• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.24 no.10
• /
• pp.1008-1016
• /
• 2013

SAR measurement which was applied only to the mobile phone has been expanded in the Korean radio regulation law to the portable wireless communication equipments within 20 cm from the human body since Jan. 2012. The two-way radio operating at 150 MHz frequency band was newly included following the revised radio regulation in the target equipment of measurement. SAR measurement system at 150 MHz satisfying this regulation is necessary accordingly for SAR conformity assessment. The international SAR measurement standard(IEC 62209-2) includes the evaluation method on frequencies above 300 MHz, and the commercial SAR measurement system can measure SAR above 300 MHz only. The size of the reference dipole antenna(760 mm, return loss: -27.57 dB) and flat phantom ($1,300 mm(L){\times}900 mm(W){\times}200 mm(H)$), targeted SAR values for numerical analysis(1 g: 1.08 W/kg, 10 g: 0.77 W/kg) for SAR validation evaluation at 150 MHz frequency are proposed in this paper. The suggested dipole antenna and flat phantom are assembled and used to verify the conformity assessment of commercial SAR measurement system. The measured SAR values of 1 g and 10 g were obtained respectively to be 1.13 W/kg, 0.81 W/kg, and they satisfied the effective range(within ${\pm}10$ %) of IEC international standard. The standards based on this study are expected to be used for the domestic SAR measurement standard and IEC(International Electrotechnical Commission) international standard.

• Asia-pacific Journal of Multimedia Services Convergent with Art, Humanities, and Sociology
• /
• v.9 no.6
• /
• pp.711-718
• /
• 2019

Spectrum analyzer and electromagnetic field meter were used to investigate the EM generation behaviour in different types of home electrical appliances. During microwave oven operation, the EM power measured at a point 30cm apart was measured in the range of 8~11mW/㎡, the strength of the low frequency magnetic field was 60~80mG and the electric field strength was measured at 150~160V/m. For smart phone wireless charging pad, it was measured at an electromagnetic power of 0.4mW/㎡, an electric field of 160 V/m and a magnetic field of 1mG at a point 10cm away. For microwave oven and wireless charging pad, if used within 10cm, the size of the electric field has been measured at a large value that exceeds the human body protection standard and may be hazardous to humans. On the other hand, home appliances such as TVs, hairdryers and refrigerators all showed very low levels of electromagnetic waves, electric fields and magnetic fields, with no harmful effects seen. For electromagnetic shielding, the metal Cu fabric and metal foil had a high level of EM shielding, while polymer films had a low EM shielding characteristic.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.32 no.12
• /
• pp.1825-1836
• /
• 2008

Many applications in computer graphics require complex and highly detailed models. However it is often desirable to use approximations in place of excessively detailed models in order to control the processing time. Thus, we aim to develop a notion of optimal matrix to simplify surface which can rapidly obtain the high quality 2D patterns flattening 3D surface as follows. Firstly, two 3D bodies are modeled based on existing Size Korea data. Secondly, each model is divided by shell and block for its pattern draft. Thirdly, each block is flattened by grid and bridge method. Finally, we selected the optimal matrix and demonstrated the efficiency and quality of the proposed method. This proposed approach accommodates surfaces with darts, which are commonly used in the clothing industry to reduce the deformation of surface forming and flattening. The resulting optimal matrix could be an initiation of standardization for pattern flattening. It is expected that this method could facilitate much better approximation in both efficiency and precision.

• The Journal of Korean Society for Radiation Therapy
• /
• v.25 no.1
• /
• pp.9-14
• /
• 2013

Purpose: High-energy radiotherapy with 10 MV or higher develops photoneutron through photonuclear reaction. Photoneutron has higher radiation weighting factor than X-ray, thus low dose can greatly affect the human body. An accurate dosimetric calculation and consultation are needed. This study compared and analyzed the dose change of photoneutron in terms of space according to the size of photon beam energy and treatment methods. Materials and Methods: To measure the dose change of photoneutron by the size of photon beam energy, patients with the same therapy area were recruited and conventional plans with 10 MV and 15 MV were each made. To measure the difference between the two treatment methods, 10 MV conventional plan and 10 MV IMRT plan was made. A detector was placed at the point which was 100 cm away from the photon beam isocenter, which was placed in the center of $^3He$ proportional counter, and the photoneutron dose was measured. $^3He$ proportional counter was placed 50 cm longitudinally superior to and inferior to the couch with the central point as the standard to measure the dose change by position changes. A commercial program was used for dose change analysis. Results: The average integral dose by energy size was $220.27{\mu}Sv$ and $526.61{\mu}Sv$ in 10 MV and 15 MV conventional RT, respectively. The average dose increased 2.39 times in 15 MV conventional RT. The average photoneutron integral dose in conventional RT and IMRT with the same energy was $220.27{\mu}Sv$ and $308.27{\mu}Sv$ each; the dose in IMRT increased 1.40 times. The average photoneutron integral dose by measurement location resulted significantly higher in point 2 than 3 in conventional RT, 7.1% higher in 10 MV, and 3.0% higher in 15 MV. Conclusion: When high energy radiotherapy, it should consider energy selection, treatment method and patient position to reduce unnecessary dose by photoneutron. Also, the dose data of photoneutron needs to be systematized to find methods to apply computerization programs. This is considered to decrease secondary cancer probabilities and side effects due to radiation therapy and to minimize unnecessary dose for the patients.

• Journal of Advanced Navigation Technology
• /
• v.16 no.2
• /
• pp.360-366
• /
• 2012

In the power distribution panel installed in airport or industrial facilities, MCCB has been used for main switch and ELCB for branch switch to perform human body and leakage-inducing fire protection as well as overcurrent and short circuit protection. Especially for the airport panel, increase in accident protection is needed for stable power supply due to rapid modernization with fast-growing users, higer capacity and diversification of equipment, the increase of power capacity and the breaker made slim is a main issue for now because the issue for installation space is standing out by making panel with two-row arrangement connection method, etc. due to a many use of branch ELCBs. In this thesis, we designed arc extinguishing mechanism, considered movement direction change of contact in mechanism design. Also, we designed the breaker to work stably in case of miniaturization of leakage detection circuit and reverse connection. We conducted short circuit test to verify its function and developed the breaker that can be improved protection against accidental current with slim size operating leakage function when reverse connection to help solve the problem in using space that is increasing in the airport distribution panel.

• Korean Chemical Engineering Research
• /
• v.57 no.3
• /
• pp.305-312
• /
• 2019

The discovery of nitric oxide (NO) as a major signaling molecule in a number of pathophysiological processes - vasodilation, immune response, platelet aggregation, wound repair, and cancer biology - has led to the development of various exogeneous NO delivery systems. However, the development of ideal delivery system for human body application is still left as a challenge due to its high reactivity and short half-life in physiological condition. In this article, an overview of several nano-structures as potential NO delivery system will be presented, along with their recent research results and biomedical applications. Nano-size delivery system has immense advantages compared to others due to its high surface-to-volume ratio and capability for surface modification; thus, it has been proven to be effective in delivering nitric oxide with enhanced performance. Through this novel nano-structure delivery system, we are expecting to achieve sustained release of nitric oxide within adequate range of concentration, which ensures desired drug effects at the target site. Among different nano-structures, in particular, nanoparticle, microemulsion and nanofilm will be reviewed and compared to each other in respect of nitric oxide release profile. The proposed nano-structures for exogeneous NO delivery have a biological significance in that it can be further utilized in diverse biomedical fields as a highly promising therapeutic method.

• The Journal of Korean Society for Radiation Therapy
• /
• v.26 no.1
• /
• pp.83-89
• /
• 2014

Purpose : In case of the intensity modulated radiation therapy (IMRT) using Tomotherapy and linear accelerator (Linac), it was to compare and to evaluate the imaging dose of MVCT and CBCT that were performed daily for the correct set up of the patient. Materials and Methods : The human body model Phantom (Anderson rando Phantom, USA) was divided into the three parts as Head, Thorax, pelvis, and after GafChromic EBT3 film cut to the size of $0.5{\times}0.5cm2$.in the center of the recording area were situated on the ant, post, left, and right surface of the phantom and 2cm in depth from the ant, post, left, right, and center surface of the phantom, the surface dose and inner dose were measured repeatedly three times, respectively, using the tomotherapy (Hi Art) and the OBI of NovalisTx. The measured film calculated the output value by RIP version6.0 and then the average value of the dose was calculated by the one-way analysis of variance. Results : Using the human body model phantom, the results of MVCT and CBCT performance were that measurements of MVCT inner dose were showed $15.43cGy{\pm}6.05$ in the head, $16.62cGy{\pm}3.08$ in the thorax, $16.81cGy{\pm}5.24$ in the pelvis, and measurements of CBCT inner dose were showed $13.28{\pm}3.68$ in the head, from $13.66{\pm}4.04$ in the thorax, $15.52{\pm}3.52$ in the pelvis. The measurements of surface dose were showed in case of MVCT performance, $11.64{\pm}4.05$ in the head, $12.16{\pm}4.38$ in the thorax, $12.05{\pm}2.71$ in the pelvis, and in case of CBCT performance, $14.59{\pm}3.51$ in the head, $15.82{\pm}2.89$ in the thorax, $17.48{\pm}2.80$ in the pelvis, respectively. Conclusion : In case of Inner dose, the MVCT using MV energy showed higher than the CBCT using kV energy at 1.16 times in the head, at 1.22 times in the thorax, at 1.08 times in the pelvis, and in case of surface dose, the CBCT was higher than MVCT, at 1.25 times in the head, at 1.30 times in the thorax, at 1.45 times in the pelvis. Imaging dose was a small amount compared to the therapeutic dose but it was thought to affect partially to normal tissue because it was done in daily schedule. However, IMRT treatment was necessarily parallel with the IGRT treatment through the image-guide to minimize errors between planned and actual treatment. Thus, to minimize imaging dose that the patients receive, when planning the treatment, it should be set up a treatment plan considering imaging dose, or it must be performed by minimizing the scan range when shooting MVCT.

• Parasites, Hosts and Diseases
• /
• v.24 no.2
• /
• pp.121-136
• /
• 1986

Recently there have been some reports on human infections of Echinostoma hortense in Korea. It was found that a few species of freshwater fishes were playing the role of the second intermediate host of E. hortense. However, molluscan intermediate host has not been identified yet in Korea. The present study aimed to establish the life cycle of E. hortense in laboratory. Experimental studies such as egg production from the rat, development of the eggs in vitro, exposure of miracidia to freshwater snails, shedding pattern of cercariae from infected snails, morphology of cercariae, cercarial infection to the second intermediate host and infection of metacercariae to the definitive hosts were done. In addition, epidemiological surveys on the infection status in inhabitants and house rats, and on the natural infection of larval echinostomes in the snails and fishes were carried out along the South Hangang-river. The results obtained were as follows: 1. The eggs deposited from adults in physiological saline were cultivated at room temperature($20{\sim}24^{\circ}C$). The miracidia were firstly observed on 8 days after cultivation, and 85.5% of the eggs contained the mature miracidia on 11 days after cultivation. More than 90% formed the miracidia when cultivated at temperature $22{\sim}27^{\circ}C$. Hatching of the miracidia began on 12 days after cultivation and continued for a week. The size of the miracidia was $103.0{{\times}}51.4{\mu}m$ in average. The motility of the miracidia were active up to 8 hours after shedding, but they were all dead within 10 hours after shedding. 2. A freshwater snail, Radix auricularia coreana was cultivated in aquaria. A hatched $F_1$ snails from the egg masses were exposed to 20 miracidia respectively. Escape of cercariae started on 15 days after infecton. Radix auricularia coreana was experimentally identified as the first intermediate host of E. hortense in Korea. 3. Cercarial shedding started on $15{\sim}20$ days after infection by snail, continued for about 10 days (8.8 days in average). Infected snails were dead within 32 days after the miracidial infection. About 1,335 cercariae($328{\sim}1,994$) per snail were shed in its life, and 119 cercariae in average per snail per day were shed. The cercariae were motile for more than 24 hours, and then squirming at the bottom until death. The body and tail sizes of cercariae were $356{\times}186{\mu}m$ and $510{\times}68{\mu}m$ in average, respectively. The rediae parasitized in the snail hosts were found mainly around the pericardial regions, and their size was $1,575{\times}258{\mu}m$ in average. The numbers of developing cercariae in a mature redia were 14 in average ($7{\sim}20$ in range). The numbers of rediae in a snail were 102 in average on 15 days after miracidial infection and 221 in average on 28 days. 4. Three uninfected Misgurnus anguillicaudatus, less than 6.5cm long were used in for the cercarial infection. They were all exposed with 755 cercariae, and examined at 5-day intervals starting from 10 days after infection. All the fishes were infected with metacercariae of E. hortense and a total of 275 was found infected(36.4%). The metacercariae were fed to rats and the adult worms were obtained on 15 days after infection. 5. The infected rats began to deposit the eggs on 11 days after infection. The number of eggs deposited per day per worm (EPD/worm) was $400{\sim}500$ on 3 weeks after infection and was increased to $1,000{\sim}1,500$ on 4 to 17 weeks, then decreased to 800 on 21 weeks after infection. 6. A total of 745 stool specimens collected from 576 male and 169 female residents of 8 different villages along South Hangang basin was examined. Out of 745 specimens, the eggs of Echinostoma sp. were found in 2 cases (0.3%). Of 34 house rats one showed egg-positive (2.9%). 7. Total 971 Radix auricularia coreana collected from 7 sampling stations were examined for shedding of cercariae. Three snails (0.3%) shed the cercariae of E. hortense. A total of 119 out of 542 freshwater fishes (22.0%) had the metacercariae of E. hortense. The fishes parasitized with the metacercariae were 4 out of 14 examined species. The infection rates of 4 species were 34.1% (106 out of 311) in Misgurnus anguillicaudatus, 30.4% (7 out of 23) in Misgurnus mizolepis, 4.3% (2 out of 46) in Moroco oxycephalus and 22.2% (4 out of 18) in Odontobutis obscura interrupta. In summarizing the above results, the first intermediate host of E. hortense was found as Radix auricularia coreana in Korea. Also, it took about 46 days for the shortest completion of a life cycle of E. hortense in summer; that is, 10 days for miracidial development in eggs, 15 days for cercarial development in the snail, about 10 days for metacercarial development in the second intermediate hosts, and 11 days for the maturation as the adults in the definitive hosts. The natural infection rates of E. hortense in the intermediate hosts were relatively high but those in the definitive hosts were low in the middle areas of South Hangang basin.

• Economic and Environmental Geology
• /
• v.50 no.5
• /
• pp.341-352
• /
• 2017

Along with Cs-137 (half-life: 30.17 years), Sr-90 (half-life: 28.8 years) is one of the most important environmental monitoring radioactive elements. Rapid and easy monitoring method for Sr-90 using Laser-Induced Breakdown Spectroscopy (LIBS) has been studied. Strontium belongs to a bivalent alkaline earth metal such as calcium and has similar electron arrangement and size. Due to these similar chemical properties, it can easily enter into the human body through the food chain via water, soil, and crops when leaked into the environment. In addition, it is immersed into the bone at the case of human influx and causes the toxicity for a long time (biological half-life: about 50 years). It is a very reductive and related with the specific reaction that makes wet analysis difficult. In particular, radioactive strontium should be monitored by nuclear power plants but it is very difficult to be analysed from high-cost problems as well as low accuracy of analysis due to complicated analysis procedures, expensive analysis equipment, and a pretreatment process of using massive chemicals. Therefore, we introduce the Laser-Induced Breakdown Spectroscopy (LIBS) analysis method that analyzes the elements in the sample using the inherent spectrum by generating plasma on the sample using pulse energy, and it can be analyzed in a few seconds without preprocessing. A variety of analytical plates for samples were developed to improve the analytical sensitivity by optimizing the laser, wavelength, and time resolution. This can be effectively applied to real-time monitoring of radioactive wastewater discharged from a nuclear power plant, and furthermore, it can be applied as an emergency monitoring means such as possible future accidents at a nuclear power plants.

• The Journal of Korean Society for Radiation Therapy
• /
• v.29 no.2
• /
• pp.33-41
• /
• 2017

Objectives: The aim of this study is to evaluate the reproducibility and usefulness of the images through the fusion of CT(Computed tomography) and MRI(Magnetic resonance imaging) using a self-manufactured phantom. We will also compare and analyze the target dose from acquired images. Materials and Methods: Using a self-manufactured phantom, CT images and MRI images are acquired by 1.5T and 3.0T of different magnetic fields. The reproducibility of the size and volume of the small holes present in the phantom is compared through the image from CT and 1.5T and 3.0T MRI, and dose changes are compared and analyzed on any target. Results: 13 small hole diameters were a maximum 31 mm and a minimum 27.54 mm in the CT scan and the were measured within an average of 29.28 mm 1 % compared to actual size. 1.5 T MRI images showed a maximum 31.65 mm and a minimum 24.3 mm, the average is 28.8 mm, which is within 1 %. 3.0T MRI images showed a maximum 30.2 mm and a minimum 27.92 mm, the average is 29.41 mm, which is within 1.3 %. The dose changes in the target were 95.9-102.1 % in CT images, 93.1-101.4 % in CT-1.5T MRI fusion images, and 96-102 % in CT-3.0T MRI fusion images. Conclusion: CT and MRI are applied with different algorithms for image acquisition. Also, since the organs of the human body have different densities, image distortion may occur during image acquisition. Because these inaccurate images description affects the volume range and dose of the target, accurate volume and location of the target can prevent unnecessary doses from being exposed and errors in treatment planning. Therefore, it should be applied to the treatment plan by taking advantage of the image display algorithm possessed by CT and MRI.