• Computers and Concrete
• /
• 제1권4호
• /
• pp.371-388
• /
• 2004

Our objective is to model static multi-cracking processes in concrete. The explicit dynamic relaxation (DR) method, which gives the solutions of non-linear static problems on the basis of the steady-state conditions of a critically damped explicit transient solution, is chosen to deal with the high geometric and material non-linearities stemming from such a complex fracture problem. One of the common difficulties of the DR method is its slow convergence rate when non-monotonic spectral response is involved. A modified concept that is distinct from the standard DR method is introduced to tackle this problem. The methodology is validated against the stable three point bending test on notched concrete beams of different sizes. The simulations accurately predict the experimental load-displacement curves. The size effect is caught naturally as a result of the calculation. Micro-cracking and non-uniform crack propagation across the fracture surface also come out directly from the 3D simulations.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2006년 창립20주년기념 정기학술대회 및 국제워크샵
• /
• pp.25-28
• /
• 2006

This paper dealt with the LPS process for the development of high performance SiC materials, based on the detailed analysis of their microstructure and mechanical properties. The submicron SiC powder was used for the fabrication of LPS-SiC materials. A mixture of $Al_2O_3$ and $Y_2O_3$ particles was also used as a sintering additive in the LPS process. LPS-SiC materials were fabricated at different temperatures, using various additive composition ratio ($Al_2O_3/Y_2O_3$). The total amount of additive materials ($Al_2O_3+Y_2O_3$) was fixed as 10 wt%. The characterization Of LPS-SiC materials was investigated by means of SEM, XRD and three point bending test. The LPS-SiC material represented a relative density of about 98 % and a flexural strength of about 800MPa, when it was fabricated at the temperature of $1820^{\circ}C$ and the additive compositional ratio of 1.5.

• 열처리공학회지
• /
• 제7권3호
• /
• pp.160-168
• /
• 1994

This was studied about mechanical characteristic of AC4A/SiCw 10-30% reinforced composites. Tensile strength of pressed base metal(base metal) with SiCw preform was higher than without pressed base metal(AC4A). If SiCw whisker volume fraction was increased, tensile strength at room temperature was increased. And tensile strength of SiCw 30% was about $35kg/mm^2$. Tensile strength of SiCw 30 % $400^{\circ}C$ at same time aging was the most excellence, about $40kg/mm^2$. The fracture energy value of composite material at three point bending test was higher than AC4A. Dislocation at matrix of composite material was evenly distributed. But dislocation around whisker of composite material was more existed than matrix. The reasom was thought of pile-up around whisker.

• EDISON SW 활용 경진대회 논문집
• /
• 제4회(2015년)
• /
• pp.217-222
• /
• 2015

In this paper, a study was conducted for the optimization through shear web of shape the Edison program in wind power blade. We measured the displacement and stress distribution through two optimization methods to select the model with the smallest displacement and stress values. Before running the analysis, We try to find the inflection point through the shear web of the model and then analyze by introducing the geometric nonlinearity. The first optimization variables are introduced by the pitch angle and three web shapes. Third model such a honeycomb structure is good way to get an advantage for bending test. According to a method of previous optimization, third model is chosen and then the thickness of the web and blade as a variable is introduced, it is extracted as a result of displacement and the maximum stress per mass.

• 한국임상수의학회지
• /
• 제20권3호
• /
• pp.345-350
• /
• 2003

We were preferred bovine cortical bone to the others in xenobonegrafts for human and small animals, because those were not limited to supply and have sufficient size for bone transplantation. The strength (ST) and stiffness (SF) of cortical bone in bone grafts were very important. The strength and stiffness of cortical bone were much difference according to position of long bone in bovine limbs because which were biomechanical different to bear body weight. Therefore, we determinated by three bending point test methods the strength and stiffness of cortical bone which were collected in diaphysis of humerus, radius, femur and tibia of bovine. In the results, the strengths and stiffness among these were highest in radius by ST: 253.84$\pm$40.80 MPa, SF: 7.89$\pm$1.91 Gpa and lowest in humerus by ST: 185.69$\pm$28.54 MPa, SF: 6.21$\pm$1.22 Gpa.

• 한국반도체및디스플레이장비학회:학술대회논문집
• /
• 한국반도체및디스플레이장비학회 2006년도 춘계학술대회
• /
• pp.251-254
• /
• 2006

In this paper, cutting qualifies and fracture strength of silicon dies by laser dicing are investigated. Laser micromachining is the non-contact process using thermal ablation and evaporation mechanisms. By these mechanisms, debris is generated and stick on the surface of wafer, which is the problem to apply laser dicing to semiconductor manufacture process. Unlike mechanical sawing using diamond blade, chipping on the surface and crack on the back side of wafer isn't made by laser dicing. Die strength by laser dicing is measured via the three-point bending test and is compared with the die strength by mechanical sawing. As a results, die strength by the laser dicing shows a decrease of 50% in compared with die strength by the mechanical sawing.

• 마이크로전자및패키징학회지
• /
• 제9권3호
• /
• pp.25-29
• /
• 2002

단일이온교환 공정을 도입하여 평판디스플레이에 사용되는 기판유리를 대상으로 이온교환 거동 및 기계적 특성에 대하여 조사하였다. 효과분석으로는 온도와 시간 변화에 따른 $K^+$ 이온의 침투깊이, 이온교환량, 밀도, 열팽창계수를 관찰하였다. 기판유리의 기계적 특성으로는 3점 곡강도와 만곡변화를 관찰하였으며, 광학현미경을 사용하여 곡강도 측정 후 파괴된 시편의 형태를 조사하였다.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2000년도 춘계학술대회 논문집
• /
• pp.242-249
• /
• 2000

The fatigue strength of welded aluminum alloy component has been evaluated. Extruded aluminum alloy component Al 6005-T6 was considered. That component could be one of appropriate candidates for floor structure in railway cars. Finite element analysis has been performed to obtain stress distribution in the welded aluminum component. The results of finite element analysis have been applied in designing the experimental setup for fatigue strength evaluation of welded component. Three point bending fatigue test has been employed, until fracture occurs, to evaluate the fatigue strength of the welded component. In addition, the fatigue strength of the component has been compared with that of specimen.

• 한국마이크로전자및패키징학회:학술대회논문집
• /
• 한국마이크로전자및패키징학회 2002년도 추계기술심포지움논문집
• /
• pp.177-179
• /
• 2002

A1$_2$ $O_3$기판재료의 $K_{IC}$ 증가를 위한 재료설계를 시도하였다. 먼저 A1$_2$ $O_3$기판을 구성하는 A1$_2$ $O_3$다층구조물에 적절한 다공성 중간층을 삽입하는 샌드위치 구조물을 제조하였다. 제조된 A1$_2$ $O_3$구조물의 미세구조를 관찰하였고, Vickers 경도와 three-point bending test를 통해서 단일조성 구조물과 샌드위치 구조물의 경도와 인성 측정치를 비교하였다. 다공층을 삽입한 A1$_2$ $O_3$샌드위치 구조물의 Single-Edge Notched Beam이 단일 조성의 구조물에 비해 파괴강도와 인성이 향상되는 결과를 얻었다.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 1998년도 추계학술대회 논문집
• /
• pp.553-559
• /
• 1998

This thesis studied to evaluate the fatigue behavior and propagation of rail steel under welding line. Test of crack growth was performed by all member of rail under constant amplitude loading at the structures laboratory in Hongik University. The effect of the following parameters with initiated crack length on the bottom edge of rail were studied. Here, fracture mechanics mode is opening mode. and Testing Material is KS50N Rail. From analysis and experimented result on the three Point bending in the lab, This paper presented a effect of crack growth , shape and remaining service life. Further more, according to the variable crack length, variable section and the ratio of section the fatigue behavior and propagation were studied.