• Progress in Superconductivity
• /
• v.6 no.1
• /
• pp.19-23
• /
• 2004

YBCO do superconducting quantum interference device (SQUID) magnetometers based on bicrystal Josephson junctions on 10 mm ${\times}$ 10 mm $SrTiO_3$ substrates have been fabricated. The pickup coil of the device was designed to have 16 parallel loops with 50-fm-wide lines. We could obtain optimised direct coupled YBCO SQUID magnetometer design with field sensitivity $B_{N}$ $\Phi$/ of $4.5 nT/\Phi_{0}$ and magnetic field noise $B_{N}$ of about $22 fT/Hz^{1}$2/ with an I/f corner frequency of 2 Hz measured inside a magnetically shielded room. Preliminary results of magnetocardiograph measurement using the HTS SQUID magnetometers show signal to noise ratio of about 110, which is comparable to the quality of a commercial MCG system based on Nb-SQUIDs.

• International Journal of Korean Welding Society
• /
• v.4 no.1
• /
• pp.46-52
• /
• 2004

To combine the mechanical advantages of ceramics with those of metals, one often uses both materials within one composite component. But, as known, they have different material properties and fracture behaviors. In this study, a four-point bending test is carried out on $Si_3N_4$ joined to ANSI 304L stainless steel with a Ti-Ag-Cu filler and a Cu interlayer at room temperature to evaluate their longitudinal strain behaviors. And, to detect localized strain, a couple of strain gages are pasted near the joint interfaces of the ceramic and metal sides. The normal strain rates are varied from $3.33{\times}10^5$ to $3.33{\times}10^{-1}s^{-1}$ Within this range, the experimental results showed that the four-point bending strength and the deflection of the interlayer increased with increasing the strain rate.

• Transactions of Materials Processing
• /
• v.23 no.1
• /
• pp.29-34
• /
• 2014

The damage level of the die surface was predicted by estimating the surface roughness with a finite element analysis and the wear characteristics. Wear and friction tests were conducted to compare the wear characteristics for three kinds of surface treatments - CrN, TiAlN and AlCrN coatings. A prediction model was derived from the surface roughness results with respect to contact pressure and sliding speed which were obtained from the wear test. Surface roughness values for the damage regions of the die surface were compared between the experiments and the prediction model, which shows fairly good agreement with each other.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.41 no.6
• /
• pp.687-693
• /
• 1992

To improve dielectric, piezoelectric and temperature stability in 0.50Pb(SnS11/2TSbS11/2T)OS13T - 0.35PbTiOS13T - 0.60PbZrOS13T + 0.4[wt%]MnOS12T piezoelectric ceramics which is used for surface acoustic wave devices, CrS12TOS13T was added and the specimens were fabricated by Hot Press method, and their characteristics were measured with CrS12TOS13T addition. From the results, in the specimen added by 0.2[wt%]CrS12TOS13T, dielectric constant and mechanical quality factor were 380 and 2307, respectively, and it was suited for surface acoustic wave device and the temperature coefficient of the resonant frequency in the specimen added by 0.4[wt%]CrS12TOS13T was the least value of 74.96[ppm/$^{\circ}C$].

• Journal of Surface Science and Engineering
• /
• v.29 no.6
• /
• pp.628-633
• /
• 1996

Large saturation magnetization $4pM_s$ is essentially required for soft magnetic thin layers used in magnetic recording devices. Amorphous Co-based alloys and Fe-Co alloys may be regarded as one of the candidates for soft magnetic materials which possess large $4\piM_s$. Some preparation process to improve soft magnetism of these films were performed in this study. Addition of Ta seemed to be effective to change the magnetostriction constant $\lambda$ from positive value to negative one. The magnetoelastic energy $K_e$ is strongly dependent on $\lambda$. $(Co_{95.7}Zr_{4.3})_{100-x}Ta_x$ films with $K_e$ of negative value have sufficiently soft magnetic characteristics. $Fe_{90}Co_{10}$ alloy exhibits extremely large $4\piM_s$, of about 24 kG. Addition of N and Ta to $Fe_{90}Co_{10}$ films improved the soft magnetism of them. The $Fe_{82.0}Co_{7.6}Ta_{10.4}$:N/Ti multilayered films exhibit better soft magnetic properties and better thermal stability than Fe-Co-Ta:N singlelayer films.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.10a
• /
• pp.1418-1423
• /
• 2004

High speed machining experiment on the heat-treated mold steel(STAVAX and CALMAX of hardness HRc 53) is carried using TiAlN coated ball endmill. Tool life and wear characteristics under the various machining parameters and cooling methods are investigated. Effect of cooling method on life and wear of the tool was compared. For most cases, tool life was not determined by the amount of wear but by th chipping on the cutting edge. It is found that tool manufacturer's cutting parameters generally agrees with the results of this experiment.

• Journal of the Korean Vacuum Society
• /
• v.4 no.S1
• /
• pp.81-86
• /
• 1995

Aluminum has been deposited selectively on TiN surfaces in the presence of Si, SiO2 from Dimethyethylamine Alane(DMEAA). The film properties of the deopsited AI film were determined by various methods(SEM, Auger, UV-photospectrometer, Four point-probe, XRD). The effect of in-situ H2 plasma precleaning was studied. The effect of gap distance, pressure and temperature on the properties(crystallinity, resistance, grain size, morphology) of AI film and on the growth rates was investigated. It was found that the plasma precleaning promotes the growth rate and there exists optimum thmperature for maximum growth rate.

• 한국전기화학회:학술대회논문집
• /
• 2002.04a
• /
• pp.28-28
• /
• 2002

• 한국전기화학회:학술대회논문집
• /
• 2001.10a
• /
• pp.19-19
• /
• 2001

• Proceedings of the Korean Magnestics Society Conference
• /
• 2002.12a
• /
• pp.42-43
• /
• 2002

Spintronics is a rapidly expanding research area because of recent developments in the physics of spin-dependent phenomena. For use as spintronic materials, dilute magnetic semiconductors (DMS) are of considerable interest as spin injectors for spintronic devices.$^{[1]}$ Many researchers have studied DMS, in which transition metal atoms are introduced into the lattice, thus inserting local magnetic moments into the lattice. (omitted)