• Journal of the Korean institute of surface engineering
• /
• v.34 no.5
• /
• pp.481-485
• /
• 2001

We investigated the structural and electrical properties of the Ba ($Zr_{x}$ $T_{il-x}$ )$O_3$ (BZT thin films with a mole fraction of x=0.2 and thickness 150 nm for the application in MLCC (Multilayer Ceramic Capacitor). BZT films were prepared on $Pt/SiO_2$/Si substrate at various substrate temperatures by the RF-magnetron sputtering system. When the substrate temperature was above $500^{\circ}C$, we could obtain multi-crystalline BZT films oriented at (110), (111), and (200) directions. The crystallization of the film and high dielectric constant were observed with the increase of substrate temperature. Capacitance of the film deposited at high temperature is more sensitive to the applied voltage than that of the film deposited at low temperature. This paper reports surface morphology, dielectric constant, dissipation factor, and C-V characteristics for BZT films deposited at three different temperatures. The BZT film deposited at 40$0^{\circ}C$ shows stable electrical properties but a little small dielectric constant for MLCC application.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.07a
• /
• pp.263-266
• /
• 2001

In this paper, we investigated dielectric properies for BST thin films that was deposited on MgO/Si substrates using RF magnetron sputtering. In here, MgO film was used to perform that a diffusion b arrier between the BST film and Si substrate and a buffer layer to assist the BST film growth. A d eposition condition for MgO films was RF Power of 50W, substrate temperature of room temperature and the working gas ratio of Ar:O$_2$ were varied from 90:10 to 60:47. Finally we manufactured the cap acitor of Al/BST/MgO/Si/Al structure to know electrical properties of this capacitor through I-V, C-V measurement. In the results, C-V aha racteristic curves was shown a ferroelectric property so we measured P-E. A remanent poliazation and coerceive electric field was present 2$\mu$C/cm$^2$ and -27kV/cm respectively at Ar:O$_2$=90:10. And a va clue of dielectric constant was 86 at Ar:02=90:10.

• The Korean Journal of Ceramics
• /
• v.2 no.2
• /
• pp.95-101
• /
• 1996

Variations of the leakage current behaviors and interface potential barrier $({\Phi}_B)$ of rf-sputter deposited (Ba, Sr)$TiO_3$ (BST) thin films with thicknesses ranging from 20 nm to 150nm are investigated as a function of the thickness and bias voltages. The top and bottom electrodes are dc-sputter-deposited Pt films. ${\Phi}_B$ critically depends on the BST film deposition temperature, postannealing atmosphere and time after the annealing. The postannealing under $N_2$ atmosphere results in a high interface potential barrier height and low leakage current. Maintaining the BST capacitor in air for a long time reduces the ${\Phi}_B$ from about 2.4 eV to 1.6 eV due to the oxidation. ${\Phi}_B$ is not so dependent on the film thickness in this experimental range. The leakage conduction mechanism is very dependent on the BST film thickness; the 20 nm thick film shows tunneling current, 30 and 40 nm thick films show Shottky emission current.

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.1250_1251
• /
• 2009

The SBN thin films are deposited on Pt-coated electrode(Pt/Ti/$SiO_2$/Si) using RF sputtering method at various deposition conditions. The capacitance of SBN thin films were increased with the increase of Ar/$O_2$ ratio and RF power, respectively. Also, The capacitance of SBN thin films were increased with the increase of deposition temperature.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.07a
• /
• pp.70-73
• /
• 2001

MFIS(Metal-ferroelectric-insulator- semiconductor) structures using silicon oxynitride(SiON) buffer layers were fabricatied and demonstrated nonvolatile memory operations. Oxynitride(SiON) films have been formed on p-Si(100) by RTP(rapid thermal process) in O$_2$+N$_2$ ambient at 1100$^{\circ}C$. The gate leakage current density of Al/SiON/Si(100) capacitor was about the order of 10$\^$-8/ A/cm$^2$ at the range of ${\pm}$ 2.5 MV/cm. The C-V characteristics of Al/LiNbO$_3$/SiON/Si(100) capacitor showed a hysteresis loop due to the ferroelectric nature of the LiNbO$_3$ thin films. Typical dielectric constant value of LiNbO$_3$ film of MFIS device was about 24. The memory window width was about 1.2V at the electric field of ${\pm}$300 kV/cm ranges.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.20 no.7
• /
• pp.575-580
• /
• 2007

A 16 Mb 1T1C FeRAM device was integrated with BLT capacitors. But a lot of cells were failed randomly during the measuring the bit-line signal distribution of each cell. The reason was revealed that the grain size and orientation of the BLT thin film were severely non-uniform. And the grain size and orientation were severely affected by the process conditions of post heat treatment, especially nucleation step. The optimized annealing temperature at the nucleation step was $560^{\circ}C$. The microstructure of the BLT thin film was also varied by the annealing time at the step. The longer process time showed the finer grain size. Therefore, the uniformity of the grain size and orientation could be improved by changing the process conditions of the nucleation step. The FeRAM device without random bit-fail cell was successfully fabricated with the optimized BLT capacitor and the sensing margin in bit-line signal distribution of it was about 340 mV.

• Korean Journal of Materials Research
• /
• v.10 no.9
• /
• pp.607-611
• /
• 2000

Zr modified $(Ba_{1-x},Sr_x)TiO_3$ thin films as capacitor for high density DRAM were deposited by r.f. magnetron sputtering. The films deposited at various chamber pressure exhibited a polycrystalline structure. The Zr/Ti ratio of the films increased significantly with decreasing the chamber pressure and this variation affected the microstructure and surface roughness of films When chamber pressure increased dielectric constant of the films effected due to decrease of Zr. The thin films prepared in this study show dielectric constant of 380 to 525 at 100KHz. The variation of capacitance and polarization measured as a function of bias voltage suggested that all films were paraelectric phases. Leakage current exhibited smaller value as chamber pressure decrease and the leakage current density of the films deposited above 10mTorr was $10^{-7}~10^{-8}A/cm^2$ order at 200kV/cm. $(Ba_{1-x},Sr_x)(Ti_{1-y},Zr_y)O_3$ thin films in this study appeared to be potential thin film capacitor for high density DRAM.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.14 no.7
• /
• pp.567-571
• /
• 2001

We investigated the structural and electrical properties of Ba(Zr$_{x}$Ti$_{1-x}$ )O$_3$(BZT) thin films with a mole fraction of x=0.2 and a thickness of 150 nm. BZT films were prepared on Pt/SiO$_2$/Si substrate with the various substrate temperature by a RF magnetron sputtering system. When the substrate temperature was above 50$0^{\circ}C$, we obtained multi-crystalline BZT films oriented to (110), (111), and (200) directions. As the substrate temperature increases, the films are crystallized and their dielectric constants become high. C-V characteristic curve of the film deposited at high temperature is more sensitive than that of the film deposited at low temperature. The parameters of the BZT film are as follows; the dielectric constants(dissipation factors) at 1 MHz are 95(0.021), 140(0.024), and 240(0.033) deposited at 400, 500, $600^{\circ}C$, respectively; the leakage currents at 666.7 kV/cm are 5.73, 23.5, and 72.8x10$^{-8}$ A/$\textrm{cm}^2$ fo the films deposited at 400, 500, and 600 $^{\circ}C$, respectively; the leakage currents at 666.7kV/cm are 5.73, 23.5, and 72.8x10$^{-8}$ A/$\textrm{cm}^2$ for the films deposited at 400, 500, $600^{\circ}C$, respectively. The BZT film deposited at 40$0^{\circ}C$ shows stable electrical properties, but dielectric constant for application is a little small.ll.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.179-179
• /
• 2009

This is for the electrical characterization by IDC pattern using BST$(Ba_{0.5}Sr_{0.5}TiO_3)$ thin film. BST materials had been chosen for high frequency applications due to it's high permitivity and tunability. The BST thin films have been deposited on $Al_2O_3$ Substrates by Nd-YAG pulsed laser deposition with a 355nm wavelength at $700\;^{\circ}C$. The post deposition annealing at $750^{\circ}C$ in flowing $O_2$ atmosphere for 1 hours. The capacitance of IDC patterns have been measured from 1 to 10 GHz as a function of electric field ($\pm40$ KV/cm) at room temperature using inter-digital Au electrodes deposited on top of BST. The IDC patterns have three type of fingers number. For the 10 pairs finger was the best capacitance onto $Al_2O_3$ substrate. The capacitance was 0.9pF. Also Dielectric constant was been 351 at 100 mTorr and annealing temperature $750^{\circ}C$ for 1 hour. The loss tangent was been 0.00531.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.200-200
• /
• 2008

This paper reports on electrical characterization by IDC pattern using BST$(Ba_{0.5}Sr_{0.5}TiO_3)$ thin film. BST thin films have been deposited on $Al_2O_3$ Substrates by Nd-YAG pulsed laser deposition with a 355nm wavelength at $700^{\circ}C$. The post deposition annealing at $750^{\circ}C$ in flowing $O_2$ atmosphere for I hours. The capacitance of IDC patterns have been measured from 1 to 10 GHz as a function fo electric field (${\pm}40$ KV/cm) at room temperature using interdiigitated Au electrodes deposited on top of BST. The IDC patterns have three type of fingers number. For the finger paris was increased onto $Al_2O_3$, the capacitance increased. The capacitance of 5 pairs finger was 0.3pF and 10 pairs finger was 0.9pF.