• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2010.11a
• /
• pp.609-610
• /
• 2010

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.20 no.3
• /
• pp.263-267
• /
• 2011

Ultrasonic metal welding can be used to weld different metals together safely and precisely, without solder, flux and special preparation. Ultrasonic metal welding machine consists of a power supply, a transducer, a booster and a horn. This paper designed the horn needed for Ultrasonic metal welding. The horn has to be designed and manufactured accurately, because measurements such as the shape, length, mass and etc. have effects on the resonant frequency and the vibration mode. The designed horn has the feature of 40,000Hz of nature frequency, and maximizes vibration range in the Tip by resonance in the frequency of ultrasonic wave machine. In this paper, we calculated and analyzed the natural frequency to find the optimal design of the horn that had the amplitude about $12{\mu}m$ by the modal analysis and harmonic analysis using ANSYS. And we analyzed FFT analysis of the manufactured horn.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2013.05a
• /
• pp.1149-1150
• /
• 2013

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.07a
• /
• pp.385-388
• /
• 2001

The cutting performance of a machine depends on the ability of the design of the acoustic horn to facilitate an increase in tool-tip vibration, allowing a significant amount of material to be removed. In this paper, three kinds of acoustic horns were designed and FEM was used to estimate displacement magnifications of horn tips. An optimization procedure for the profile has been followed to obtain maximum magnification, for higher rate of material removal and safe working stresses for the horn material.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.13 no.3
• /
• pp.53-60
• /
• 2004

We have developed and manufactured an experimental ultrasonic polishing machine with frequency of 20kHz at the power of vibration 1.7㎾ for effective ultrasonic polishing in processing of high hardness material. Design of the horn is performed by the FEM analysis. The following conclusions were empirically deduced through experimental results to clarify the major elements which affect the surface roughness during the ultrasonic process by following the experimental plans. The ultrasonic polishing machine has been developed in parts of structure part, ultrasonic generator, vibrator. We were able to process the high hardness material without difficulty as a result of ultrasonic polishing by utilizing the groove added step-type horn. Through analyzing by applying the experimental plans, the rotating speed of the horn was determined to be the major factor in influencing the surface roughness. In the case of ceramic, wafer, we were able to obtain good surface roughness when the feed rate and the ultrasonic output were higher. Because the load on slurry particle increases when the ultrasonic output is higher, the processed surface becomes worse in the case of optical glass.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.21 no.4
• /
• pp.613-618
• /
• 2012

The Ultrasonic metal welding is used in the solid-phase welding method at room temperature or low temperature state. In welding process, the high frequency vibration energy is delivered to the welding part under the constant pressure for welding. In this study, we aimed to design and manufacture a 40,000 Hz band horn through finite element analysis. By performing modal analysis and harmonic response analysis, the modal analysis result is that the horn frequency was 39,599Hz and the harmonic response result that the horn frequency was 39,533Hz. These results were similar. In order to observe the designed horn's performance, about 4,000 voltage data was obtained from a light sensor and was analyzed by FFT analysis using Origin Tool. The result RMS amplitude was approximately $8.5{\mu}m$ at 40,000Hz, and maximum amplitude was $12.3{\mu}m$. Using this manufactured horn along with an ultrasonic metal welder and tension tester, the weldability of Cu sheets was evaluated. The maximum tensile force was 66.53 N in the welding condition of 2.0 bar pressure, 60% amplitude, and 0.32 s welding time. In excessive welding conditions, it was revealed that weldability is influenced negatively.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.11 no.1
• /
• pp.76-81
• /
• 2012

Ultrasonic metal welding is one of the welding methods which welds metal by applying high frequency vibrational energy into specific area at constant pressure, avaliable in room temperature and low temperature. Ultrasonic metal welder is consisted of power supply, transducer, booster, and horn. Precise designing is required since each parts' shape, length and mass can affect driving frequency and vibration mode. This paper focused to horn design, its length L was set to 62mm by calculating vibration equation. By performing modal analysis with various shape variable b times integer, when length of b is 30mm the output was 39,599Hz at 10th mode. Also by performing harmonic response analysis, the frequency response result was 39,533Hz, which was similar to modal analysis result. In order to observe the designed horn's performance, about 4,000 voltage data was obtained from a light sensor and was analyzed by FFT analysis using Origin Tool. The result RMS amplitude was approximately 8.5${\mu}m$ at 40,000Hz, and maximum amplitude was 12.3${\mu}m$. Therefore, it was verified that the ultrasonic metal welding horn was optimally designed.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.23 no.1
• /
• pp.84-91
• /
• 2013

Ultrasonic flip-chip bonding needs a precise bonding tool which delivers ultrasonic energy into chip bumps effectively to use the selected resonance mode and frequency of the horn structure. The bonding tool is excited at the resonance frequency and the input and output ports should locate at the anti-nodal points of the resonance mode. In this study, we propose new design method with topology optimization for ultrasonic bonding tools. The SIMP(solid isotropic material with penalization) method is used to formulate topology optimization and OC(optimal criteria) algorithm is adopted for the update scheme. MAC(modal assurance criterion) tracking is used for the target frequency and mode. We fabricate two prototypes of ultrasonic tools which are based on 3D optimization models after reviewing 2D and 3D topology optimization results. The prototypes are satisfied with the ultrasonic frequency and vibration amplitude as the ultrasonic bonding tools.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2012.04a
• /
• pp.580-581
• /
• 2012

• Transactions of Materials Processing
• /
• v.21 no.2
• /
• pp.119-125
• /
• 2012

The present study addresses a direct patterning process on a plastic film using ultrasonic vibration energy. In this process, a tool horn containing micro-patterns is attached to an ultrasonic power supply, and is used with ultrasonic vibration to replicate micro-patterns on the surface of a plastic film. To improve the replication characteristics of the micro-patterns, the effect of the die shape of the ultrasonic patterning process was investigated with respect to the flow direction control. Finite element analyses were performed to predict the flow characteristics of the polymer with variations in die design parameters. Experiments were conducted using the optimally-designed die, from which it was possible to attain much improved pattern replication.