• Special Issue of the Society of Naval Architects of Korea
• /
• 2013.12a
• /
• pp.81-84
• /
• 2013

일반적인 Bulk carrier는 Single deck, Double bottom, Hopper side tank, Top side tank와 함께 Single side skin 또는 Double side skin으로 구성되어 Single hull bulk carrier 또는 Double hull bulk carrier라 불린다. 본 논문의 연구선박인 Double hull bulk carrier는 CSR에서 규정짓고 있는 Double hull bulk carrier의 특징 중 Hopper side tank가 없기에 일반적인 Double hull bulk carrier와는 다른 구조를 가진다. 구조적 특징으로는 Inner bottom과 Inner hull 연결부위에 응력 집중 발생, Side shell의 Shear에 대해 구조적 안전성, Double hull에 대한 CSR for bulk carrier의 Rule적용 여부에 대한 판단 등이 있다. 따라서 본 연구에서는 Double hull bulk carrier의 구조적 특징과 구조해석을 통한 응력 집중 부위의 평가 및 Fatigue analysis을 통한 피로수명을 계산하여 이를 통해 구조의 안전성을 살펴보고자 한다.

• Proceedings of the KWS Conference
• /
• 2004.05a
• /
• pp.33-35
• /
• 2004

선박건조의 탑재공정에 있어서 용접장이 긴 후판 맞대기 용접에는 SAW가 대부분 적용되고 있지만 컨테이너 운반선의 UPPER DECK나 HATCH COAMING TOP PLATE 같은 경우 용접장이 짧고 작업공간이 협소하여 SAW가 적용되지 못하고 있다. (중략)

• Journal of the Korean Wood Science and Technology
• /
• v.48 no.5
• /
• pp.608-617
• /
• 2020

For efficient use and expansion of domestic small- and medium-diameter woods, cross-laminated wood panels composed of tropical hardwoods and domestic temperate woods were fabricated, and the bending creep behavior under long-term loading was investigated. The bending creep curve of the cross-laminated wood panels showed an exponential function graph with a sharp increase at the top right side. The wood panel composed of a teak top layer and larch core and bottom layers recorded the highest initial deformation, and that composed of a merbau top layer and tulip core and bottom layers showed the lowest initial deformation. Creep deformation of the cross-laminated wood panels showed the highest value in that composed of a teak top layer and larch core and bottom layers and showed the lowest value in that composed of a merbau top layer and tulip core and bottom layers. The obtained creep deformation is 3.1-4.3 times that of merbau, however, it is remarkably lower than that of tulip and larch. The highest relative creep was recorded by the wood panel composed of merbau top layer and larch core and bottom layers, whereas that composed of the teak top layer and tulip core and bottom layers showed the lowest relative creep.

• Korean journal of food and cookery science
• /
• v.29 no.2
• /
• pp.169-175
• /
• 2013

The purpose of this study was to provide the basic information necessary to efficiently run a coffee shop. It comparatively analyzes the relative importance and satisfaction of side menu selection characteristics through analyses on customer importance-satisfaction when selecting a side menu as well as their usage behavior of the side menu at coffee shops. According to reason price the analysis result on the differences in the coffee shop side menu importance and satisfaction, there was a difference because the importance of selecting a side menu was higher for the attributes of taste, health, packing & appearance, economics and personnel service compared to satisfaction among which the price of a side menu was found to be the top priority for improvement. The significance of coffee shop side menu for the respondents prior to usage as well as their satisfaction after usage was evaluated in order to comparatively analyze the relative importance and achievement of each characteristic through the IPA. The result indicated that the variables positioned in the Concentrate Here area (II) were related to economic feasibility such as reasonable price, appropriate price of set menu, telecommunication company affiliated service and coupon usage and point accumulation. As for the Keep up the Good Work area (I), there were many variables regarding personnel service including taste of side menu, blending with coffee, clean packing, clean packaging, staff's side menu knowledge, staff's quick response, staff's politeness and staff's sincere response. As for the variables in the Low Priority area (III), health variables on health such as nutritional value, eco-friendly food materials and calories were observed.

• Journal of the Korean Society for Advanced Composite Structures
• /
• v.6 no.2
• /
• pp.105-117
• /
• 2015

The purpose of this study is to develop a new seismic resistant method by using precast concrete wall panels for existing low-rise, reinforced concrete beam-column buildings such as school buildings. Three quasi-static hysteresis loading tests were experimentally performed on one unreinforced beam-column specimen and two reinforced specimens with L-type precast wall panels. The results were analyzed to find that the specimen with anchored connection experienced shear failure, while the other specimen with steel plate connection principally manifested flexural failure. The ultimate strength of the specimens was determined to be the weaker of the shear strength of top connection and flexural strength at the critical section of precast panel. In this setup of L-type panel specimens, if a push loading is applied to the reinforced concrete column on one side and push the precast concrete panel, a pull loading from upper shear connection is to be applied to the other side of the top shear connection of precast panel. Since the composite flexural behavior of the two members govern the total behavior during the push loading process, the ultimate horizontal resistance of this specimen was not directly influenced by shear strength at the top connection of precast panel. However, the RC column and PC wall panel member mainly exhibited non-composite behavior during the pull loading process. The ultimate horizontal resistance was directly influenced by the shear strength of top connection because the pull loading from the beam applied directly to the upper shear connection. The analytical result for the internal shear resistance at the connection pursuant to the anchor shear design of ACI 318M-11 Appendix-D except for the equation to predict the concrete breakout failure strength at the concrete side, principally agreed with the experimental result based on the elastic analysis of Midas-Zen by using the largest loading from experiment.

• Journal of the Microelectronics and Packaging Society
• /
• v.7 no.2
• /
• pp.47-53
• /
• 2000

The fluxless wetting properties of TSM-coated glass substrate were evaluated by the wetting balance method. We could estimate the wettability of the TSM with new parameters obtained from the wetting balance test for one side-coated specimen. It was more effective in wetting to use Cu as a wetting layer and Au as a protection layer than to use Au itself as a wetting layer. The SnSb solder showed better wettability than SnAg, SnBi, and SnIn solders. The contact angle of the one side-coated glass substrate to the Pb-free solders could be calculated from the farce balance equation by measuring the static force and the tilt angle.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.6 no.5
• /
• pp.211-221
• /
• 1998

Thermal behavior on the cylinder block of a 4-cylinder, 4-stroke 2.0L SOHC gasoline engine was numerically and experimentally analyzed. The numerical calculation was performed using the finite element method. The cylinder block was modelled as a three dimensional finite element by considering its geometry. The physical domain was devided into hexahedron elements. 16 thermocouples were installed at points of 2mm inside from cylinder wall near top ring of piston in cylinder block, which points have suffered major thermal loads and suggested as proper measurement points for engine design by industrial engineers. Under full load and 9$0^{\circ}C$ coolant temperature condition, temperature behavior of cylinder block according to engine speed were analyzed. The results showed that temperature rose gradually to conform to a function of 2nd~4th order of engine speed at intake side, exhaust and siamese side, respectively. As engine load was changed from 100 to 50% by 25% step, temperature curve also conformed to 2nd~7th order function of engine speed. Temperature differences by load condition were similar among 100, 75% and 50%. Under full load and coolant temperature of 11$0^{\circ}C$, temperature behavior were also analyzed and the result also showed conformance to 2n d~7th order function of engine speed. Temperature curve was transferred in parallel upwards corresponding coolant temperature rise.

• 한국신재생에너지학회:학술대회논문집
• /
• 2006.11a
• /
• pp.188-192
• /
• 2006

This study is conducted to improve efficiency of thermal storage tank. The thermal storage tank was designed to store heat energy that obtained from solar or the others heat sources. However, it has difficulties in storing heat with uniform temperature through the entire tank with respect to vertical direction. This kind of maldistribution of the supplied heat to the storage tank effects on the system performance. In this study is focused on utilization of the thermal stratification to improve thermal comfort for people in the house. To enhance temperature stratification of the tank, a distributor was designed and Installed in the middle of the tank. The distributor is supplies hottest water to the top side of the tank which is very close to inlet of the supply line to the heating load. The hottest water that is accumulated on top side of the tank is firstly supplied to the load with higher temperature. Reminder water takes a little time to warming up until desired supply temperature reached. This kind alternating selection of the supply temperature is improve thermal comfort with moderated system performance.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.4 no.5
• /
• pp.1151-1156
• /
• 2000

In this paper, we report a fabrication of InP-based microstructurs for III-V compound semiconductor micromachining. Vertical liquid phase epitaxy(LPE) system was used in order to grow the InP/lnGaAsP/InP layers. The thicknesses of InP top-layer and InGaAsP were $1\mum \;and \;0.4\mum$, respectively. The fabrication of InGaAsP microstructures involves front-side bulk micromachining. The experimental result showed the beams must be carefully aligned in the <100> direction since the etching of the beam in the <100> direction is more faster than that of the beam in the <110> and <110> direction.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2000.05a
• /
• pp.447-450
• /
• 2000

In this paper, we report a fabrication of InP-based microstructurs for III-V compound semiconductor micromachining. Vertical liquid phase epitaxy(LPE) system was used in order to grow the Inp/InGaAsP/InP layers. The thicknesses of InP top-layer and InGaAsP were 1$\mu\textrm{m}$ and 0.4$\mu\textrm{m}$ respectively. The fabrication of InGaAsP microstructures involves front side bulk micromachining. The experimental result showed the beams must be carefully aligned in the <110> direction since the lateral etching of the beam in the <110> direction is more faster than that of the beam in the <100> direction.