• Journal of Magnetics
• /
• v.19 no.2
• /
• pp.121-125
• /
• 2014

$CoFe_2O_4(CFO)/BaTiO_3(BTO)/CoFe_2O_4(CFO)$ multilayered thin films were deposited on $Pt/TiO_2/SiO_2/Si$ substrates by the pulsed laser deposition (PLD) system with KrF excimer laser (${\lambda}=248nm$). BTO, CFO, BTO/CFO and CFO/BTO/CFO structured thin films were prepared and their crystal structures and microstructures, as well as their magnetic and magneto-electrical properties, were studied. The C-V characteristics of these multilayered thin films with different capacitor structures were obtained to confirm the change in their capacitances under a magnetic field. Finally, the capacitance of the CFO/BTO/CFO thin film as a function of bias voltage under an in-plane magnetic field of 1,000 Oe increased to 951.04 pF at 1 MHz, from 831.90 pF measured under no magnetic field, indicating 14.3% increase in magnetocapacitance.

• Proceedings of the KIEE Conference
• /
• 2005.11a
• /
• pp.176-178
• /
• 2005

Ferroelectric $Bi_{3.25}Nd_{0.75}Ti_{3}O_{12}(BNdT)$ thin films were proposed for capacitor of FeRAM. The BNdT thin films were grown on Pt/Ti $SiO_2/P-Si(100)$ substrates by the RF magnetron sputtering deposition. The dielectric properties of the BNdT were investigated by varying deposition temperatures. Increasing deposition temperature, the (117) peak was increased. An increase of columnar and recrystalline structure of BNdT films with increasing deposition temperature was observed by the Field Emission Scanning Electron Microscopy(FE-SEM). The dielectric constant and dielectric loss of the BNdT thin films with deposition temperature of $600^{\circ}C$ were 319 and 0.05, respectively.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.237-238
• /
• 2008

The films of Vanadium tungsten oxide, $V_{1.85}W_{0.15}O_5$, were grown on Pt/Ti/$SiO_2$/Si substrate by RF sputtering method. The $V_{1.85}W_{0.15}O_5$ thin films deposited on Pt/Ti/$SiO_2$/Si substrates by RF sputtering method exhibited fairly good TCR and dielectric properties. It was found that film crystallinity, dielectric properties, and TCR properties were strongly dependent upon the annealing temperature. The dielectric constants of the $V_{1.85}W_{0.15}O_5$ thin films annealed at $300^{\circ}C$ were 55, with a dielectric loss of 1.435, respectively. Also, the TCR values of the $V_{1.85}W_{0.15}O_5$ thin films annealed at $300^{\circ}C$ were about -3.6%/K.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.22 no.1
• /
• pp.29-34
• /
• 2009

PLZT thin films were deposited on platinized silicon (Pt/$TiSiO_2$/Si) substrate by RF magnetron sputtering. A $TiO_2$ buffer layer was fabricated, prior to deposition of PLZT films. the layer was strongly affected the crystallographic orientation of the PLZT films. X-ray diffraction was performed on the films to study the crystallization of the films as various substrate temperatures (Ts). According to increasing Ts, preferred orientation of films was changed (110) plane to (111) plane. The ferroelectric, dielectric and electrical properties of the films were also investigated in detail as increased substrate temperatures. The PLZT films deposited at $400^{\circ}C$ showed good ferroelectric properties with the remnant polarization of $15.8{\mu}C/cm^2$ and leakage current of $5.4{\times}10^{-9}\;A/cm^2$.

• Journal of the Korean Society for Heat Treatment
• /
• v.22 no.5
• /
• pp.267-274
• /
• 2009

Titanium Chromium Nitrided (TiCrN) coatings were deposited on stainless steel 316 L and Si (100) wafer by inductively coupled plasma assisted D.C. magnetron sputtering at the various sputtering power on Cr target and $N_2/Ar$ gas ratio. Increasing the sputtering power of Cr target, XRD patterns were changed from TiCrN to nitride $Cr_2Ti$. The maximum hardness was $Hk_{3g}$ 3900 at $0.3\;N_2/Ar$ gas ratio. The thickness of the TiCrN films increased as the Cr target power increased, and it showed over $Hk_{5g}3100$ hardness at 100 W, 150 W. TiCrN films were deposited by the ICP assisted DC magnetron sputtering shown good wear resistance as the $N_2/Ar$ gas ratio was 0.1, 0.3.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1997.10a
• /
• pp.183-190
• /
• 1997

The wear behaviors of $Al_2O_3-40%TiO_2$ deposited on casting aluminum alloy(ASTM A356) by plasma spray against SiC ball have been investigated experimentally. Friction and wear tests are carried out at room temperature. The friction coefficient of $Al_2O_3-40%TiO_2$ coating is lower than that of pure $Al_2O_3$ coating(APS). It is found that low friction correspond to low wear and high friction to high wear in the experimental result. The thickness of $Al_2O_3-40%TiO_2$ coatings indicated the existence of the optimal coating thickness. It is found that a voids and porosities of coating surface result in the crack generated. As the tensile stresses in coating increased with the increased friction coefficient. The columnar grain of coating will be fractured to achieve the critical stress. It is found that the cohesive of splats and the porosity of surface play a role in wear characteristics. It is suggested that the mismatch of thermal expansion of substrate and coating play an important role in wear performance. Tensile and compressire under thermo-mechanical stress may be occurred by the mismatch between thermal expansion of substrate and coating. This crack propagation above interface is observed in SEM.

• Tribology and Lubricants
• /
• v.15 no.1
• /
• pp.39-45
• /
• 1999

The wear behavior of $Al_2$O$_3$-40%TiO$_2$deposited on casted aluminum alloy (ASTM A356) by APS (Air Plasma Spray) against SiC ball has been investigated in this work. Wear tests were carried out at room temperature. The friction coefficient of $Al_2$O$_3$-40%TiO$_2$coating is lower than that of pure $Al_2$O$_3$coating(APS). $Al_2$O$_3$-40%TiO$_2$coating indicated the existence of the optimal coating thickness. It is found that voids and pores of coating surface resulted in the generation of cracks, and the cohesive of splats and the porosity of surface play a role in wear characteristics. It is suggested that the mismatch of thermal expansion of substrate and coating play an important role in wear performance. Tension and compression under thermo-mechanical stress may be occurred by the mismatch between thermal expansion of substrate and coating. The crack propagation above interface is observed in SEM.

• Korean Journal of Materials Research
• /
• v.8 no.12
• /
• pp.1146-1151
• /
• 1998

The crystallization behaviour of perovskite $PbTiO_3$ for the samples heat- treated at various temperatures for various times in the $PbO-TiO_2-A1_2O_3-SiO_2$, glass system has been investigated by the means of X-ray diffraction (XRD) and scanning electron microscopy (SEM) analyses. Higher crystallinity obtained in the sample heat-treated at higher temperature for longer time. With increasing heat-treatment time, dielectric constant of the samples heat-treated at $610^{\circ}C$ and $650^{\circ}C$ increased, but that of the sample heat- treated at $800^{\circ}C$ decreased. Loss tangent of the heat-treated samples was not much influenced by heat-treatment conditions. Piezodielectric charge constant was approximately $1.0\times10^{-12}~8.0$\times$10^{-12}C/N$ in the samples heat-treated at $800^{\circ}C$ for 1h, 2h, and 8h.

• Journal of the Korean Ceramic Society
• /
• v.25 no.1
• /
• pp.42-48
• /
• 1988

Commercially available PTCR (Postive Temperature Coefficient of Resistivity) ceramics which have low room temperature resistance, high PTC effect and temperature coefficient were prepared by La3+ doped semiconducting barium calcium titanate soild solutions. PTCR characteristics were remarkably improved by addition of AST (1/3 Al2O3$.$3/4SiO2$.$1/4TiO2) and MnCl2. That can be explained by formation of liquid phase during sintering and acceptor level on the intergranular layer. Resistivity anormaly increased with decreasing cooling rate. Optimum manufacturing conditions were cooling rate below 100$.$C/hr, Ca and Mn content of 4 mol% &, 0.09-0.12mol% respectively.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.11a
• /
• pp.172-173
• /
• 2006

Metal-ferroelectric-insulator-semiconductor (MFIS) structures with $Bi_{3.35}La_{0.75}Ti_3O_{12}$ (BLT) ferroelectric film and Zirconium oxide ($ZrO_2$) layer were fabricated on p-type Si(100). $ZrO_2$ and BLT films were prepared by sol-gel technique. Surface morphologies of $ZrO_2$ and BLT film were measured by atomic force microscope (AFM). The electrical characteristics of Au/$ZrO_2$/Si and Au/BLT/$ZrO_2$/Si film were investigated by C-V and I-V measurements. No hysteretic characteristics was observed in the C-V curve of the Au/$ZrO_2$/Si structure. The memory window width m C-V curve of the Au/BLT/$ZrO_2$/Si diode was about 1.3 V for a voltage sweep of ${\pm}5$ V. The leakage current of Au/$ZrO_2$/Si and Au/BLT/$ZrO_2$/Si structures were about $3{\times}10^{-8}$ A at 30 MV/cm and $3{\times}10^{-8}$ A at 3 MV/cm, respectively.