• International Journal of Naval Architecture and Ocean Engineering
• /
• 제5권3호
• /
• pp.414-430
• /
• 2013

This paper shows the study of preswirl duct as an effective energy saving devices that have been devised and reviewed to support the propeller performance, especially for the ship of VLCC with large block coefficients. From the bare hull wake measurements, typical upper/lower asymmetry of hull wake at the propeller disk was found. The 2 kinds of pre-swirl duct, Unconventional half circular duct and Conventional circular pre-swirl duct have been designed and reviewed to recover the loss of propeller running in that condition. The general function of the pre-swirl duct was set to work against this asymmetry of wake and generate pre-swirled flow into the propeller against the propeller rotating direction. The optimum self propulsion tests with various angle configurations were carried out and the best configuration was decided. Accordingly, cavitation test was carried out with best configuration of unconventional half circular duct. The blade surface and tip vortex cavitation behaved smoother when the duct was mounted. The hull pressure amplitudes reflected this difference, so the hull pressure amplitude with duct was smaller than that of without duct.

• 대한치과의사협회지
• /
• 제57권11호
• /
• pp.672-678
• /
• 2019

AIM: The purpose of this study was to evaluate and compare the torsional fracture resistances, cyclic fatigue resistance, and bending stiffness of two nickel-titanium (NiTi) rotary instruments made of different heat-treated alloy: Aurum Blue (heat-treated) and Aurum Pro (conventional). Methods: Forty-five Aurum Blue and Aurum Pro NiTi files were selected for the three mechanical tests (n=15). For the torsional resistance test, 3 mm file tip was fixed and the shaft was driven clockwise at 2 rpm until fracture occurred by using a customized device. Cyclic fatigue resistance was evaluated by rotating instruments in artificial canal with dynamic mode. Bending stiffness was tested by observation of the bending moment on attaining a 45° bend. The results were analyzed by student-t tests at a significance level of 95%. The fractured surface of each groups were examined under a scanning electron microscope (SEM). Results: Aurum Blue showed significantly higher toughness, ultimate strength, distortion angle, and number of cycles to failure than those of Aurum Pro (p < 0.05). However, Aurum Blue and Aurum Pro did not differ significantly in terms of bending stiffness. SEM showed typical topographic appearances of the cyclic fatigue and torsional fracture. Conclusions: Under the limitations of this study, heat-treated instruments showed higher flexibility and fracture resistances than conventional NiTi instruments.

• Journal of Advanced Marine Engineering and Technology
• /
• 제37권5호
• /
• pp.510-519
• /
• 2013

Urea-SCR시스템에 적용하기 위한 액막형 선회분사기의 분사압력변화에 따른 분무특성이 실험적으로 조사되었다. 실험에 사용된 노즐은 형상비 3.1을 갖는 단공 압력식 액막형 선회노즐이며, 노즐선단에 분사되는 유체에 선회류를 형성하기 위한 선회기가 설치되어 있다. 노즐의 분사량 조절은 PWM(pulse width modulation)기법에 의해 제어되었다. 분무의 발달과정은 2차원 PIV에 의해 가시화되었으며, 분무각 변화가 조사되었다. 분무액적의 속도 및 크기는 2차원 PDPA에 의해 상온 대기압 조건에서 측정되었다. 분무구조는 분사압력에 큰 영향을 받으며, SMD는 분사압력 증가에 따라 감소하며 선행연구자의 반실험적 결과와 유사한 경향을 보임을 알 수 있었다.

• 한국전산구조공학회논문집
• /
• 제27권1호
• /
• pp.17-26
• /
• 2014

본 논문은 MLS(Moving Least Squares) 차분법을 바탕으로 동적균열전파 해석을 수행하기 위한 알고리즘을 제시한다. MLS 차분법은 절점만으로 이루어진 수치모델을 사용하며, 이동최소제곱법을 이용하여 전개한 Taylor 다항식을 기초로 미분근사식을 유도하기 때문에, 요소망의 제약에서 완벽하게 벗어난 절점해석이 가능하다. 시간항을 포함하는 동적 평형방정식은 Newmark 방법으로 시간적분 하였다. 동적하중을 받는 균열이 전파할 때, 매 시간단계마다 절점모델을 재구성하지 않고 균열선단 주변에서 국부적인 수정을 통해 해석이 가능하다. 동적균열을 묘사하기 위해 가시한계법(visibility criterion)을 적용하였고, 동적 에너지해방률을 산정하여 균열의 진전유무와 그에 상응하는 진전방향을 결정하였다. 모드 I 상태와 혼합모드 상태에서 균열이 진전하는 현상을 모사하였고, 이론해와 Element-Free Galerkin법으로 계산한 결과와의 비교를 통해 개발된 알고리즘의 정확성과 안정성을 검증하였다.

• 항공우주기술
• /
• 제12권1호
• /
• pp.22-31
• /
• 2013

틸트로터 항공기인 스마트무인기의 회전익모드, 천이모드, 고정익 모드 비행시험을 수행하여 전체 비행영역에 대한 비행제어법칙 검증을 완료하였다. 회전익모드에서는 자동이륙과 자동착륙, 자동호버 비행 및 자동회귀모드 비행을 수행하였다. 천이모드에서는 틸트각 10도 간격으로 속도, 고도, 롤/방위 유지명령을 이용하여 상승, 하강, 좌선회 및 우선회 비행을 수행하고, 자율천이비행을 수행하였다. 회전익모드와 천이모드에서의 로터속도는 98%를 유지하였고, 고정익 모드 비행은 260 km/h 속도에서 로터 회전수를 82%로 감속하여 최대속도까지 점진적으로 영역확장비행을 수행하였다. 최종적으로 대기고도 3 km에서 최고속도 440 km/h까지 도달하였다. 본 논문에서는 스마트무인기의 전체 비행영역에 대해 비행영역 확장시험을 수행하는 동안 획득된 데이터의 분석결과를 제시하고, 규격서의 비행제어 요구조건과 비교하여 비행성이 요구성능을 만족함을 검증하였다.

• 한국항공우주학회지
• /
• 제40권12호
• /
• pp.1017-1024
• /
• 2012

깃끝단 후퇴각을 가지는 최신 터보프롭 항공기의 프로펠러 블레이드에 대한 공력설계 및 해석을 수행하였다. 프로펠러 형상 설계를 위한 익형은 HS1 계열을 적용하였다. 와류-깃요소 이론(Vortex-Blade element theory)을 기반으로 하고 최소에너지 손실 조건을 만족하는 Adkins의 방법을 적용하여 Conventional 프로펠러 블레이드에 대한 공력설계 및 성능해석을 하였다. 목표 항공기의 설계점에서 코드 길이와 피치각을 변경해 가며 프로펠러 형상을 생성하였다. Conventional 프로펠러 블레이드 형상 정보를 기반으로 코드 길이, 깃끝단 후퇴각을 수정 적용하여 최신 프로펠러를 설계하였다. 전산유체역학을 이용한 설계된 최신 프로펠러 공력특성 분석을 통하여 최신 프로펠러가 적절하게 설계되었음을 확인하였다.

• Journal of Power Electronics
• /
• 제15권4호
• /
• pp.1047-1053
• /
• 2015

A time-domain simulation tool to predict the dynamic power output of wind turbines in an offshore wind farm was developed in this study. A wind turbine model consisting of first or second order transfer functions of various wind turbine elements was combined with the Ainslie's eddy viscosity wake model to construct the simulation tool. The wind turbine model also includes an aerodynamic model that is a look up table of power and thrust coefficients with respect to the tip speed ratio and pitch angle of the wind turbine obtained by a commercial multi-body dynamics simulation tool. The wake model includes algorithms of superposition of multiple wakes and propagation based on Taylor's frozen turbulence assumption. Torque and pitch control algorithms were implemented in the simulation tool to perform max-Cp and power regulation control of the wind turbines. The simulation tool calculates wind speeds in the two-dimensional domain of the wind farm at the hub height of the wind turbines and yields power outputs from individual wind turbines. The NREL 5MW reference wind turbine was targeted as a wind turbine to obtain parameters for the simulation. To validate the simulation tool, a Danish offshore wind farm with 80 wind turbines was modelled and used to predict the power from the wind farm. A comparison of the prediction with the measured values available in literature showed that the results from the simulation program were fairly close to the measured results in literature except when the wind turbines are congruent with the wind direction.

• E2M - 전기 전자와 첨단 소재
• /
• 제10권6호
• /
• pp.519-527
• /
• 1997

The micro crack was occurred where the stress concentrated by the thermal stress which was induced during the cooling period after molding process or by the various reliability tests. In order to estimate the possibility of development from inside micro crack to outside fracture, the fracture toughness of EMC should be measured under the various applicable condition. But study was conducted very rarely for the above area. In order to provide a was to decide the fracture resistance of EMC (Epoxy Molding Compound) of plastic package which is produced by using transfer molding method, measuring fracture is studied. The specimens were made with various EMC material. The diverse combination of test conditions, such as different temperature, temperature /humidity conditions, different filler shapes, and post cure treatment, were tried to examine the effects of environmental condition on the fracture toughness. This study proposed a way which could improve the reliability of LOC(Lead On Chip) type package by comparing the measured $J_{IC}$ of EMC and the calculated J-integral value from FEM(Finite Element Method). The measured $K_{IC}$ value of EMC above glass transition temperature dropped sharply as the temperature increased. The $K_{IC}$ was observed to be higher before the post cure treatment than after the post cure treatment. The change of $J_{IC}$ was significant by time change. J-integral was calculated to have maximum value the angle of the direction of fracture at the lead tip was 0 degree in SOJ package and -30 degree in TSOP package. The results FEM simulation were well agreed with the results of measurement within 5% tolerance. The package crack was proved to be affected more by the structure than by the composing material of package. The structure and the composing material are the variables to reduce the package crack.ack.

• The Korean Journal of Pain
• /
• 제36권1호
• /
• pp.98-105
• /
• 2023

Background: Ultrasound-guided first sacral transforaminal epidural steroid injection (S1 TFESI) is a useful and easily applicable alternative to fluoroscopy or computed tomography (CT) in lumbosacral radiculopathy. When a needle approach is used, poor visualization of the needle tip reduces the accuracy of the procedure, increasing its difficulty. This study aimed to improve ultrasound-guided S1 TFESI by evaluating radiological S1 posterior foramen data obtained using three-dimensional CT (3D-CT). Methods: Axial 3D-CT images of the pelvis were retrospectively analyzed. The radiological measurements obtained from the images included 1st posterior sacral foramen depth (S1D, mm), 1st posterior sacral foramen width (S1W, mm), the angle of the 1st posterior sacral foramen (S1A, °), and 1st posterior sacral foramen distance (S1ds, mm). The relationship between the demographic factors and measured values were then analyzed. Results: A total of 632 patients (287 male and 345 female) were examined. The mean S1D values for males and females were 11.9 ± 1.9 mm and 10.6 ± 1.8 mm, respectively (P < 0.001); the mean S1A 28.2 ± 4.8° and 30.1 ± 4.9°, respectively (P < 0.001); and the mean S1ds, 24.1 ± 2.9 mm and 22.9 ± 2.6 mm, respectively (P < 0.001); however, the mean S1W values were not significantly different. Height was the only significant predictor of S1D (β = 0.318, P = 0.004). Conclusions: Ultrasound-guided S1 TFESI performance and safety may be improved with adjustment of needle insertion depth congruent with the patient's height.

• Computers and Concrete
• /
• 제32권2호
• /
• pp.217-232
• /
• 2023

Numerous studies have been performed on the behavior of pile foundations in cold regions. This study first attempted to employ artificial neural networks (ANN) to predict pile-bearing capacity focusing on pile data recorded primarily on cold regions. As the ANN technique has disadvantages such as finding global minima or slower convergence rates, this study in the second phase deals with the development of an ANN-based predictive model improved with an Elephant herding optimizer (EHO), Dragonfly Algorithm (DA), Genetic Algorithm (GA), and Evolution Strategy (ES) methods for predicting the piles' bearing capacity. The network inputs included the pile geometrical features, pile area (m²), pile length (m), internal friction angle along the pile body and pile tip (Ø°), and effective vertical stress. The MLP model pile's output was the ultimate bearing capacity. A sensitivity analysis was performed to determine the optimum parameters to select the best predictive model. A trial-and-error technique was also used to find the optimum network architecture and the number of hidden nodes. According to the results, there is a good consistency between the pile-bearing DA-MLP-predicted capacities and the measured bearing capacities. Based on the R2 and determination coefficient as 0.90364 and 0.8643 for testing and training datasets, respectively, it is suggested that the DA-MLP model can be effectively implemented with higher reliability, efficiency, and practicability to predict the bearing capacity of piles.