• Proceedings of the SAREK Conference
• /
• 2007.06a
• /
• pp.35-35
• /
• 2007

• Proceedings of the SAREK Conference
• /
• 2007.06a
• /
• pp.36-36
• /
• 2007

• Proceedings of the KIPE Conference
• /
• 2020.08a
• /
• pp.40-42
• /
• 2020

본 논문에서는 리튬이온 배터리의 전기적인 특성 실험을 통해 열 해석에 필요한 인자를 추출하고 이를 이용하여 열 해석의 상용 프로그램인 COMSOL과 ANSYS에서 서로 다른 방법으로 열 해석을 진행한다. 두 프로그램의 열 해석을 통해 얻은 데이터와 측정 데이터를 비교분석 한 결과 유사 경향성을 확인하였고, 이를 통해 전기적 열 해석 모델의 신뢰성을 확보한다.

• Proceedings of the KIEE Conference
• /
• 2004.07c
• /
• pp.1982-1984
• /
• 2004

Stator coil of rotating machinery has shown different characteristics according to impregnated with coil or not. And this is major determinant of equipment's life. In this paper, PD characteristics is studied as a classification scheme between two specimens. Processing of the coil impregnation is very important thing because that influences on thermal and electrical characteristics of the coil. And then PD is occurring at the coil and causing insulation degradation. For processing statistical processing, PD data acquired from PD detector using PDASDA(partial discharge acquisition, storage and display system). And also these statistical distribution and parameter are applied to classify PD sources by neural networks. As a result of, Neural Networks have a good discrimination rate for classification PD sources.

• Journal of Environmental Science International
• /
• v.10 no.4
• /
• pp.311-314
• /
• 2001

The asphalt mixture with CRM(Crumb Rubber Modifier) is known to show a better performance in resisting thermal cracking, fatigue cracking and rutting compared with the conventional mixture. The laboratory tests on the physical characteristics of indirect tensile strength, density, flow and Marshall value of the CRM asphalt were conducted. The test results show that CRM asphalt has better physical characteristics than that of conventional asphalts. And the analysis on the noise reduction effect, penetration capacity from the field test on the national road in Haksan of Chungbuk, and recycling of tire waste were conducted. From this study, the results show that 1% CRM asphalt has higher the noise reduction effect and penetration capacity that those of conventional asphalts. And, optimal contents of crumb rubber modifier in the asphalt binder is one percent. In this case, crumb rubber modifier were used 10 kg to make the asphalt binder of one cubic meter. So it was named as Eco-asphalt.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.27 no.6
• /
• pp.68-74
• /
• 2013

Induction-heated system is innovative system which applied IH(Induction Heating) magnetic induction heating generated from induction-heated metallic package and high-frequency power circuit technique for thermal converse technique. In this occurs not burning, so that the working environment and deterioration of products can be improved. This technique is used high frequency inverter. By using high frequency inverter high frequency in the range of kHz can be made with conventional alternative current. In this contribution IGBT module is used for high frequency inverter. In this paper are discussed analysis of characteristics according to the each frequency and produced Flat plate induction heating system using 1.5kW-class half-bridge resonant inverter. In addition, operating characteristics of the system to changes in the distance between the coil and the heater, applications of system are also discussed.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.10 no.1
• /
• pp.50-55
• /
• 1986

Characteristics of the flow and heat transfer in a channel of 37 rods are investigated numerically. The flow is taken to be a fully developed incompressible laminar flow and it has an uniform temperature profile at the inlet and flows down through the channel of constant wall temperature. A boundary-fitted coordinate system is used for the complex geometry. Calculation is initiated by calculating the developed flow profile and then proceeds to temperature development. Through the calculation the details of the flow and temperature distribution characteristics are found, and discussion is made on the mechanism of the transport phenomena in the complex geometry in terms of wall shear stress distribution, non-dimensionalized velocity, friction factor, Nusselt number distribution, Reynolds number, and porosity. Also the effects of the eccentricity in rod configuration are analyzed and its importance is emphasized.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2008.05a
• /
• pp.436-439
• /
• 2008

It has been known that the value of soil resistance drops when a high impulse curennt is injected into a grounding electrode. In this paper, impulse generator is used to investigate the dry soil and wet soil characteristics in cylinderical test cell. The impulse resistances and breakdown characteristics were discussed based on its voltage and current traces. As a result, sand resistances are decreased with increasing the applied currents. It was thought that a decrease in resistance of dry sand with increasing current is due to both thermal and ionization processes. On the other hand, in case there is no water presence in the soil, the reduction in resistance as the currents are of dry sand increased is mainly due to the ionization process.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2000.04a
• /
• pp.691-696
• /
• 2000

Cooling characteristics of cooling jacket for spindle system with built-in motor are studied. Three dimensional model was selected for the analysis of the helical-type cooling jacket. This model includes the estimation on the amount of heat generation from bearing and built-in motor and the thermal characteristic values such as heat flux on the boundary. The temperature distributions are analyzed and the cooling by Nusselt number and total heat transfer coefficient. Numerical results show that stream-wise cross section area and flow rate are important factors for cooling characteristics of cooling jacket.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.13 no.9
• /
• pp.770-775
• /
• 2000

A new photo-polymer material of the copoly (PM4Ch-ChMA), copoly (poly (4-methacryloyloxy)chalcone-cholesteryl methacrylate) for homeotropic alignment was synthesized and the electro-optical (EO) performance for the photo-aligned vertical-aligned (VA)-LC display (LCD) was studied. Good thermal stabilities of synthesized copolymer were obtained by TGA(Thermogravimetric Analysis) measurement. Good voltage-transmittance (V-T) and response time characteristics for the photo-aligned VA-LCD with polarized UV exposure in oblique direction($\theta$$_{i}$=30$^{\circ}$) on a copolymer-1 (2%) surfaces for 1 min were observed. but, light leakage in the off-state was observed. Therefore, we achieved excellent V-T and response time characteristics for the photo-aligned VA-LCD with UV exposure on a copolymer-3 (30%) surfaces for 3 min.n.