• Transactions of Materials Processing
• /
• v.8 no.6
• /
• pp.554-562
• /
• 1999

In this paper, the stress and strain behavior in near homogeneous isotropic matrix of metal like steel was studied during roll forming of thin steel sheet for cylindrical pipe. Analytical result reveals a body which is on the area of square thickness along and perpendicular to the width of thin steel sheet is in the state of plane strain during roll forming. As a result, construction of analytical method for calculating deformation load and stably deformed length along the width of strained steel sheet was established. Also, loads applied during roll forming were analyzed using two typical thin steel sheets. 12.3mm thick steel sheet with 42.5kg/㎟ yield strength of pipe and 5.3mm thick steel sheet with 32.5kg/㎟ yield strength of pipe. Through this analysis, applicability of the analytical method for deformation load during roll forming of cylindrical thin steel pipe was evaluated with a study of necessary production technology for roll forming and design technology for roll forming machine.

• Korean Journal of Metals and Materials
• /
• v.49 no.2
• /
• pp.192-196
• /
• 2011

The multi-layered thin film with an ITO/Ag/ITO structure was produced on PET by using magnetron reactive sputtering method. First, 30 nm of ITO thin film was coated on PET by using normal temperature process. Then 20-52 nm of the Ag thin film was coated. Lastly, 30 nm of ITO thin film was coated on Ag layer. The sample of the 20 nm Ag thin film showed more than 70% transmission and a $2.7{\Omega}/{\Box}$ sheet resistance. When compared to the existing single-layered transparent conducting thin film, multi-layered film was found to be superior with about $5{\Omega}/{\Box}$ less sheet resistance. However, since the Ag layer became thinner, the band gap energy needs to be increased to more than 3.5 eV.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2015.11a
• /
• pp.344-345
• /
• 2015

Various concentration of copper was dopped in Fe-35%Ni thin sheet by electroforming and their electromagnetic, surface properties were determined. Microstructure observation by scanning electron microscopy revealed that the thin sheet had columnar grains with about 150 nm long. Phase analysis by X-ray diffractometry revealed that the alloy thin sheets were fine crystalline. The average surface roughnesses measured by atomic force microscopy (AFM) were about 14.38 nm. Nano hardnesses determined by tribo-nano indenter were 4.13 GPa. The surface resistances were 2.28 ohm/sq. The maximum magnetization, residual magnetization and coercive force depended on the copper concentration.

• Transactions of Materials Processing
• /
• v.22 no.3
• /
• pp.133-142
• /
• 2013

Recently, electric vehicles and hybrid cars are being promoted as alternatives to reduce automobile emissions. Generally, thin sheet materials such as aluminum alloy AA300X and cold-rolled steel sheet such as JIS-G-3141 are used for the container for the lithium-ion secondary batteries. In this study, a multi-stage deep drawing process is used to produce a rectangular cup from thin stainless steel sheet material, SUS409L, with an initial blank thickness of 0.4mm for the battery container application. Numerical simulations of the first through the fifth stages for the multi-stage deep drawing with thin SUS409L sheet were conducted using LS-Dyna3D Implicit/Explicit. Special consideration was given to the deformation characteristics due to the normal anisotropy of the sheet material. The numerical simulations were conducted with both isotropic properties and the anisotropic properties of the initial blank material. An unexpected forming failure, barreling in the bottom region of the deep drawn rectangular cup, was observed. This failure mode can be avoided by additional ironing thickness control during the process.

• Transactions of Materials Processing
• /
• v.28 no.6
• /
• pp.328-335
• /
• 2019

Demand for ultra-thin materials is increasing due to their light-weight and versatile properties. In this work, the formability of the ultra-thin stainless steel sheets of various thicknesses in the incremental sheet forming (ISF) process is investigated. The effects of the thickness on formability were evaluated with forming experiments of the truncated cone shape with 10° intervals. As the thickness of the material decreased, the maximum forming angle decreased and wrinkles also occurred quickly. The maximum forming angles in the truncated cone shape without the wrinkles for the thickness of 0.05 mm, 0.08 mm, and 0.1mm were 30°, 40°, and 50°, respectively. Wrinkles occurred in a twisted shape along the moving direction of the tool. As the material thickness increased, the size of the wrinkles increased.

• Journal of the Semiconductor & Display Technology
• /
• v.14 no.3
• /
• pp.33-36
• /
• 2015

It has increased several decades in the field of Indium Tin Oxide (ITO) transparent thin film, However, a major problem with this ITO thin film application is high cost compared with other transparent thin film materials[1]. So far, in order to overcome this disadvantage, we show that a transparent ITO/Ag/i-ZnO multilayer thin film electrode would be more cost-effective and it has not only highly transparent but also conductive properties. The aim of this research has therefore been to try and establish how ITO/Ag/i-ZnO multilayer thin film would be more effective than ITO thin film. Herein, we report the properties of ITO/Ag/i-ZnO multilayer thin film by using optical spectroscopic method and measuring sheet resistance. At a certain total thickness of thin film, sheet resistance of ITO/Ag/i-ZnO multilayer was drastically decreased than ITO layer approximately $40{\Omega}/{\Box}$ at same visible light transmittance. (minimal point $5.2{\Omega}/{\Box}$). Tendency, which shows lowly sheet resistive in a certain transmittance, has been observed, hence, it should be suitable for transparent electrode device.

• Journal of the Korean institute of surface engineering
• /
• v.38 no.2
• /
• pp.55-59
• /
• 2005

ITO/Ni/ITO thin films were deposited on the PET by RF magnetron sputtering. Dependance of the process parameters such as deposition pressure, positions of Ni layer, on the transmittance, reflectance and sheet resistance of ITO/Ni/ITO film were investigated. When the Ni layer is placed at the center of ITO and deposition pressure is low, ITO/Ni/ITO films showed better optical and electrical properties. At these conditions, the transmittance, reflectance and sheet resistance of the ITO film were $90\%,\;0.38\%$ and $185\Omega/\Box$ respectively.

• Transactions of Materials Processing
• /
• v.19 no.3
• /
• pp.179-184
• /
• 2010

The present study is focused on the deep drawability and product qualities of ultra thin beryllium copper sheet metal. The goal of this research is to investigate the limit drawing ratio in deep drawing of ultra thin beryllium copper metal. For the experiment, beryllium copper(C1720, $50{\mu}m$ in thickness) is used. Tensile test are also carried out to find out the material properties. Deep drawing experiments are carried out in Universal Testing Machine(UTM) to obtain limit drawing ratio. Deep drawing tests are carried out for various specimen sizes. Teflon film is used as a lubricant and constant blank holding force is imposed. Sheet thickness and surface hardness are measured along radial direction after deep drawing. Thickness is measured using optical microscope. For beryllium copper(C1720), the maximum LDR of 2.4 is obtained when the die shoulder radius is 20 or 30 times of sheet thickness.

• Transactions of Materials Processing
• /
• v.17 no.8
• /
• pp.643-648
• /
• 2008

Ultra-thin sheet metal forming techniques are required in precision forming of miniaturized and integrated products. In order to manufacture a good quality and low cost ultra-thin sheet metal products, a highly precise high-speed press is needed. The precision of a press is related with its vibration characteristics during pressing operation. This study evaluated the vibration characteristics of a proposed press design using computer simulation. The analysis compares the static deformation characteristics of the slide and the slide motion for the metal forming of an ultra-thin sheet of thickness less than 0.1mm. Further, in order to minimize the vibrations during high speed pressing operation, revolution balances of the eccentric shaft and the balance weight device is also considered. Finally, modal analysis is used to characterize the natural frequency of vibration of the press.

• Transactions of Materials Processing
• /
• v.30 no.4
• /
• pp.179-185
• /
• 2021

Lithium ion batteries are generally manufactured by laser and etching using aluminum thin sheet. These processes are relatively expensive and have low productivity. In this study, blanking process of aluminum thin sheet for lithium ion battery was employed to replace laser cutting and etching process, all to reduce the production cost and improve productivity. Mechanical properties for aluminum and coating were determined by experimental results and rule of mixture for FE analysis of blanking process. Normalized Cockcroft-Latham criteria was also applied to describe shear behavior and critical damage values were determined by comparison of analytical and experimental result. We performed FE analysis to investigate the effects of clearance and punch-die radius on sheared surface of aluminum thin sheet and to determine optimal process condition. We manufactured the die set using the determined optimal process and conducted an experiment to confirm the feasibility of blanking process. The sheared surface of manufactured product was observed by optical microscope. As a results, the proposed process conditions successfully achieved the dimensional requirement in production of lithium ion battery parts.