• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2004년도 춘계학술발표대회 및 제6회 신소재 심포지엄
• /
• pp.33-33
• /
• 2004

• 한국초전도학회:학술대회논문집
• /
• 한국초전도학회 2004년도 High Temperature Superconductivity Vol.XIV
• /
• pp.57-57
• /
• 2004

• 한국전기전자재료학회논문지
• /
• 제20권6호
• /
• pp.520-526
• /
• 2007

In order to acquire fundamental informations to fabricate high precision thin film resistors, NiCr/NiCrSi alloy films were prepared using Ni and Cr targets. Effect of composition on the electrical properties of the NiCr/NiCrSi alloy film were then investigated. Considering the effect of Si doping on the electrical and material characteristics, the lower TCR (temperature coefficient of resistance) values could be achieved for samples with Ni/Cr ratio of $0.8{\sim}1.5$ (in a range of relative higher specific resistivity and Cr composition of $40\;wt%{\sim}55\;wt%$) and with Si doping. Consequently, the sample prepared using a DC power showed a good TCR of $-25\;ppm/^{\circ}C$, which implies that increase of specific resistivity and decrease of TCR would be achieved more efficiently not for Ni-Cr binary material but for Si doped Ni-Cr ternary material, and not using RF power but using DC power in the sputtering process.

• 마이크로전자및패키징학회지
• /
• 제11권1호
• /
• pp.37-42
• /
• 2004

최근에 3 ㎓이상의 고주파용 전자부품과 소자의 제조에 낮은 저항온도계수(TCR)값과 높은 정밀도를 갖는 박막저항이 사용되고 있다. Ni-Cr 박막저항은 낮은 TCR 값과 저항에 대한 높은 안정성 때문에 저항 물질로 사용되는 가장 일반적인 물질이다. 본 연구에서는 $Ni_{72}Cr_Al_3Mn_4Si$(wt%)이 첨가된 우수한 저항특성을 갖는 S-type의 Evanohm 합금 타겟과 스퍼터링 장비를 이용하여 박막 저항을 제조하였다. 또한 열처리 조건을 $200^{\circ}C$, 300$300^{\circ}C$, $400^{\circ}C$, $500^{\circ}C$로 변화시키면서 고주파 박막 저항의 미세구조와 전기적 특성을 관찰하여 최상의 열처리 조건을 알아보았다.

• 한국마이크로전자및패키징학회:학술대회논문집
• /
• 한국마이크로전자및패키징학회 2003년도 기술심포지움 논문집
• /
• pp.145-150
• /
• 2003

최근에 3 GHz이상의 고주파용 전자부품과 소자의 제조에 낮은 TCR 값과 높은 정밀도를 갖는 박막저항이 사용되고 있다. Ni-Cr 박막저항은 낮은 TCR 값과 저항에 대한 높은 안정성 때문에 저항 물질로 사용되는 가장 일반적인 물질이다. 본 연구에서는 $Ni_{72}Cr_{20}Al_3Mn_4Si(wt\%)$ 첨가된 우수한 저항특성을 갖는 s-type의 Evanohm 합금 타겟과 스퍼터링 장비를 이용하여 박막 저항을 제조하였다. 또한 열처리 조건을 $200^{\circ}C,\;300^{\circ}C,\;400^{\circ}C,\;500^{\circ}C$로 변화시키면서 고주파 박막저항의 미세구조와 전기적 특성을 관찰하여 최상의 열처리 조건을 알아보았다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2001년도 하계학술대회 논문집 C
• /
• pp.1399-1401
• /
• 2001

We studied on structure and resistivity, temperature coefficient of resistance (TCR) of NiCr and NiCr-N thin resistor films prepared by do reactive magnetron sputtering of NiCr target. It is found that while pure NiCr films are polycrystalline, an addition of nitrogen (N2/(Ar+N2) ratios are between 10% and 70%) into the film is changed into amorphous structure and sheet resistance of films is increased. Measurement temperatures of TCR are ratios of $5^{\circ}C$ per 15min from $25^{\circ}C$ to $130^{\circ}C$. TCR for an as-deposited NiCr-N thin film is varied from positive to negative.

• Progress in Superconductivity
• /
• 제6권1호
• /
• pp.46-51
• /
• 2004

We fabricated a resistive type superconducting fault current limiter (SFCL) of 3-phase $6.6 kV_{rms}$ / rating, based on YBCO thin films grown on sapphire substrates with a diameter off inch. Each element of the SFCL was designed to have the rated voltage of $600 V_{rms}$ $/35A_{rms}$. The elements produced a single phase with 8${\times}$6 components connected in series and parallel. In addition, a NiCr shunt resistor of 23 $\Omega$ was connected in parallel to each of them for simultaneous quenches between the elements. Prior to investigating the performance of the 3 phase SFCL, we examined the quench characteristics for 8 elements connected in series. For all elements, simultaneous quenches and equal voltage distribution within 10% deviation from the average were obtained. Based on these results, performance of the SFCL for single line-to-ground faults was investigated. The SFCL successfully limited the fault current of $10 kA_{ rms}$ below 816 $A_{peak}$ within 0.12 msec right after the fault occurred. During the quench process, average temperature of all components did not exceed 250 K, and the SFCL was totally safe during the whole operation.

• 한국진공학회지
• /
• 제1권1호
• /
• pp.212-222
• /
• 1992

To use polycrystalline Si Thin Film Transistor (poly-Si TFT) in high density SRAM instead of High Load Resistor (HLR), TFT is needed to show good electrical characteristics such as large carrier mobility, low leakage current, high driver current and low subthreshold swing. To satisfy these electrical characteristics, the trap state density must be reduced in the channel poly. Technological issues pertinent to the channel poly fabrication process are investigated and discussed. They are solid phase growth (SPG), Si-ion implantation, laser annealing and hydrogenation. The electrical properties of several CVD oxides used as the gate oxide of TFT are compared. The dependence of the electrical characteristics of TFT on source-drain ion-implantation dose, drain offset length and dopant lateral diffusion are also described.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 추계학술대회 논문집 Vol.15
• /
• pp.411-415
• /
• 2002

Precision resistors were prepared by controlling the concentration of Ni and Cr deposited on cylindrical alumina substrates (diameter: 1.7mm, length: 5.5mm). Deposited films were analyzed with FESEM, AES, and AFM. As the amount of Cr in the film increases, the TCR was shifted to negative direction.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 하계학술대회 논문집
• /
• pp.19-19
• /
• 2009

TiNxOy/TiNx multilayer thin films with a high resistance (~ k$Omega$) were deposited on SiO2/Si substrates at room temperature by sputtering. The TiNx thin films show island and smooth surface morphology in samples prepared by dc and rf magnetron sputtering, respectively. TiNxOy/TiNx multilayer has been developed to control temperature coefficient of resistance (TCR) by the incorporation of TiNx layer (positive TCR) inserted into TiNxOy layers(negative TCR). Electrical and structural properties of sputtered TiNxOy/TiNx multilayer films were investigated as a function of annealing temperature. In order to achieve a stable high resistivity, multilayer films were annealed at various temperatures in oxygen ambient. Samples annealed at 700 oC for 1 min exhibit a good TCR value and a stable high resistivity.