• Journal of the Korean Vacuum Society
• /
• v.6 no.3
• /
• pp.255-262
• /
• 1997

Titanium nitride (TiN) films were prepared by reactive sputter deposition in mixed gas of Ar+$N_2$. The volume percentage of $N_2$ in the working gas was chosen so as to grow stoichiometric TiN films and the substrate temperature during film growth was set from room temperature to $700^{\circ}C$. Stoichiometric $Ti_{0.5}N){0.5}$ films with (111) texture were grown at temperatures over $600^{\circ}C$, while films prepared at temperatures below $600^{\circ}C$ showed N-rich TiN. The composition X and y in the $Ti_xN_y$ films determined by XPS and RBS varied within 5% with the substrate temperature. The sheet resistance of the TiN films decreases as the substrate temperature increased. TiN film prepared at $600^{\circ}C$ showed 14.5$\Omega\Box$, and it decreased to 8.9$\Omega\Box$ after the sample was annealed at $700^{\circ}C$, 30 sec in Ar-gas ambient by RTA. By far, high quality stoichiometric TiN films by reactive sputtering in the mixed gas ambient could be prepared at substrate temperature over $600^{\circ}C$.

• Journal of the Korean Ceramic Society
• /
• v.30 no.6
• /
• pp.510-516
• /
• 1993

$PbTiO_3$ thin films have been formed by rapid thermal annealing(RTA) of $TiO_2$/Pb/$TiO_2$ multilayer films deposited on Si wafers by RF sputtering. Based on the optimal depositon conditions of TiO2 and Pb, $TiO_2$/Pb/$TiO_2$ three layers were deposited for 900$\AA$ each. These films were subjected to RTA process at the temperatures ranging from $400^{\circ}C$ to $900^{\circ}C$ for 30 seconds in air, and were analyzed by X-ray diffraction and transmission electron microscopy to investigate the phases and the microstructures. As a result, perovskite $PbTiO_3$ phases was obtained above $500^{\circ}C$ with the trace of unreacted $TiO_2$. RBS analysis revealed the anisotropic behavior of diffusion that the diffusivity of Pb to the bottom $TiO_2$ layer was faster than that of Pb to the top $TiO_2$ layer. The amorphous Pb-silicate was formed between film and Si substrate due to the diffusion of Pb, but Pb-silicate existed locally at the interface and the amount of that phase was very small. Therefore the effect of bottom $TiO_2$ layer as a diffusion barrier was confirmed. $PbTiO_3$ films formed by current technique showed a relative dielectric constant of 60, and the maximum breakdown field reached 170kV/cm.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.171-171
• /
• 2010

In this work, we investigated the effect of the oxidation temperature on the unipolar and bipolar resistance switching behaviors of the oxidized TiO-x films. TiOx films on Pt electrodes were fabricated by the oxidation of Ti films at $550^{\circ}C$ for 1 to 3 hours. The unipolar and bipolar resistance switching properties were investigated with the oxidation temperature and time. Also, the crystal structure and the physical properties such as chemical bonding states of TiOx layers were characterized in addition to the resistance switching characteristics. The resistance switching behaviors of TiOx films oxidized at above $450^{\circ}C$ and below $650^{\circ}C$ was shown. So, we investigated that the resistance switching behaviors of TiOx films oxidized at $550^{\circ}C$ with the oxidation time from 1 to 3 hour. The memory windows of unipolar switching in the oxidized TiOx films were reduced with increasing the oxidation time, but those of the bipolar switching were slightly enlarged. The enlargement of rutile TiO2 peak with increasing the oxidation time and temperature was studied by X-ray diffraction. An increase of non-lattice oxygen and Ti3+ in the TiOx films with the oxidation times was investigated by X-ray photoemission spectroscopy. It was expected that the uipolar and bipolar resistive switching of the oxidized TiOx film was strongly related with the migration of non-lattice oxygen anions and schottky barrier height, respectively.

• Transactions on Electrical and Electronic Materials
• /
• v.1 no.2
• /
• pp.28-31
• /
• 2000

BaTiO$_3$cerameic thin films doped with Mn were manufactured by rf/dc magnetron sputter technique. We have investigated crystal structure, surface morphology and PRCR(positive-temperature coefficient of resistance) characteristics of the specimen depending on second heat-treatment temperature. Second heat treatment of the specimen were performed in the temperature range of 400 to 1350$\^{C}$ X-ray diffraction patterns of BaTiO$_3$ thin films show that the specimen heat treated below 600$\^{C}$ is an amorphous phase and the one heat treated above 1100$\^{C}$ forms a poly-crystallization . In this specimen heat-treated at 1300$\^{C}$, a lattice constant ratio(c/a) was 1.188. Scanning electron microscope(SEM) image of BaTiO$_3$ thin films of the specimen heat treated in between 900 and 1100$\^{C}$ shows a grain growth. At 1100$\^{C}$, the specimen stops grain-growing and becomes a poly-crystallization . A resistivity-temperature characteristics of the specimen depends on the doping concentrations of Mn. A resistivity ratio between the value at room temperature and the one above Curie temperature was 10$^4$ for pure BaTiO$_3$ thin films and 10$\^$5/ fo BaTiO$_3$ : additive 0.127mol% MnO

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.10 no.2
• /
• pp.111-115
• /
• 2000

$BaTIO_3$ thin films were prepared on (100) $BaTIO_3$ substrates by coating- pyrolysis process using metal-organic compounds of Ba and Ti. The amorphous films prefired at $450^{\circ}C$were crystallized above $700^{\circ}C$ under oxygen partial pressure of $2\times 10^{-4}$. The lattice parameters of the perpendicular axis for the $BaTIO_3$ thin films heat-treated below $800^{\circ}C$ were closer to a value of cubic $BaTIO_3$, whereas those above $800^{\circ}C$ were closer to a value of tetragonal BaTiG. The results of XRD P scan and pole-figure analyses indicated that BaTiO, thin films have an epitaxial relationship with the $SrTiO_3$ substrates. The $BaTIO_3$thin films annealed at$800^{\circ}C$ showed the surface with island-like grains about 0.4$mu \textrm{m}$ and the cross section of 0.8 $mu \textrm{m}$ thickness with granular grains.

• Journal of the Korean institute of surface engineering
• /
• v.25 no.5
• /
• pp.223-233
• /
• 1992

(Ti, Al)N films were deposited on 304 stainless steel by D.C. magnetron sputtering using Al target and Ti plate. The properties of (Ti, Al)N films such as composition, microhardness, grain size, crystal structure were investigated. The chemical composition of (Ti, Al)N films was similar to the sputter area ratio of titanium to aluminum target by means of EDS and AES survey. The higher bias voltage to substrate and the smaller input of N2 gas showedthe increased microhardness and the finer grain size of the films. The results obtained from this study show, it is belived, that the (Ti, Al)N film by D.C.magne-tron sputtering is promising in the wear resistance use.

• Journal of the Korean Ceramic Society
• /
• v.43 no.6 s.289
• /
• pp.362-368
• /
• 2006

Epitaxial $Ba_{0.5}Sr_{0.5}TiO_3$ (BSTO) thin films have been grown on TiN buffered Si (001) substrates by Pulsed Laser Deposition (PLD) method and the effects of substrate temperature and oxygen partial pressure during the deposition on their dielectric properties and crystallinity were investigated. The crystal orientation, epitaxy nature, and microstructure of oxide thin films were investigated using X-Ray Diffraction (XRD) and Transmission Electron Microscopy (TEM). Thin films were prepared with laser fluence of $4.2\;J/cm^2\;and\;3\;J/cm^2$, repetition rate of 8 Hz and 10 Hz, substrate temperatures of $700^{\circ}C$ and ranging from $350^{\circ}C\;to\;700^{\circ}C$ for TiN and oxide respectively. BSTO thin-films were grown on TiN-buffered Si substrates at various oxygen partial pressure ranging from $1{\times}10^{-4}$ torr to $1{\times}10^{-5}$ torr. The TiN buffer layer and BSTO thin films were grown with cube-on-cube epitaxial orientation relationship of $[110](001)_{BSTO}{\parallel}[110](001)_{TiN}{\parallel}[110](001)_{Si}$. The crystallinity of BSTO thin films was improved with increasing substrate temperature. C-axis lattice parameters of BSTO thin films, calculated from XRD ${\theta}-2{\theta}$ scans, decreased from 0.408 m to 0.404 nm and the dielectric constants of BSTO epitaxial thin films increased from 440 to 938 with increasing processing oxygen partial pressure.

• Korean Journal of Materials Research
• /
• v.12 no.11
• /
• pp.835-839
• /
• 2002

Metal-Ferroelectric-Metal(MFM) capacitors were prepared using $Bi_{3.3}$ $La_{0.7}$ $Ti_3$$O_{12}$ (BLT) ferroelectric thin films which were spin coated on $Pt/Ti/SiO_2$/Si substrates by the Sol-Gel method. BLT thin films annealed at above $650^{\circ}C$ showed polycrystalline structures with typical c-axis preferred orientation. The grain size and surface roughness were increased as the annealing temperature increased from $650^{\circ}C$ to $700^{\circ}C$. In addition, the full width at half maximum (FWHM) values were decreased with increasing annealing temperatures, indicating the improvement of crystallinity. The remanent polarization (2Pr= $Pr^{+}$ $+Pr^{-) }$ and leakage current of the BLT film annealed at $650^{\circ}C$ were about 29.3 $\mu$C/cm$^2$ and $2.3$\times$10^{-8}$$ A/cm^2$ at 3V. There were no distinct changes in the retention charges after $10^{10}$ polarization switching cycles, showing good fatigue property of the annealed BLT films.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.12 no.1
• /
• pp.7-10
• /
• 2002

$TiO_2$ thin films were prepared by coating and subsequent pyrolysis processes using Titanium-naphthenate as a raw material. $TiO_2$ thin films were made by spin-coating technique on the glass substrates, and heat treated at 45$0^{\circ}C$, The transmittance, refractive index, crystallinity and surface morphology of the $TiO_2$ thin films were measured by UV/Vis spec trophotometer, x-ray diffractometer and scanning electron microscope. $TiO_2$thin films on the slide glass showed the trans mittance of 70-90% and refractive index of 2.6 at 420 nm. The results of XRD and SEM showed that the $TiO_2$ thin films exhibited the anatase phase and the thread-like surface morphology.

• Journal of the Korean Vacuum Society
• /
• v.1 no.1
• /
• pp.100-105
• /
• 1992

Auger electron spectroscopy (AES) and X-ray photoelectron spectroscopy (XPS) analyses have been performed on double-structured Au/V and Au/Ti thin films after heat treatment at 500$^{\circ}$C in air. V- and Tiunderlays sandwiched between gold thin films and SiOz substrates form oxides on the free surface of gold films during the heat treatment. The chemical compositions of the oxides were identified as V205 and TiOz in Au/V and Au/Ti thin films, respectively.