• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1997.04a
• /
• pp.20-22
• /
• 1997

In ours study, we investigated the various properties in Te-light doped $Sb_{85}$G $e_{15}$ thin films such as the change of reflectance and transmittance according to phase change from amorphous to crystalline states In all films the transmittance was decreased, but the reflectance was increased by annealing. Particularly, the reflectance between as- deposited state and annealed state showed the largest change in the T $e_{0.5}$($Sb_{85}$G $e_{15}$ )$_{99.5}$ thin film at 780nm, which was about 40% in as-deposited state and about 70% in annealed state. Therefore, it might be considered that the T $e_{0.5}$($Sb_{85}$G $e_{15}$ )$_{99.5}$ thin film is recording medium showing to a good optical properties if it is used to optical recording of the phase change type. change type.ype.

• Proceedings of the KIEE Conference
• /
• 1993.07b
• /
• pp.1183-1185
• /
• 1993

The plasma polymerized thin film of MMA+Sty was prepared using a capacitively coupled gas-flow-type reactor. This thin films were also delincated by the electron-beam apparatus with an acceleration voltage 30KV, and the pattern in the resist was developed with the gas-flow-type reactor using an argon as an etchant. The effect of discharge power on groth rate and etching rate of the thin film were studied. The molacular structure of the resist was investigated by ESCA and FT-IR.

• Journal of Korea Society of Industrial Information Systems
• /
• v.6 no.1
• /
• pp.70-76
• /
• 2001

The disc type driver with Nd-Fe-B magnet is one of the servo drivers, which have many applications in various fields. For efficient and easy, it is desirable to be small and thin in its size. However, the driver which uses a conventional wire reel is very difficult to be reduced in its volume. one of alternatives to achieve the above goal is the thick film multilayer winding. The winding method will significantly reduce the total volume of the driver. Therefor this paper proposed the thick film multilayer winding methods and consists of parts: design manufactures, properties and applications.

• Journal of the Korean Physical Society
• /
• v.73 no.12
• /
• pp.1867-1872
• /
• 2018

This study proposes a route for surface modification for p-type cobalt oxide-based gas sensors. We deposit a thin layer of Ni on the Co oxide film by sputtering process and annealed at $350^{\circ}C$ for 15 min in air, which changes a typical sputtered film surface into one interlaced with a high density of hemispherical nanoparticles. Our in-depth materials characterization using transmission electron microscopy discloses that the microstructure evolution is the result of an extensive inter-diffusion of Co and Ni, and that the nanoparticles are nickel oxide dissolving some Co. Sensor performance measurement unfolds that the surface modification results in a significant sensitivity enhancement, nearly 200% increase for toluene (at $250^{\circ}C$) and CO (at $200^{\circ}C$) gases in comparison with the undoped samples.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.14 no.5
• /
• pp.435-443
• /
• 2001

As power durable RF SAW filters, AL-(0∼2wt%)Cu alloy multi-layered thin electrodes were deposited on 42° LiTaO$_3$ piezoelectric substrates by magnetron sputtering process, and then ladder-type RF SAW filters, satisfying the electrical specification of CDMA transmission band, were fabricated through optimizing SAW resonator structures. The temperature of film electrodes in SAW filter was increased with RF power, and reached the maxima to cause a failure of SAW filters at the cut-off frequencies of the RF filter band. As RF power increases, the electrodes of Al-Cu alloy showed higher power durability than that of pure Al. The multi-layer laminated film of Al-1wt.% Cu/Cu/Al-1wt%Cu resulted in the best power durability up to 4W of RF power. Every film electrode, however, was destroyed within seconds whenever applying a critical RF power to SAW filters, regardless of the composition and structure of film electrodes. The breakdown of film electrodes under FR power seems to believe due to the fatigue of electrodes caused by repetitive cyclic stress of surface acoustic wave, which is amplified as RF power increases.

• Proceedings of the KIEE Conference
• /
• 2001.04a
• /
• pp.129-131
• /
• 2001

This paper represents the method is to design thin film spiral type inductor using the analytic method and to evaluate the characteristics of the high frequency inductors using HFSS simulation program. The magnetic circuit of the thin film inductor can be successfully simulated by the HFSS.

• Journal of the Korean Magnetics Society
• /
• v.5 no.5
• /
• pp.710-715
• /
• 1995

Magnetic domains were observed using an image lock-in technique for backscattered electron contrast (Type II) with a 200 kV scanning electron microscope. Backscattered electrons indicate a difference in magnetic domain structures at the upper and lower parts of the upper pole in thin-film heads, changing the acceleration voltage. With this method, it is also possible to observe the domain structure of the thin-film head pole through a 10 to $20\;\mu\textrm{m}$ protective layer, and the upper shield of the MR head through the coil in the resist, alumina overcoat, and upper pole.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07b
• /
• pp.913-917
• /
• 2003

In the electronic components and devices fabrication, thin film resistors with low TCR(temperature coefficient of resistance) and high precision have been used over 3 GHz microwave in recent years. Ni-Cr alloys thin films resistors is one of the most commonly used resistive materials because it has low TCR and highly stable resistance. In this work, we fabricated thin film resistors using Evanohm alloys target(72Ni-20Cr-3Al-4Mn-Si) of s-type with excellent resistors properties by RF-sputtering. Also we reported best deposited conditions of thin film resistors for microwave to observe microstructure and electronic properties of thin film according to deposited conditions(between target and substrate, power supply)

• Journal of the Semiconductor & Display Technology
• /
• v.9 no.1
• /
• pp.29-33
• /
• 2010

Recently, the growth of ZnO thin film on glass substrate has been investigated extensively for transparent thin film transistor. We have studied the phase transition of ZnO thin films from metal to semiconductor by changing RF power in the deposition process by RF magnetron sputtering system. The structural, electric, and optical properties of the ZnO thin films were investigated. The film deposited with 75 watt of RF power showed n-type semiconductor characteristic having suitable resistivity $-3.56\;{\times}\;10^{+1}\;{\Omega}cm$, carrier concentration $-2.8\;{\times}\;10^{17}\;cm^{-3}$, and mobility $-0.613\;cm^2V^{-1}s^{-1}$ while other films by 25, 50, 100 watt of RF power closed to metallic films. From the surface analysis (AFM), the number of crystal grain of ZnO thin film increased as RF power increased. The transmittance of the film was over 88% in the visible region regardless of the change in RF power.

• Journal of the Korean institute of surface engineering
• /
• v.29 no.6
• /
• pp.666-672
• /
• 1996

The optical property of CdTe thin film is important for applications such as the compound semiconductor type solar cells. CdTe films are prepared by RF sputtering at various substrate temperature between $25^{\circ}C$ and $300^{\circ}C$, then, annealed in argon gas environment at $400^{\circ}C$. The annealing process of the thin film caused variation in the film structure and the composition of films. The deformation of CdTe thin film was observed by X-ray diffractometry. After annealing, the grain size increased and the portion of the non-crystalline CdTe reduced. Futhermore, the structure of sputtered CdTe film grown at the substrate temperature more than $250^{\circ}C$ was enhanced in the (111) direction of zincblend structure. There was a discrepancy, in the spectroscopic ellipsometer spectrum, between the single crystal CdTe and the sputtered CdTe thin films, especially in the region over 3.2eV. An oxidation layer was found on the CdTe thin film by spectroscopic ellipsometry analysis.