• Journal of Korea Foundry Society
• /
• v.21 no.4
• /
• pp.246-252
• /
• 2001

Variation in the microstructure of Mg-5%Al semi-solid slurry during isothermal heating was investigated in relation to initial microstructure, holding time, and holding temperature. Specimens with three different initial microstructures were isothermally heated. Dendritic structure in as-cast ingot was decomposed into solid globules in the semi-solid slurry during isothermal holding, while in the recrystallized specimens prepared by extrusion or rolling the size of solid particles was continuously increased during the heating. Effects of mold temperature and liquid fraction of slurry on the mold filling ability were also studied. Very thin section (0.4 mm) could be successfully filled up to 50 mm by 60% liquid slurry when the mold was heated to $600^{\circ}C$.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.05a
• /
• pp.31-34
• /
• 2006

In this study, $(Ba_{0.7}\;Sr_{0.3})TiO_3$ was coated on Pt/Ti/$SiO_2$/Si wafer by using Sol-Gel method. Coating process was repeated 3~5 times and then sintered at 750[$^{\circ}C$] for 1 hour. Each specimen was analyzed structure and electrical characteristics. In structure characteristics, EDX analyzed the samples ratio of the formation on the structural property. Thermal behavior was observed with TG-DTA and concluded that the heat-treatment of the samples was degreed 750[$^{\circ}C$]. Surface and section of thin films were observed with SEM.

• The Korean Journal of Ceramics
• /
• v.3 no.3
• /
• pp.155-158
• /
• 1997

Highly oriented diamond films were deposited on a (100) silicon substrate by bias enhanced nucleation technique. Both plan-view and cross-section TEM were applied to study the nucleation and growth mechanism of diamond grains. Randomly oriented polycrystalline diamond grains with internal microtwins were observed at the nucleation stage while defect free regions were retained at the growth stage and were apparently related with the epitaxy of diamond films. From our experimental results, the nucleation and texture formation mechanism of diamond films is discussed.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2007.04a
• /
• pp.223-226
• /
• 2007

In current specification, modification factor(B) for web-tapered beam is used to account for the stress gradient and the restraining effect for adjacent spans. However, because these effects are considered together in modification factor, this paper revaluate the accuracy of the modification factor used in current specification. Also this paper investigate the flexural torsional buckling strength of laterally fixed thin-walled arch with doubly symmetric section using the analytical and numerical method. From this investigate the concept of effective length to consider the out-of-plane boundary condition for straight column or beam is not applicate for the flexural-torsional buckling of laterally fixed arches.

• Transactions of Materials Processing
• /
• v.11 no.8
• /
• pp.724-730
• /
• 2002

Due to extremely large reduction of area or extrusion ratio in ordinary production of extruded profiles, anisotropy is naturally induced by large severe deformation during the extrusion process. Therefore, the anisotropic properties play a great role in the post processing of extruded profiles, such as in bending. Moreover, undesirable deformation will be involved when the deformation-induced anisotropy is ignored. In order to observe the deformation-induced anisotropy of the thin-walled product, the proposed algorithm is applied to some chosen industrial extrusion processes. In the present work, the method for prediction of deformation-induced anisotropy employing the Barlats six-component yield potential to the rigid-plastic finite element method is proposed. The proposed algorithm is verified with the comparison to the crystallographic texture analysis, and then applied to the C-section extrusion process using a square die. The predicted anisotropy is then compared with the experimental and computational observations for validating the proposed algorithm.

• Transactions of Materials Processing
• /
• v.23 no.7
• /
• pp.446-452
• /
• 2014

In the current study finite element forming analysis is performed to understand the final geometric accuracy limitations for the stamping of an automotive S-rail from four different steel sheets having tensile strengths of 340MPa, 440MPa, 590MPa and 780MPa. Comparisons between the analysis and the experiments for both springback and formability as measured by the amount of edge draw-in and the thickness distribution were conducted. The springback modes were classified according to a scheme proposed in the current investigation and the error was calculated using the normalized root mean square error method. While the analysis results show fairly good agreement with the experimental data for deformation and formability, the simulation accuracy is lower for predicting wall curl, camber and section twist as the UTS of steel sheet increases.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.35D no.3
• /
• pp.70-81
• /
• 1998

Fiber-Fabry-Perot (FFP) tunable filters, the essential component of WDM transmission, were designed, fabricated and characterized. Multi-layered thin film mirrors that consists of an optical collimater's corss section as a substrate and TiO$_{2}$SiO$_{2}$ alternating multi-layered films as a filter wer designed by means of the transfer matrix method. Fabricated mirrors showed the high reflectivity over around 98% as expected. After fabricating the tuneable filters using PZT, we measured FSR, FWHM, finesse , crosstalk and insertion loss, confirming that the built devices satisfied the optical filter's specifications required in the SEDM transmission systems.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2002.11a
• /
• pp.575-578
• /
• 2002

In this paper, we discuss carrier trapping model and trap characteristics of nitrided oxide thin film. Based on the experimental results, the carrier trapping model for system having multi-traps is proposed and is fitted with experimental data in order to determine trap parameter of nitride oxide and O2 annealed nitrided oxide. As a results of curve fitting, the heavy nitridation of oxide introduces three kinds of traps with capture cross section $\sigma$n1=1.48$\times$10$^{-17}$ $\textrm{cm}^2$, $\sigma$n2=1.51$\times$10$^{-19}$ $\textrm{cm}^2$, $\sigma$p=1.53$\times$10$^{-18}$ $\textrm{cm}^2$ and corresponding trap densities Nnl=2.66$\times$10$^{12}$ Cm$^{-2}$ , Nn2=1.32$\times$10$^{12}$ Cm$^{-2}$ , Np=8.35$\times$10$^{12}$ Cm$^{-2}$ .

• Steel and Composite Structures
• /
• v.10 no.3
• /
• pp.223-243
• /
• 2010

This paper reports recent developments concerning the application of Generalised Beam Theory (GBT) to the structural analysis of steel-concrete composite bridges. The potential of GBT-based semi-analytical or finite element-based analyses in this field is illustrated/demonstrated by showing that both accurate and computationally efficient solutions may be achieved for a wide range of structural problems, namely those associated with the bridge (i) linear (first-order) static, (ii) vibration and (iii) lateral-torsional-distortional buckling behaviours. Several illustrative examples are presented, which concern bridges with two distinct cross-sections: (i) twin box girder and (ii) twin I-girder. Allowance is also made for the presence of discrete box diaphragms and both shear lag and shear connection flexibility effects.

• Proceedings of the KSME Conference
• /
• 2004.04a
• /
• pp.410-414
• /
• 2004

Under longitudinal loading continuous fiber reinforced metal matrix composite(MMC) have interpreted an outstanding performance. However, the applicability of continuous fiber reinforced MMCs is somewhat limited due to their relatively poor transverse properties. Therefore, the transverse properties of MMCs are significantly influenced by the properties of the fiber/matrix interface. In this study, elastic-plastic behavior of transversely loaded unidirectional fiber reinforced metal matrix composites investigated by using elastic-plastic finite element analysis. Different fiber placement(square and hexagon) and fiber volume fractions were studied numerically. The interface was treated as three thin layer (with different properties) with a finite thickness between the fiber and the matrix. The analyses were based on a two-dimensional generalized plane strain model of a cross-section of an unidirectional composite by the ANSYS finite element analysis code.