• International Journal of Naval Architecture and Ocean Engineering
• /
• v.11 no.1
• /
• pp.143-153
• /
• 2019

In this study, numerical simulations for the prediction of added resistance for KVLCC2 with varying wave steepness are performed using a Computational Fluid Dynamics (CFD) method and a 3-D linear potential method, and then the non-linearities of added resistance and ship motions are investigated in regular short and long waves. Firstly, grid convergence tests in short and long waves are carried out to establish an optimal mesh system for CFD simulations. Secondly, numerical simulations are performed to predict ship added resistance and vertical motion responses in short and long waves and the results are verified using the available experimental data. Finally, the non-linearities of added resistance and ship motions with unsteady wave patterns in the time domain are investigated with the increase in wave steepness in both short and long waves. The present systematic study demonstrates that the numerical results have a reasonable agreement with the experimental data and emphasizes the non-linearity in the prediction of the added resistance and the ship motions with the increasing wave steepness in short and long waves.

• Journal of Biomedical Engineering Research
• /
• v.21 no.4
• /
• pp.363-372
• /
• 2000

The present study investigated flow dynamics of a straight elastic blood vessel under sinusoidal flow conditions in order to understand influence of wall motion and impedance phase angle(time delay between pressure and flow waveforms) on wall shear stress distribution using computational fluid dynamics. For the straight elastic tube model considered in the our method of computation. The results showed that wall motion induced additional terms in the axial velocity profile and the pressure gradient. These additional terms due to wall motion reduced the amplitude of wall shear stress and also changed the mean wall shear stress. Te trend of the changes was very different depending on the impedance phase angle. As the wall shear stress increased. As the phase angle was reduced from 0$^{\circ}$to -90$^{\circ}$for ${\pm}$4% wall motion case, the mean wall shear stress decreased by 10.5% and the amplitude of wasll shear stress increased by 17.5%. Therefore, for hypertensive patients vulnerable state to atherosclerosis according to low and oscillatory shear stress theory.

• Korean Journal of Applied Biomechanics
• /
• v.25 no.2
• /
• pp.191-198
• /
• 2015

Objective : The purpose of this study was to conduct biomechanical analysis of varying backpack loads on the lower limb movements during downhill walking over $-20^{\circ}$ ramp. Method : Thirteen male university students (age: $23.5{\pm}2.1yrs$, height: $175.7{\pm}4.6cm$, weight: $651.9{\pm}55.5N$) who have no musculoskeletal disorder were recruited as the subjects. Each subject walked over $20^{\circ}$ ramp with four different backpack weights (0%, 10%, 20% and 30% of body weight) in random order at a speed of $1.0{\pm}0.1m/s$. Five digital camcorders and two force plates were used to obtain 3-d data and kinetics of the lower extremity. For each trial being analyzed, five critical instants were identified from the video recordings. Ground reaction force, loading rate, decay rate, and resultant joint moment of the ankle and the knee were determined by the inverse dynamics analysis. For each dependent variable, one-way ANOVA with repeated measures was used to determine whether there were significant differences among four different backpack weight conditions (p<.05). When a significant difference was found, post hoc analyses were performed using the contrast procedure. Results : The results of this study showed that the medio-lateral GRFs at RHC in 20% and 30% body weight were significantly greater than the corresponding value in 0% of body weight. A consistent increase in the vertical GRFs as backpack loads increased was observed. The valgus joint movement of the knee at RTO in 30% body weight was significantly greater than the corresponding values in 0% and 10% body weight. The increased valgus moment of 30% body weight observed in this phase was associated with decelerating and stabilizing effects on the knee joint. The results also showed that the extension and valgus joint moments of the knee were systematically affected by the backpack load during downhill walking. Conclusion : Since downhill walking while carrying heavy external loads in a backpack may lead to excessive knee joint moment, damage can occur to the joint structures such as joint capsule and ligaments. Therefore, excessive repetitions of downhill walking should be avoided if the lower extremity is subjected to abnormally high levels of load over an extended period of time.

• Smart Structures and Systems
• /
• v.18 no.6
• /
• pp.1169-1188
• /
• 2016

Real-time substructuring techniques are currently an advanced experimental method for testing large size specimens in the laboratory. In dynamic substructuring, the whole tested system is split into two linked parts, the part of particular interest or nonlinearity, which is tested physically, and the remanding part which is tested numerically. To achieve near-perfect synchronization of the interface response between the physical specimen and the numerical model, a good controller is needed to compensate for transfer system dynamics, nonlinearities, uncertainties and time-varying parameters within the physical substructures. This paper presents the substructuring approach and control performance of the linear and the adaptive controllers for testing the dynamic characteristics of soil-structure-interaction system (SSI). This is difficult to emulate as an entire system in the laboratory because of the size and power supply limitations of the experimental facilities. A modified linear substructuring controller (MLSC) is proposed to replace the linear substructuring controller (LSC).The MLSC doesn't require the accurate mathematical model of the physical structure that is required by the LSC. The effects of parameter identification errors of physical structure and the shaking table on the control performance of the MLSC are analysed. An adaptive controller was designed to compensate for the errors from the simplification of the physical model in the MLSC, and from parameter identification errors. Comparative simulation and experimental tests were then performed to evaluate the performance of the MLSC and the adaptive controller.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.10 no.2
• /
• pp.64-72
• /
• 1998

Dynamic response analysis is carried out for slender marine structures such as tensioned risers and tethers of tension leg platform, which are subjected to floating vessel motions as well as environmental forces arising from ocean waves. A mumerical analysis procedure is developed by using finite element model of the structural member. Dynamic analses are performed in the time domain for regular waves. Parameter studies are carried out to highlight the effects of surface vessel motions on the lateral dynamics of the structures. Example results of displacements, bending stresses are compared for various in water depth, environmental condition and vessel motion. Some instability conditions of the structures due to time-varying tension by vessel heave motion are discussed through the example analyses. As the results, the interaction between vessel surge and heave motions amplifies the total structural response of a riser. In the case of a tether, the effect of vessel heave motion during heavy storm is seemed to be quite significant to lateral response of the structure.

• Journal of Power Electronics
• /
• v.19 no.1
• /
• pp.190-200
• /
• 2019

The flyback converter, which can be regarded as a nonlinear time-varying system, has complex dynamics and nonlinear behaviors. These phenomena can affect the stability of the converter. To simplify the modeling process and retain the information of the output capacitor branch, a special sampled-data model of a peak current-mode (PCM) controlled flyback converter is established in this paper. Based on this, its dynamic behaviors are analyzed, which provides guidance for designing the circuit parameters of the converter. With the critical stability boundary equation derived by a Jacobian matrix, the stable operation range with a varied output capacitor, proportional coefficient of error the amplifier, input voltage, reference voltage and slope of the compensation ramp of a PCM controlled flyback converter are investigated in detail. Research results show that the duty ratio should be less than 0.5 for a PCM controlled flyback converter without ramp compensation to operate in a stable state. The stability regions in the parameter space between the output capacitor and the proportional coefficient of the error amplifier are enlarged by increasing the input voltage or by decreasing the reference voltage. Furthermore, the ramp compensation also can extend to the stable region. Finally, time-domain simulations and experimental results are presented to verify the theoretical analysis results.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.44 no.2
• /
• pp.1-14
• /
• 2021

It is highly challenging to measure the efficiency of electric vehicle charging stations (EVCSs) because factors affecting operational characteristics of EVCSs are time-varying in practice. For the efficiency measurement, environmental factors around the EVCSs can be considered because such factors affect charging behaviors of electric vehicle drivers, resulting in variations of accessibility and attractiveness for the EVCSs. Considering dynamics of the factors, this paper examines the technical efficiency of 622 electric vehicle charging stations in Seoul using data envelopment analysis (DEA). The DEA is formulated as a multi-period output-oriented constant return to scale model. Five inputs including floating population, number of nearby EVCSs, average distance of nearby EVCSs, traffic volume and traffic congestion are considered and the charging frequency of EVCSs is used as the output. The result of efficiency measurement shows that not many EVCSs has most of charging demand at certain periods of time, while the others are facing with anemic charging demand. Tobit regression analyses show that the traffic congestion negatively affects the efficiency of EVCSs, while the traffic volume and the number of nearby EVCSs are positive factors improving the efficiency around EVCSs. We draw some notable characteristics of efficient EVCSs by comparing means of the inputs related to the groups classified by K-means clustering algorithm. This analysis presents that efficient EVCSs can be generally characterized with the high number of nearby EVCSs and low level of the traffic congestion.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.27 no.6
• /
• pp.771-781
• /
• 1994

Monthly measurements made at 15 stations along the axis of the upper Neuse River estuary show a highly variable degree of correlation between concentration of suspended particulate material (SPM) and attenuation coefficient (c) of light as measured by transmissometer. Coefficients of determination along transect lines ranged from $0.12{\sim}0.93$ and calibration slopes ranged from $0.50{\sim}5.63$. When examined on a station-by-station basis, coefficients of determination ranged from $0.21{\sim}0.96$ and calibration slopes ranged from $1.04{\sim}4.94$. Surface calibrations made at individual stations over the full 13-month period were the most consistent of all observations and were considerably better than calibrations made using all of the stations on a given day. Organic content, which can dominate the suspended sediment load during some months, does not appear to explain the variations in reliability of the calibrations. However, an abundance of large aggregates with time-varying size and shape distributions may be partly responsible for variations in optical properties of the sediments, and thus may confound the relationship between SPM and c in the Neuse River estuary Time-varying calibrations to account for non-negligible changes in optical properties may not suffice in complex estuarine environments where the in situ particle dynamics are poorly understood. However, the best use of Beam Transmissometer will continue to be for applications such as detecting water-column events or for use in situations where wide error bars in establishing SPM concentrations are acceptable.

• Korean Chemical Engineering Research
• /
• v.59 no.1
• /
• pp.68-76
• /
• 2021

As hazardous chemicals are releasing in process industries such as chemical & petro-chemical plants, the importance of initial responses has been always emphasized. However, little attention of quantitative analysis of the consequence by different initial responses during releasing of the chemicals has been done. The main objective of current paper is to investigate the effects of initial responses for the release accidents of hydrofluoric acid. For this, a simplified equation that can easily calculate the effect distance by varying concentrations of hydrofluoric acid was firstly deduced. In addition, a causal loops for the initial response steps using the system dynamics technique was constructed during release of 50% hydrofluoric acid. The effect distances according to different scenarios of the initial actions were also quantitatively analyzed by applying the simplified equation to the causal map. As a result, the highest reduction rate on the maximum effect distance was obtained with 'start time of action after leak detection' being about 87% while the lowest was 'arrival time of professional response team' being about 50%, as expected. It is expected that the results gained from the current study can be helpful as of basics of the initial response to the workplace, dealing with the hydrofluoric acid.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.24 no.2
• /
• pp.97-108
• /
• 2012

A Lagrangian particle tracking model coupled with the ECOM3D were used to study on the behavior of fresh water released from the Namgang Dam in terms of residence time in Kangjin Bay, South Sea, Korea. Model was calibrated until skill cores for elevation, velocity, temperature and salinity are satisfied over 85%. In the numerical simulation, particles were released in 1 hour time interval from the northern boundary. The different patterns of particle trajectory are identified under the varying dynamics from tidal to density-driven current. The average residence time of total particles are approximately 65.9 hours in the entire Kangjin Bay. The average residence time were increased from 55~65 to 70~80 hours during maximum discharge period. Discharge rate of fresh water and average residence time in the Kangjin Bay is high correlated with correlation coefficient over 0.81.