• 한국해양바이오학회지
• /
• 제6권2호
• /
• pp.41-46
• /
• 2014

Mussel byssus is a bundle of threads used to attach mussels to wet substrates. Recently, a thin cuticle layer on the byssus has attracted public attentions due to its remarkable toughness - stiff as epoxy resin and extensible as rubber. Here, we observed ultrastructure of the cuticle layer in a far eastern mussel (Mytilus coruscus) to understand underlying mechanisms for the mechanical properties. The cuticle layer observed by TEM was composed of submicron-sized granular inclusions in a continuous matrix phase. In addition, ultrastructural study in the presence of tertiary amine (Tetraethylammonium, TEA) showed an evidence that the cuticle is stabilized by cation-${\pi}$ interaction.

• 한국진공학회지
• /
• 제6권S1호
• /
• pp.122-126
• /
• 1997

the Cu/polyimide system is known to be the best candidate for a multilevel interconnection system due to the low resistance of Cu and to the low dielectric constant of polyimide respectively. Ion beam mixing of Cu(40nm)/polyimide was carried out at room temperature with 80 keV Ar+ and N2+ form $1.5\times$1015 to 15$\times$1015 ions/cm2. The quantitative adhesion strength was measured by a standard scratch test. X-ray photoelectron spectroscopy and x-ray emission spectrocopy are employed to investigate the chemical bonds and the interlayer compound formation of the films Cu/Al/polyimide showed more adhesion strength than Cu/polyimide after ion beam mixing and N2+ ions are more effective in the adhesion enhancement than Ar+ with the same sample geometry. The XES results shows the formation of interlayer compound of CuAl2O4 which can reflect more adhesive Cu/Al/polyimide which has not been reported previously. The latter results is understood by the fact that N2+ ions produce more pyridinelike moiety, amide group and tertiary amine moiety whcih are known as adhesion promotors.

• 대한치과재료학회지
• /
• 제45권4호
• /
• pp.301-310
• /
• 2018

이 연구의 목적은 현재 쓰임이 증가하고 있는 여러 종류의 범용 상아질 접착제와 삼차 아민을 포함 혹은 포함하지 않는 레진시멘트 간의 호환성을 평가하기 위함이다. 총 80개의 사람 대구치를 선정해 레진 블럭에 매몰하여 상아질을 노출시키고 600-grit SiC paper로 연마한 후 3종류의 범용 상아질 접착제 Scotchbond universal (3M ESPE, pH 2.6), G-premio bond (GC, pH 1.5), All bond universal (Bisco, pH 3.2) 및 대조군으로 3-step etch and rinse system인 Scotchbond multipurpose (3M ESPE)를 제조사의 지시대로 적용한 후 광중합 시행하였다. 그 위에 직경 2 mm, 높이 3 mm의 몰드를 이용해 삼차아민을 포함한 레진 시멘트인 Calibra(Dentsply) 혹은 삼차 아민을 포함하지 않는 레진시멘트인 RelyX Ultimate (3M ESPE)를 적용하고 20초간 광중합하였다. 그 후 $37^{\circ}C$ 증류수에 7일간 보관 후 미세전단강도를 측정하였다. 각 결과값을 ANOVA와 Tukey test로 분석하였다. 실험 결과 Calibra를 사용한 경우 Scotchbond Multipurpose와 All bond Universal adhesive 적용시 G-premio bond 및 Scotchbond universal adhesive를 적용했을 때에 비해 유의하게 높은 미세전단강도를 나타냈다(p<0.05) RelyX Ultimate를 사용한 경우 adhesive간의 유의한 차이가 관찰되지 않았다(p>0.05).

• Macromolecular Research
• /
• 제17권10호
• /
• pp.776-784
• /
• 2009

N,N-dimethyldodecylamine (tertiary amine)-modified MMT (DDA-MMT) was prepared as an organically modified layered silicate (OLS), after which styrene-butadiene rubber (SBR) nanocomposites reinforced with the OLS were manufactured via the latex method. The layer distance of the OLS and the morphology of the nanocomposites were characterized by X-ray diffraction (XRD) and transmission electron microscopy (TEM). By increasing the amount of N,N-dimethyldodecylamine (DDA) up to 2.5 g, the maximum values of torque, tensile strength and wear resistance of the SBR nanocomposites were increased due to the increased dispersion of the silicate layers in the rubber matrix and the increased crosslinking of the SBR nanocomposites by DDA itself. When SBR nanocomposites were manufactured by using the ternary filler system (carbon black/silica/OLS) to improve their dynamic properties as a tire tread compound, the tan $\delta$(at $0^{\circ}C$ and $60^{\circ}C$) property of the compounds was improved by using metal stearates instead of stearic acid. The mechanical properties and wear resistance were increased by direct substitution of calcium stearate for stearic acid because the filler-rubber interaction was increased by the strong ionic effect between the calcium cation and silicates with anionic surface. However, as the amount of calcium stearate was further increased above 0.5 phr, the mechanical properties and wear resistance were degraded due to the lubrication effect of the excessive amount of calcium stearate. Consequently, the SBR/organoclay nanocomposites that used carbon black, silica, and organoclay as their ternary filler system showed excellent dynamic properties, mechanical properties and wear resistance as a tire tread compound for passenger cars when 0.5 phr of calcium stearate was substituted for the conventionally used stearic acid.

• 공업화학
• /
• 제5권1호
• /
• pp.90-98
• /
• 1994

구연산-초산-유산계에서 구연산의 반응추출에 영향을 미치는 여러 인자를 규명하기 위하여 추출제로 2급과 3급아민 및 용매화추출제를, 용매로 n-butylacetate, MIBK, kerosine 및 xylene 등을, modifier로서 tributyl-phosphate(TBP)와 isodecanol이 이용되었다. 그 외에 수용액상의 pH와, 온도의 영향을 연구하였고 평형상수도 얻었다. NaOH, $Na_2CO_3$ 및 $K_2HPO_4$ 알칼리 수용액에 의한 재추출 실험도 하였다. 실험결과 구연산의 추출에서 2급아민인 di-isotridecylamine(DITDA)이 추출도와 선택성에서 가장 좋았고 용매로서는 n-butylacetate가, modifier로서는 TBP가 우수하였다. 이외에도 수용액의 pH와 추출계의 온도가 낮을수록 추출도가 높았다. 재추출도는 stripping상의 염기도와 온도가 낮을수록 높아졌고 알카리 농도가 커질수록 높아졌다.

• 한국자동차공학회논문집
• /
• 제22권2호
• /
• pp.67-75
• /
• 2014

Biodiesel as alternative fuels has been widely studied due to biodiesel merits such as lower sulfur, lower aromatic hydrocarbon and higher oxygen content. But biodiesels could be easily oxidized by several conditions. In this study, various antioxidants such as propyl gallate, TBHA, TBHQ, DTBHQ, butyl-amin, aniline and pyrogallol were added in the biodiesel produced by the used cooking oil, then the material property test and the vehicle emissions test were conducted in accordance with test method. From the results of material property test, all antioxidants were suitable for the quality standard of density and kinematic viscosity, but Propyl gallate and Pyrogallol, as a type of Gallate additives, showed that the result of TAN increased rapidly according to the increase of the amount of additives. In the oxidation stability test, TBHQ, Butyl-amine and Aniline showed the excellent oxidation stability. Also, when considering the material property test, TBHQ was verified to the most excellent additives. In case of the vehicle emissions test, the testing was conducted by using the biodiesel added by TBHQ and was conducted by using two light duty diesel vehicles suitable for the EURO 4 and EURO 5 emission regulation. The result of testing showed that when the TBHQ was added, the amounts of CO, NOx and NMHC+NOx were decreased but the amount of $CO_2$ was increased.

• Restorative Dentistry and Endodontics
• /
• 제26권1호
• /
• pp.23-31
• /
• 2001

The purpose of this study was to search the optimal silane concentrations for filler- silanization of seven experimental composites. Silica filer was a 25micron crushed type. 0.0%, 0.5%, 1.0%, 1.5%, 2.0%, 2.5%, and 3.0% silane($\gamma$-methacrylooxypropyltrimethoxysilane)were added into silica-filler with weight percentage (wt%). Mixtures(silica filler/silane)were reacted at 6$0^{\circ}C$ for 72hours, and crushed into fine particles those were used as fillers for 7 experimental composites. Monomer was a 3 : 1 mixture of Bis-GMA and TEGDMA containing 0.2% tertiary amine and 0.4% camphoroquinone for light curability. A ratio for mixing the monomer and filler was 75% and 25% respectively. Seven experimental composites was classified with the concentration of silane treated, and the specimen number for each test was 10. Specimens with 6mm diameter and 3mm height dimension for measuring the diametral tensile strength were destroyed with 1mm/min cross-head speed on Instron universal testing machine (No. 4467, USA). Shear bond strength was measured on the specimens bonded to bovine enamel etched with 37% phosphoric acid solution for 1 minute Fractured surfaces were observed by SEM (Hitachi S-3200, Japan) among that of the highest values measured from each groups. Following results were obtained: 1. Experimental composites containing silanized filter showed the significantly higher diametral tensile strength and shear bond strength than the composites containing un-silanized fillers(Group1) (p<0.05). 2. In silanized filler composite resins(Group 2~7), Diametral tensile strength of Group 3 showed the significantly higher than that of Group 2 and Group 6(p<0.05). 3. Shear bond strength was higher in Group 3 than that of Group 7 (p＜0.05)in silanized fillers composite resins. 4. Fracture surface was formed in resin matrixes on the specimens from composites containing the fillers treated with 0.5% 1.0%, and 1.5% silane. These results mean that the optimal silane concentrations are exist for each fillet with its size and surface area, and that 1.0% is a optimal value for concentration to coat the 25$\mu\textrm{m}$ filler with silane.

• Restorative Dentistry and Endodontics
• /
• 제26권1호
• /
• pp.41-50
• /
• 2001

The purpose of this study was to examine the influences of camphoroquinone on the properties of five experimental composites. The contents of camphoroquinone were varied as 0.2%, 0.3%, 0.4%, 0.5%, and 0.6%, with silanized filler 75% and tertiary amine 0.2%. Five kinds of experimental composites were prepared, and diametral tensile strength, shear bond strength, depth of cure and yellowish discoloration were tested as a measurement. Specimen numbers of 10 were applied to all test items and experimental groups. Specimens for testing the diametral tensile strengths with internal diameter of 6mm in diameter and 3mm in height were filled with 5 experimental composites which were crushed with 1mm/min cross-head speed on Instron universal testing machine (Model No. 4467). Shear bond strength was measured on specimens attached to bovine teeth enamel etched with 37% phosphoric acid. Depth of cure was measured by the measurement of height of specimens which were removed the un-polymerized portion with acetone. Yellowness measurements were made by chromometer(Minolta Co. Japan) using L$^*$a$^*$b$^*$ values. ANOVA and Multiple range tests were used analyzed data with confidence level at 95%. The mean value of the shear bond strengths ranged from 31.03MPa to 39.49MPa. Following results were obtained ; 1. Diametral tensile strength was highest in experimental group 3, then was not affected by the contents of camphoroquinone ($r^2$=0.0422). 2. Composite resins containing 0.4% camphoroquinone showed the highest shear bond strength, but there was no statistical significance (p=0.3718). 3. Camphoroquinone reduces the depth of cure in the composite resins (p=0.0004, $r^2$=0.9483). 4. Camphoroquinone made the composites yellowish ($r^2$=0.9815). These results mean that increased content of camphoroquinone reduces the depth of cure, and that camphoroquinone make composites yellowish.

• 대한치과보철학회지
• /
• 제41권5호
• /
• pp.606-616
• /
• 2003

Purpose : The purpose of this study was to research the properties of some chemically cured methacrylate polymers such as MMA, HEMA, TEG-DMA, bis-GMA, GMA. Material and Method : 5 kinds of methacrylates were selected and added 2% tertiary amine and benzoyl peroxide to make a chemically curable polymer 25 micron crushed silicas which are treated with silane were selected as filler, they were added into methacrylate monomer until the consistency did not changed by the load of 500gram. All of the experimental resins were 5 kinds, and a serial test was done with 3 kinds of items including the filler contents, the tensile strength, and the bond strength. The number of specimen were 10 for each group. Filler contents were obtained by reducing the specimens to ashes at $600^{\circ}C$ for 1 hour. The specimens with the dimension of 6mm in diameter and 3mm thick were immersed in $37{\pm}1^{\circ}C$ distilled water for 24 hours before test, and tensile strength were measured with cross-head speed 1mm/min. Shear bond strength were mea sured on the specimens attached to bovine enamel etched with 37% phosphoric acid for 1 minute. Results : 1. Maximum filler incorporation was the highest as 75.5% on MMA, and the least as 53.4% on bis- GMA(p<0.0001). 2. The tensile stregth were MMA 141.3, GMA 154.3, TEG-DMA 157.4, bis-GMA 161.4 MPa, and HEMA showed the highest value, 226.9MPa(p = 0.0004). 3. The bond strength were GMA 10.1, TEG-DMA 11.7, HEMA 12.2, bis-GMA 13.3 MPa, and MMA showed the highest value, 15.3MPa, however statistical significances were not (p =0.3838), 4. TEG-DMA and HEMA were not different on the aspect of maximum filler contents and shear bond strength(p>0.05). Conclusion : HEMA can be used as an another diluent substituting TEG-DMA with the increased strength and with the constant bond strength and the constant filler contents.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 1999년도 제17회 학술발표회 논문개요집
• /
• pp.112-112
• /
• 1999

고분자 표면에 MeV급 이온을 주입하게 되면 화학적, 광학적, 물리적, 전기적 특성 등 기존의 재래식 공정으로는 불가능한 다양한 특성변화가 일어나게 된다. 본 실험에서는 이온 조사에 따른 micro-hardness의 변화에 중점을 두어 관찰하였다. 수 MeV로 가속시킨 Cl과 C 이온을 Kapton, Teflon, PMMA에 조사량을 바꾸어가며 조사하였다. 이때 조사 전후 고분자 시료의 표면 경도는 depth-sensing nanoindentation technique (Nano Indenter II, USA)을 이용하여 측정하였다. 측정깊이는 극표면 효과와 기측효과의 영향을 무시할 수 없는 100nm로 결정하였다. 또한 이와 같은 경도변화를 규명하기 위하여 각각의 시료에 대해 FTIR, Raman, UV-VIS, RBS, XPS 스펙트럼을 측정하였으며, 조사중에 발생되는 가스상 분자들을 RGA를 이용하여 측정하였다. 1 MeV Cl 이온을 Kato에 4x1015ions/cm2 조사하면 경도가 0.35 GPa에서 7.1GPa로 약 20배 정도 증가하게 되며, 이 경도는 stainless steel 경도 2~3 GPa, martensite steel 8~12와 비교하여 보면 상당히 높은 수준임을 알 수 있다. Teflon과 PMMA 시료의 경우 1MeV Cl 이온 4X1015ions/cm2를 조사시키면 각각 경도가 0.31GPa에서 4.1a, 0.30 GPa에서 3.9GPa로 변화하였으며 Kapton에 비하여 상대적으로 경도의 변화가 적음을 알 수 있었다. 이온 주입된 Kapton의 경우 FT-IR측정에 의하여 이온 조사량이 증가함에 따라 C=O 진동, 이미드그룹의 CONH, tertiary amine의 C-N 흡수 피크가 감소되며, 1X1014ions/cm2 이상의 양이 조사되어야 개질변화가 일어남을 알 수 있었다. XPS 측정 결과 Kapton에 조사되는 이온양이 증가할수록 C=O, C-O 및 C-N의 탄소는 감소하고 페닐고리 탄소가 증가함을 알 수 있었다. 또한 이온 조사 중 측정한 RGA에서도 CO 가스가 대량 방출되는 현상을 관찰하였으며 FTIR 및 XPS에서의 C=O 결합의 감소와도 일치하였다. RBS에 의한 CNO 원소의 변화에서도 다른 원소보다 O의 감소가 현저하게 나타남을 확인하였다. UV-VIS 측정을 통해 조사 이온량에 따라 에너지 준위가 변동하여 흡수스펙트럼이 장파장으로 확대됨을 알 수 있었으며, 이는 공액 2중 결합의 형성에 의한 $\pi$-전자 및 기타 결함에 기인한다. PMMA 및 Teflon의 경우 FTIR 측정에 의하여 이온 조사됨에 따라 function group 들의 peak가 세기가 감소되면서 완만해지는 경향을 보이며 원래의 구조를 상실하게 된다. PMMA와 Teflon은 이온 조사가 되면 가교형서보다는 사슬절단이 주로 일어나므로 가교형성이 잘 일어나는 Kapton보다는 상대적으로 경도의 증가가 적음을 알 수 있었다.