 SD1, SV1 보다 작게 나타났는데, 이는 비대칭 형상의 SD타입보다 대칭 형상의 SV의 시험결과에서 더 분명하게 나타냈다. 더불어 본 연구에서 사용한 변형률 분포를 가진 대부분의 시편의 극한 응력 및 변형률은 변형률 분포가 없는 대조군과 비교하였을 때 감소하였다. 이러한 결과는 1) 변형률계를 통해 직접 계측한 변형률의 평균값, 2) 전체변형량을 유효길이로 나눠 산정하는 환산변형률, 3) 탄성계수와 극한하중으로부터 유도하는 (극한)유효변형률을 통해 다각적으로 분석되었다. 변형률계에서 계측된 값은 국소구간 응답을 정확히 나타내지만, 전단면의 응답을 표현하는 것은 아니다. 반면, 환산변형률과 유효변형률은 전단면의 평균거동을 나타내므로, 게이지의 단점을 보완할 수 있다. 특히 유효변형률은 극한하중 부근에서 변형률계 측정값이 게이지 손상이나 비정상적 계측값 등의 원인으로 유효하지 않을 때도 실무적으로도 사용할 있는 보수적인 파단변형률을 산정할 수 있다. 이 값은 부분파단이 발생한 경우에도 사용할 수 있으며, 변형률 분포를 가지는 시편에서 합리적으로 유용하다.

• 소성∙가공
• /
• 제32권5호
• /
• pp.239-246
• /
• 2023

To reduce the forming load due to the temperature drop, during the hot forging process, a reheating hot forging process design is required that to repeat heating and forging. However, if the critical strain required for recrystallization is not induced during forging and grain growth becomes dominant due to the reduction in dislocation density due to repeated heating, the mechanical properties may deteriorate. Therefore, in this study, Inconel 706 alloy was applied, and the grain refinement behavior was comparatively analyzed according to the number of reheating times and effective strain during reheating hot forging process. Reheating was carried out with a total compression rate of 40% up to 4 times. The Inconel 706 compression test specimens heated once showed finer grains as the effective strain increased due to the dynamic recrystallization phenomenon. However, as the number of heating increases, grain refinement was observed even in a low effective strain distribution of 0.43 due to static recrystallization during reheating. Moreover, grain growth occurs at a relatively low effective strain of 0.43 when the number of reheating is four or more. Therefore, it was effective to apply an effective strain of 0.43 or more during hot forging to Inconel 706 in order to induce crystallization through grain refinement and improve the properties of forged products. In addition, we could notice that up to three reheating times condition was appropriate to prevent grain growth and maintain fine grain size.

• 한국의류산업학회지
• /
• 제22권2호
• /
• pp.250-260
• /
• 2020

The purpose of the present study was to explore the most effective body region and cooling temperature to alleviate heat strain of workers in hot environments. We developed liquid cooling hood, vest, sleeves and socks and applied the water temperatures of 10, 15, 20, and 25℃ through the liquid cooling garments in a hot and humid environment (33℃ air temperature and 70% RH air humidity). A healthy young male participated in a total of 16 experimental trials (four cooling garments × four cooling temperatures) with the following protocol: 10-min rest, 40-min exercise on a treadmill and 10-min recovery. The results showed that rectal temperature, mean skin temperature, and ratings of perceived exertion during exercise; heart rate and diastolic blood pressure during recovery; and total sweat rate were lower for the vest condition than other garment conditions(p < .05). However, there was no differences in mean skin temperature among the four cooling garments when we compared the values converted by covering area(%BSA). When we classified the results by cooling temperature, there were no consistent differences in thermoregulatory and cardiovascular responses among the four temperatures, but 25℃ water temperature was evaluated as being the most ineffective cooling temperature in terms of subjective responses. In conclusion, the results indicated that wearing cooling vest with < 20℃ cooling temperature can alleviate heat strain of workers in hot and humid environments. If the peripheral body regions are cooled with liquid cooling garments, larger cooling area with lower cooling temperature than 10℃ would be effective to reduce heat strain of workers. Further studies with a vaild number of subjects are required.

• 한국정밀공학회지
• /
• 제12권3호
• /
• pp.42-52
• /
• 1995

An UBET(Upper Bound Elemental Techniquel) program has been developed to analyze forging load, die-cavity filling and effective strain distribution for flashless non-axisymmetric forging. To analyze the process easily, it is suggested that the deforma- tion is divided into two different parts. Those are axisymmetric part in corner and plane- strain part in lateral. The total power consumption is minimized through combination of two deformation parts by building block method, form which the upper-bound forging load, the flow pattern, the grid pattern, the velocity distribution and the effective strain are deter- mined. To show the merit of flashless forging, the results of flashless and flash-forging processes are compared through theory and experiment. Experiments have been carried out with plasticine billets at room temperature. The theoretical predictions of the forging load and the flow pattern are in good agrement with the experimental results.

• 한국환경보건학회지
• /
• 제24권3호
• /
• pp.70-76
• /
• 1998

Activation bacteria, identified from commercial microbial products, were applied to leachate treatment. Total seven strains of bacteria Enterobacteriaceae spp. (5), Bacillus sp. (1), Aeromonas sp. (1) were seeded in the leachate and cultured in the shaking incubator at 25$^{\circ}$C and 250 rpm. While cultured, they were sampled in given time intervals and the removal rates of SS, COD, BOD, T-N.and T-P were measured an indicators of leachate treatment. Through the screening test, four of 7 strains of bacteria were considered to be effective and they were named as "effective group". The capability of leachate treatment was observed on three different groups of bacteria single, effctive, and total mixed. The result showed that the removal rates of COD and SS for the total mixed group were 64 and 71% respectively. BOD removal rate was reached nearly 99% by seeding of effective griup and removal rates of T-P and T-N were 83 and 82% respectively. However seeding of single strain was less effective than that of any mixed group in leachate treatment.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1993년도 추계학술대회 논문집
• /
• pp.218-223
• /
• 1993

An UBET(Upper Bound Elemental Technique) program has been developed to analyze forging load, die-cavity filling and effective strain distribution for flashless forging. To analyze the process easily, it is suggested that the deformation is divided into two different parts. Those are axisymmetric part in corner and plane-strain part in lateral. The total power consumption is minimized through combination of two deformation parts by building block method, from which the upper-bound forging load, the flow pattern, the grid pattern, the veocity distribution and the effective strain are determined. To show the merit of flashless forging, the result of flashless and flash forging processes are compared through theory and experiment. Experiments have been carried out with plasticine billets at room temperature. The theoretical predictions of the forging load and the flow pattern are in good agreement with the experimental results.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1995년도 가을 학술발표회 논문집
• /
• pp.178-182
• /
• 1995

Strain localization is important phenomenon since it governs the total behavior or ultimate loads in various kinds of engineering problems. Establishment of an analysis method for strain localization phenomena is also of great concern for expansion of fracture mechanics of concrete. Inside zone of localization, a decrese in stress is accompanied by an increse in strain; outside the strain decreses. All deformation localization phenomenon cannot be predicted by both the classical stress-strain formulation and the linear elastic fracture mechanics. In this paper, a simple one dimensional model including localized deformation zone is studied under compressive and tensile loading. When the model is loaded. localization is assumed to occur uniformly in a finite region and material outside the localization zone is modelled as elastic unloading occurs. Size effects of effective elastic moduli under compression and tension in localization zone are examined.

• 한국구조물진단유지관리공학회 논문집
• /
• 제23권4호
• /
• pp.137-144
• /
• 2019

취성재료인 탄소섬유보강폴리머(CFRP)의 시편시험에서 총변형량과 유효길이로서 유도되는 환산변형률을 도입하고, 환산변형률의 장점을 기술하였다. 일반적으로 재료의 인장물성을 결정하기 위해 스트레인 게이지 측정값을 사용하지만, 취성특성을 가지는 CFRP에서는 항상 유효한 것은 아니다. 그 이유는 취성재료에서는 응력재분배를 할 수 없으며, 스트레인 게이지의 측정값은 국부거동만을 나타기 때문이다. 따라서 환산변형률은 취성재료의 인장인장특성의 평균값을 측정하고 변형률과 측정값을 검증하는 보조지표로서 효과적으로 사용될 수 있다. 또한 환산변형률은 1) 제작 오차(편차) 와 세팅 오차(정렬 불량)에 의해 발생하는 초기 내부 변형률에 기인한 영향과 2) 불균일 변형분포로 인한 부분파단 이후 거동을 명확히 가시화하는 장점이 있다.

• Journal of Nutrition and Health
• /
• 제31권2호
• /
• pp.143-152
• /
• 1998

This study was conducted to investigate the effects of chitosan, chitosan oligomer and beef tallow of different levels on lipid metabolism in rats, Seventy male rats of the Sprague-Dawley strain were blocked into 10 groups according to body weight , and were raised for 4 weeks. Dietary fat levels were 20% en and 40% en, and chitosan and chitosan oligomer were given at levels of 05, 3%, and 5%(wt/wt) of diet. The results are summarized as follows, chitosan oligomer supplement decreased serum total lipid, as chitosan 양, and exhibited a tendency to decrease serum total cholesterol. Chitosan oligomer supplement tended to increase the HDL cholesterol ; total cholesterol ration as chitosan did. Liver total lipid and triglyceride concentration were lower in high fat groups than in low fat groups. Liver total lipid concentrations was decreased slightly by chitosan and sigfnificantly by chitosna ligomer. Epididymal fat pad total lipid. total cholesterol and triglyceride concentration were slightly decreased by chitosan and chitosan oligomer supplement, especially in high fat groups. fat absorptivity was decreased by low fat level, chitisan and chitosan oligamer supplement. Fecal excretion of total lipid and triglyceride were increased by high fat level, chitosan and chi샌무 oligomer supplement. However, fecal excretion of total cholesterol was increased by high fat level and chitosan supplement. This indicated that chitosan and chitosan oligomer were effective in interfering with lipid and triglyceride absorption, In conclusion, chitosan oligomer at levels of 3% and 5% has more effective lipid, cholesterol and triglyceride lowering activity than chitosan.