• 대한기계학회논문집A
• /
• 제24권1호
• /
• pp.69-78
• /
• 2000

The one-parameter singular expression for stresses and displacements near a crack tip has been widely thought to be sufficiently accurate over a reasonable re ion for any geometry and loading conditions. In many cases, however subsequent terms of the series expansion are quantitatively significant, and so we now consider the evaluation of such terms and their effect on the predicted crack growth direction. For this purpose the problem of a cracked orthotropic plate subjected to a biaxial load is analysed. It is assumed that the material is ideal homogeneous anisotropic. BY considering the effect of the load applied parallel to the plane of the crack, the distribution of stresses and displacements at the crack tip is reanalyzed. In order to determine values for the angle of initial crack extension we employ the normal stress ratio criterion.

• 대한기계학회논문집
• /
• 제17권9호
• /
• pp.2223-2233
• /
• 1993

An engineering method is suggested to calculate the applied load versus crack extension in the elastic-plastic fracture. The condition for an increment of crack extension is set by a critical increment of crack-up opening displacement(CTOD). The ratio of the CTOD increment to the incremental crack extention is a critical crack-tip opening angle(CTOA), assumed to be constant for a material of a given thickness. The Dugdale model of crack-tip deformation in an infinite plate is applied to the method, and a complete solution for crack extension and crack instability is obtained. For finite-size specimens of arbitrary geometry in general yielding, an approximate generalization of the Dugdale model is suggested so that the approximation approaches the small-scale yielding solution in a low applied load and the finite-element solution in a large applied load. Maximum load is calculated so that an applied load attains either a limit load on an unbroken ligament or a peak load during crack extension. The proposed method was applied to three-point bend specimens of a carbon steel SM45C in various sizes. Reasonable agreements are found between calculated maximum loads and experimental failure loads. Therefore, the method can be a viable alternative to the J-R curve approach in the elastic-plastic fracture analysis.

• 오토저널
• /
• 제13권2호
• /
• pp.42-49
• /
• 1991

This study is to investigate the dispersion characteristics of diesel fuel spray in the initial stage of the beginning of the injection under the condition of room temperature and atmospheric pressure. It is difficult to analyse that the diesel fuel spray in diesel engine has unsteady intermittent spray. So author installed a fuel accumulator and an electromagnetic controller in order to keep the constant fuel injection rate with the time variation. With this modified fuel injection system, spray tip penetration, spray angle and initial spray development process are investigated by instantaneous photographic method. The results obtained in this study are as follows : 1) The initial shape of injection of diesel fuel spray shows the form of non-disintegrated intact core, but the formation of ligaments increasingly grows as the time increases. It can also be shown that fine droplets become disintegrated out from the ligaments. 2) The slope of spray tip penetration was changed to two different tendencies with time. The transition point of the slope is shown at the time of around between 0.09 msec and 0.4 msec from the beginning of injection. This is transition time from non-disintegrated intact core to formation of ligaments.

• 대한조선학회논문집
• /
• 제44권2호
• /
• pp.111-118
• /
• 2007

In order to investigate the noise characteristics of the different caviation, noise measurements were carried out in a large cavitation tunnel of the Samsuug Ship Model Basin(SSMB). The noise measurements for a 3-dimensional hydrofoil were carried out at the angle of attack of $12^{\circ}$ and $16^{\circ}$ according to the decrease in cavitation number. It is exhibited that sound pressure level(SPL) increased sharply with cavitation inception. The frequency of the noise induced by sheet cavitation was higher than that of tip vortex cavitation in the phase of cavitation inception. Within the range of the high frequency, in the case of fully developed cavitation, sheet cavitation noise was significantly increased in sound pressure level compared with tip vortex cavitation noise. In this study, the noise characteristics of the different cavitation types were considered experimentally and would be utilized as a basis for the analysis of propeller cavitation noise.

• 대한기계학회논문집
• /
• 제7권2호
• /
• pp.161-167
• /
• 1983

In this study the phenomenon of cutting stress which arises on cutting tools and work pieces in cutting process is investigated by rake angle of cutting tools and feed for this measurement, P$_{s}$-1 (high modulus, photolastic Inc.) was used as a cutting tool, P$_{s}$-3 (medium modulus, photolastic Inc.) was used as work piece and reduction apparatus was attached to the head stock, and orthogonal cutting was adapted as a cutting method and transparent glass was used to block the strain in the orientation of thickness. The followings are the results of this study. (1) Photoelastic experimental equipments have made it possible to make dynamic measurement and analyze stress distribution in cutting tool and work piece surface which has hitherto been conducted only in static measurement and analyzing method. (2) The maximum stress arising at tools and work pieces in cutting process is on the tool edge tip, and the maximum stress arising on the tip of cutting tools is equal to that on the contacting area of work pieces in values. (3) The distributions of maximum shear stress on certain parts of the cutting tools and work pieces are as follows; for cutting tools, .alpha.=12.deg., .alpha.=0.deg., .alpha.=-12.deg. in order, and for work pieces, .alpha.=-12.deg., .alpha.=0.deg., .alpha.=12.deg. in opposite order.der.

• 한국자동차공학회논문집
• /
• 제15권5호
• /
• pp.30-37
• /
• 2007

Dimethyl Ether(DME) is an alternative fuel for diesel engine, it is renewable and offers potential reductions in emissions. This work was conducted to figure out the macroscopic behavior and the atomization characteristics of DME using a common-rail injection system. The macroscopic behavior was visualized with the spray visualization system composed of a Nd;YAG laser and an ICCD camera. The atomization characteristics were investigated in terms of axial mean velocity, Sauter mean diameter(SMD) and droplet distributions obtained from a phase Doppler particle analyzer(PDPA) system. In this study, it was revealed that the macroscopic behavior and the atomization characteristics of DME are similar compared with commercial diesel fuel. However, DME fuel has a shorter spray tip penetration and a small SMD due to the effect of evaporation characteristics.

• 항공우주기술
• /
• 제8권1호
• /
• pp.197-206
• /
• 2009

스마트 무인기의 공력특성을 향상시키기 위하여 주익에는 와류생성기(vortex generator), 주익의 끝단에는 유동펜스(flow fence)를 적용하였다. 와류생성기는 SUAV의 최대양력계수와 실속각을 지연시키는 효과가 있었지만 높은 항력증가를 초래하여, 결국에는 양항비가 줄어들었다. 이를 개선하기 위하여 L-형태와 높이가 3mm와 5mm인 와류생성기를 적용하였다. 유동펜스는 나셀 틸팅각이 증가함에 따라 나셀에서 발생하는 박리에 의하여 주익성능이 감소하는 현상을 방지하기 위하여 사용하였다. 두 가지 유동제어 장치를 사용함에 따라 스마트 무인기의 공력특성들이 어떻게 변화하였는지를 정리하였다.

• Journal of Mechanical Science and Technology
• /
• 제14권2호
• /
• pp.226-235
• /
• 2000

The performance prediction of an airfoil fan using a commerical code, STAR/CD, is verified by comparing the calculated results with measured performance data and velocity fields of an airfoil fan. The effects of inlet tip clearance on performance are investigated. The calculations overestimate the pressure rise performance by about 10-25 percent. However, the performance reduction due to tip clearance is well predicted by numerical simulations. Main source of performance decrease is not only the slip factor but also impeller efficiency. The reduction in performance is 12-16 percent for 1 percent gap of the diameter. The calculated reductions in impeller efficiency and slip factor are also linearly proportional to the gap size. The span-wise distributions of phase averaged velocity and pressure at the impeller exit are strongly influenced by the radial gap size. The radial component of velocity and the flow angle increase over the passsage as the gap increases. The slip factor decreases and the loss increases with the gap size. The high velocity of leakage jet affects the impeller inlet and passage flows. With a larger clearance, the main stream moves to the impeller hub side and high loss region extends from the shroud to the hub.

• Structural Engineering and Mechanics
• /
• 제5권3호
• /
• pp.257-268
• /
• 1997

The elastic deflections and Euler buckling loads are investigated for a class of tapered and initially curved cantilevered beams subjected to loading at the tip. The beam's width increases linearly and its depth decreases linearly with the distance from the fixed end to the tip. Unloaded, the beam forms a circular are perpendicular to the axis of bending. The beam's deflection responses, obtained by solving the differential equations in closed form, are presented in terms of four nondimensional system parameters: taper ratio ${\kappa}$, initial shape ratio ${\Delta}_0$, end load ratio f, and load angle ${\theta}$. Laboratory measurements of the Euler buckling loads for scale models of tapered initially straight, corrugated beams compared favorably with those computed from the present analysis. The results are applicable to future designs of the end structures of highway guardrails, which can be designed to give the appropriate balance between the capacity to deflect a nearly head-on vehicle back to its right-of-way and the capacity to buckle sufficiently that penetration of the vehicle may be averted.

• 한국분무공학회지
• /
• 제22권3호
• /
• pp.109-115
• /
• 2017

The aim of this study is to investigate the effect of physical properties of fuels on spray characteristics in the gasoline direct injection system. Injection rate, spray visualization, and spray pattern experiments were performed to analyze the spray characteristics of ethanol, gasoline, and ethanol/gasoline blends. We measured injection rate of each fuel via the Bosch method. The spray visualization experiment was also carried out at atmospheric pressure using a high-speed camera. Finally, the average of drop surface area per unit volume was measured using the optical patternator. The experimental results from Bosch method showed that peak injection rate increased when the volume fraction of ethanol increased. In addition, higher viscosity of ethanol than that of gasoline leads to longer injection delay. At the initial injection region before reaching 0.8 ms, the spray tip penetration becomes longer as increasing the volume fraction of ethanol, but reversely shorter after 0.8 ms. It was found that ethanol makes spray angle become larger. The surface area per unit volume of the drop was decreased as the distance from the injection tip or the concentration of the gasoline increased.