• 한국염색가공학회지
• /
• 제4권3호
• /
• pp.131-135
• /
• 1992

Quaternary aminized cellulosic adsorbents (C $A_{QA}$ ) which exhibit adsorption capacities for anionic dyestuffs for the treatment of colored waste water and re-use of the treated water were studied. The isotherms and thermodynamic parameters of C.I. Acid Orange 7, solution considered as a model of negatively charged coloring matters for C $A_{QA}$ , were determined. Batch method and flow method were employed to determine decoloring capacity of cellulosic adsorbents for Orange 7. The cellulosic adsorbents exhibited much better adsorption capacity than activated carbon. Furthermore the exhausted cellulosic adsorbents could be readily regenerated by washing with dilute sodium hydroxide.

• 설비공학논문집
• /
• 제14권4호
• /
• pp.304-314
• /
• 2002

Performance analysis of the automotive air-conditioning system is conducted by using computer simulation, and performance tests are carried out by using the climate wind tunnel in order to verify simulation. Evaporator and condenser were modeled by using empirical correlation which was obtained from calorimeter data, and compressor was modeled by using map based method. The steady state thermodynamic conditions of refrigerant satisfying mass and energy balance were assumed in the simulation program for automotive airconditioning system. The system performance was analyzed by finite difference method until differential air enthalpy between evaporator inlet and outlet becomes converged. Simulation results are in good agreement with experimental results at most operating conditions. Variation of discharge temperature and pressure of compressor, outlet temperature of evaporator, cooling capacity, and COP were investigated in term of air volume flow rate for evaporator, compressor capacity, compressor speed, superheat of thermostatic expansion valve, and diameter of suction line.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1998년도 제27회 춘계학술대회
• /
• pp.218-227
• /
• 1998

Present study is undertaken to optimize the lubrication reliability and frictional loss of the dynamically-loaded journal bearing in hermetic reciprocating compressor with alternative refrigerant R600a application. Thermodynamic and dynamic analysis has been conducted to investigate cylinder pressure variations by substitution alternative refrigerant R600a for R12. The modeling of the dynamics of the compressor mechanism has been performed with lumped mass method. A mathematical model is developed for analyzing the dynamics of the journal bearing system with the mobility method. It takes into account the effects of the refrigerant species, aspect ratio, clearance ratio and surface roughness. A corresponding computer program is described which enables to obtain the minimum film thickness and frictional loss. Design optimization is graphically performed by parametric studies of the aspect ratio and clearance ratio.

• 한국초전도저온공학회:학술대회논문집
• /
• 한국초전도저온공학회 1999년도 제1회 학술대회논문집(KIASC 1st conference 99)
• /
• pp.169-172
• /
• 1999

The exergy method is used for analysis and evaluation of the cryogenic nitrogen production process which is operated by expansion turbene and liquid nitrogen. The exergy loss and thermodynamic effeciency are calculated for the each process. Also the operating efficiency and the exergy distribution are examined for each unit of proces. The optimal conditions to minimize the exergy loss of nitrogen column are found that nitrogen recovery ratio is maximum and operating pressure is 5.0 kg/cm2g. The exergy method can be used to design a plant and to evaluate its process.

• 한국수소및신에너지학회논문집
• /
• 제29권2호
• /
• pp.163-169
• /
• 2018

The present article discusses about the measurement techniques of acoustic impedance that becomes one of the important acoustic characteristics of various boundaries found inside of propulsion systems. Acoustic characteristics including acoustic impedance and reflection coefficient can be often assessed and estimated by use of the two-microphone method. Theoretical expressions of acoustic impedance and reflection coefficient measured in an impedance tube are presented for both cases with mean flow and without flow, and the practical application of the method through calibration is also provided. The acoustic impedance and the reflection coefficient are related with axial locations of microphones, thermodynamic characteristics of gas inside, and the transfer function between the pressure wave measurements at multiple locations.

• 한국세라믹학회지
• /
• 제31권6호
• /
• pp.685-693
• /
• 1994

Sublimation vapour pressures and sublimation enthalpy of anhydrous bismuth trifluoride have been measured by the continuous gravimetric Cnudsen-effusion method from 639-7 to 782.8 K. Additional effusion measurements have also been made from 750.6 to 863.1 K by the torsion-effusion method. Based on a correlation of subHo298.15 and subSo298.15, a recommended P(T) equation has been obtained for BiF3(s); logP= -C/T+5.2375logT-3.205$\times$10-3+4.661$\times$104/T2+1.348 where P is in Pa, T in Kelvin, subHo298.15 in kJ mol-1 and C=( subHo298.15-13.5149)/1.9146$\times$10-2. Condensation coefficients and their temperature dependence have been derived from the effusion measurements.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2002년도 학술대회지
• /
• pp.229-232
• /
• 2002

For the purpose of Thermal Protection Material design problem, a numerical analysis of axisymmetric high temperature supersonic impinging jet flows of exhaust gas from combustor on curved surfaces has been accomplished. A modifed CSCM Upwind Navier-Stokes method which is able to cure the carbuncle Phenomena has been developed to study strong shock wave structure and thermodynamic wall properties such as pressure and heat transfer rate on various curved surfaces. The results show that the maximum heat transfer rate which is the most important parameter affecting thermo-chemical surface ablation on the plate did not occur at the center of jet impingement, but rather on a circle slightly away from the center of impingement and the shear stress distribution alone the wall is similar to the wall heat transfer late distribution.

• 대한화학회지
• /
• 제35권2호
• /
• pp.105-110
• /
• 1991

수용액 중에서 발린과 노발린의 두 가지 해리상수를 온도와 압력을 변화시키면서 전도도법으로 측정했다. 이들 해리상수로부터 열역학적 성질들을 계산하여 해리반응의 특성을 알아보았다. 아미노산의 종류 즉, 아미노기의 위치나 사슬의 길이, 치환기의 종류에 따라 해리도가 어떤 영향을 받는가 하는 것을 Hammett식을 이용하여 검토했고 이것을 CNDO/2법으로 계산한 분자내 원자의 알짜 전하와 비교 검토하였다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2000년도 춘계학술대회논문집
• /
• pp.1429-1436
• /
• 2000

Suction muffler is one of the important component of a compressor for low noise level and high efficiency. The suction muffler which has the complicated flow path gives the higher transmission loss of sound, but lower efficiency of compressor results from the superheating effect and flow loss in suction flow path. It is shown that the computational analysis of fluid dynamics are very popular methods for designing of high performance and low noise suction muffler. To reduce the thermodynamic and flow loss in suction process, the flow path of suction muffler was estimated by FVM(Finite Volume Method) and verified by experiments. And to enlarge the transmission loss of sound, the acoustic properties inside the suction muffler was analyzed by FEM(Finite Element Method) and experiments. The smart muffler which gives a good efficiency and low noise character was developed by using those methods, and the effect was evaluated in compressor by experiment.

• 대한기계학회논문집
• /
• 제17권7호
• /
• pp.1851-1863
• /
• 1993

A procedure for the prediction of the off-design performance of a gas turbine engine is proposed. The system performance at off-design speed is predicted by coupling the thermodynamic models of a compressor and a turbine. The off-design performance of a compressor is obtained using the stage-stackimg method, while the Ainlay-Mathieson method is used for a turbine. The procedure is applied to a single-shaft gas turbine and its predictability is found satisfactory. The results also show that the net work output increases with the increase of the turbine inlet temperature, while the thermal efficiency is marginal. The maximum thermal efficiency at design point is obtained between the highest pressure ratio and design pressure ratio.